IP-COM G1110PF-8-102W 9GE+1SFP Ethernet Unmanaged Switch with 8 Port PoE Installation Guide

June 5, 2024
IP-COM

Quich Installation Duide
9GE+1SCP Ethomot Unmanaged Switch with 8-Port PoE G1110PE–102W

G1110PF-8-102W 9GE+1SFP Ethernet Unmanaged Switch with 8 Port PoE

Package contents

– Switch x 1
– Power adapter x 1
– Quick installation guide x 1
This guide instructs how to install and connect the device. For more details, please visit www.ip-com.com.cn. 

Install the device

Preparations You shall prepare the following tools and materials for device installation. – Desktop mounting: ESD bracelet (or ESD gloves) – Wall mounting: ESD bracelet (or ESD gloves), ladder, screwdriver, marker, hammer drill, rubber hammer, leveling instrument, screws (self-prepared: PA3*14 mm, head diameter: 5.2 mm, head height:1.8 mm) and expansion bolts (self-prepared: height: 6.6 mm, inner diameter: 2.4 mm, length: 26.4 mm).
Installation Desktop mounting Horizontally places the switch right-side- up on a big enough, clean, stable, and flat desktop.IP COM G1110PF 8 102W
9GE 1SFP Ethernet Unmanaged Switch with 8 Port PoE- FIG

Wall mounting
Note: – This switch can only be installed on non-flammable walls, such as a concrete walls. – Do NOT install the switch with its air vents facing downward; otherwise, there will be potential safety hazards. – The equipment is suitable for mounting at heights > 2 m.

Step 1 Use a hammer drill to drill 2 holes (diameter: 6 mm) on the wall and the distance between the 2 holes is 113.50 mm. Keep the two holes on a horizontal line.
Step 2
Knock the expansion bolts (self-prepared: height: 6.6 mm, inner diameter: 2.4 mm, length: 26.4 mm) into the holes using a rubber hammer. Use a screwdriver to fix the screws (self-prepared: PA3″14 mm, head diameter: 5.2 mm, head height: 1.8 mm) into the expansion bolts. The distance between the inside surface of the screw header and the edge of the expansion bolt should not be less than 2.5 mm, to make sure that the switch can be hung on the screws firmly.
Step 3 Align the two wall-mounting slots on the bottom of the switch with the two screws on the wall, and then slide the switch to fit in the screws until it is firmly hung on the screws.IP COM G1110PF 8 102W 9GE 1SFP
Ethernet Unmanaged Switch with 8 Port PoE- FIG 1

Connect the device

The typical network topology of the switch is as shown below.

IP COM G1110PF 8 102W 9GE 1SFP Ethernet Unmanaged Switch with 8 Port PoE-
FIG2

Tips – The switch supports auto MDI/MDIX. You can use either a straight- through cable or a crossover cable to connect the switch to Ethernet devices. – The switch supports power supply priorities for the PoE ports. When the total power consumption of the PoE-powered devices exceeds the maximum output of the switch, the switch starts cutting the power supply from the port with the lowest power supply priority (the port with the largest port number) until the total power consumption of the PoE-powered devices is less than the maximum output of the switch.
After connection, you can check whether the switch is connected properly or change the working mode according to the following table. LED indicators
LED indicator
Working mode toggle

LED indicator Description
Power Solid on: Powered on

Off: Powered off or powered improperly
SFP1,
Link/Act (at the upper-left corner of each port)| Solid on: Connected but not active
Blinking: Active in data transmission
Off: Not connected or connected improperly
PoE MAX| Blinking red: Reach max. PoE budget Off Not reaches max. PoE budget

Working mode toggle

Working mode Description
Standard Default mode. In this mode, all ports can communicate with each

other.
VLAN| In this mode, ports 1- 8 are isolated from each other, but all of them can communicate with ports 9 and SFP1. This mode helps isolate DHCP broadcast and reduce broadcast storms.
Extend| In this mode, ports 1- 8 decrease to 10 Mbps in negotiation rate, but transmit up to 250 m in distance.
For better network extension, please use CAT5e or better Ethernet cables, and set the speed and duplex mode of the port of the peer device to “Auto- negotiation”. If the peer device is an IP camera, set its bit rate below 8 Mbps for timeliness of video transmission.
Model| 01110PF-8-102W
---|---
Port| 10/100/1000 Mbps RJ45 port| 9
1000 Mbps SFP port| 1 independent SFP port
Working mode| Standard, VLAN, Extend
Performance| Switching mode| Store-and-forward
MAC addresses table learning| Auto aging, auto-learning
MAC address table| 16 K
PoE power supply| PoE standard| IEEE 802.30, IEEE 802.3at
PoE power cable core| 8 cores: voltage of cores 1, 2, 4, 515 +, and cores 3, 6,7,8 is –
PoE port| 1- 8
The maximum output power of a single port| 30 W
The maximum output power of the switch| 92 W
Dimensions (L x W x H)| 177.5 mm x104 mm x 26mm
Power supply| Input| 100- 240V AC, 50/60Hz,1.6A
Output| 51V DC, 2A
Lightning protection| RJ45 port| Common mode: 6 kV
Power supply| Common mode: 6 kV Differential mode: 4 kV
Operating environment| Temperature: 0°C – 45°C
Humidity: (10% – 90%) RH, non-condensing
Storage environment| Temperature: -40°C -70°C
Humidity: (5% – 90%) RH, non-condensing
Data transmission rate| Ethernet:10 Mbps (half-duplex)/20 Mbps (full-duplex)
Fast Ethernet: 100 Mbps (half duplex)/200 Mbps (full-duplex) Gigabit Ethernet: 2000 Mbps (full duplex)
Transmission media| Ethernet: CATS or better UTP/STP cable
Fast Ethernet: CATS or better UTP/STP cable Gigabit Ethernet: CATSE or CAT6 UTP/STP cable 1000Base-SX: MMF 1000Base-LX: MMF or SMF
Network standards| IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE 802.3ab, IEEE 802.3z, IEEE 802.3af, IEEE 802.3at

FAQ

  1. The Power LED indicator does not light up. What should I do?
    – Ensure that the power adapter is connected to the switch and the power jack properly.
    – Ensure that the power jack is powered on.
    – Ensure that the input voltage matches the value required by the switch.

  2. PoE ports do not supply power for devices. What should I do?
    – Ensure that the powered devices comply with the IEEE 802.3af/at standards.
    – Ensure that the power consumption/total power consumption does not exceed the maximum output power of each port/switch.
    – Ensure that the powered devices are connected to the switch properly with CAT5e or better Ethernet cables.

CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. The mains plug is used as a disconnect device, the disconnect device shall remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
IP COM G1110PF 8 102W 9GE 1SFP Ethernet Unmanaged Switch with 8 Port PoE-
ICONcaution
Adapter Model: BNO38-A10151
Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.
Input: 100-240V AC, 50/60Hz 1.6A
Output: 51V, 2A : DC Voltage

Safety and statement

Before performing an operation, read the operation instructions and precautions to be taken, and follow them to prevent accidents. The warning and danger items in other documents do not cover all the safety precautions that must be followed. They are only supplementary information. The installation and maintenance personnel need to understand the basic safety precautions to be taken.

  1. Do not use this apparatus near water.
  2. Clean only with dry cloth.
  3. . Do not block any ventilation openings, such as newspapers, tablecloth, curtains, etc.
  4. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus that produce heat.
  5. Do not damage the ground conductor or operate the device in the absence of a well-installed ground conductor. Conduct the appropriate electrical inspection.
  6. Protect the power cord from being walk on or pinched particularly at the plugs, convenience receptacles and at the point where they exit from the apparatus.
  7. Only use attachments/accessories specified by the manufacturer.
  8. Unplug this apparatus during lighting storms or when unused for long periods of time.
  9. Mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
  10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
  11. Wanting: To reduce the risk of ire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing.
  12. Warning: To reduce the risk of electric shock, do not remove the cover as there no user-service-able parts inside. Refer servicing to qualified personnel.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiatec radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

RECYCLING
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment.

Technical Support Address: Room 101, Unit A, First Floor, Tower E3, No.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052
Tel: (86755) 2765 3089
Email: info@ip-com.com.cn
Website: www.ip-com.com.cn
Copyright ©2022 IP-COM Networks Co., Ltd. All rights reserved. This documentation (including pictures, images, and product specifications, etc.) is for reference only. To improve internal design, operational function, and/or reliability, IP-COM reserves the right to make changes to the products described in this document without the obligation to notify any person or organization of such revisions or changes.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

IP-COM User Manuals

Related Manuals