LANILIA Wereniso Isola 39 Island Range Hood Instruction Manual

Island range hood
Operating and installation instructions

Wereniso Isola 39 Island Range Hood

Dear Customers,
Thank you for choosing our brand. We hope that you will be satisfied with our product. Every product that leaves our production plant is carefully inspected for quality and safety. Beforinstallation and use of the hood, you are kindly requested to read this manual carefully and follow the safety instructions. We also recommend that you keep the manual in an easily accessible place so that you can consult it at any time.
LANILIA team

In order to ensure the maximum safety of the device, the most important information has been marked with the following symbol:

THE CAUTION SYMBOL INDICATES POSSIBLE DANGERS WHEN USING THE HOOD. FOR YOUR OWN SAFETY, CAREFULLY FOLLOW THE INSTRUCTIONS INDICATED BY THIS SYMBOL!

GENERAL INFORMATION ON SAFETY AND INSTALLATION

• Keep the manual in an easily accessible place so that you can consult it at any time.
• This manual contains detailed information on the installation and maintenance of the range hood.
• The product may slightly differ from the range hood presented in this manual, but the recommendations regarding operation, maintenance and installation apply to the same extent.
• Do not introduce any changes to the electrical installation or physical structure of the hood.
• Do not connect the device to the power supply before completing the installation process.
• Use protective gloves for all installation and maintenance operations.
• Do not use the hood without a properly installed anti-grease filter.
• Installation not in accordance with these instructions poses a risk of electric shock.
• Do not use sources of open fire underneath the hood.
• Keep a close eye during deep frying – overheated fat can easily ignite.
• The air sucked in by the hood must not be discharged into a flue pipe used for exhaust fumes from appliances burning gas or other fuels (this does not apply to recirculation hoods).
• If you have other non-electric appliances in the house (e.g. liquid fuel cookers, flow-through heaters, water heaters) make sure that there is sufficient air supply in the room.
• Do not pull on the power cord to disconnect the plug from the socket.
• The power cord must not be in contact with any hot surfaces.
• Do not switch on the device if the power cord is damaged.
• A damaged power cord may only be replaced by the manufacturer, repair centre or a qualified specialist.
• The hood should be cleaned both inside and outside. at least once a month or every 35 hours of operation. Each time before cleaning the hood, disconnect the power supply (unplug the power cord or pull out the fuses).
• Children at least 8 years old, persons with physical or mental disabilities and persons with lack of knowledge or experience in using the device may use it only under supervision or after being properly instructed in terms of safe operation.
• Children should not be allowed to play with the device.
• Children are not allowed to clean the device without supervision.
  CAUTION!
  EASILY ACCESSIBLE PARTS MAY BECOME HOT WHEN THE COOKER IS USED. USING SCREWS OR FASTENERS OTHER THAN APPROVED IN THE MANUAL MAY  RESULT INELECTRIC SHOCK.

ENVIRONMENTAL PROTECTION

The product is made of high quality recyclable materials.
The symbol of a crossed-out wheelie bin on the product (Fig. 1) indicates that the end users should segregate the product from other waste at end-of-life, in accordance with the provisions of Directive 2012/19/EU of the European Parliament and of the Council. If the symbol shown in Fig. 2 is used, it means that the product contains batteries, which the end users should segregate from other waste at end-of-life, in accordance with the provisions of Directive 2006/66/EU of the European Parliament and of the Council.
The mentioned marking means that end-of-life electrical and electronic equipment and batteries (if any) must not be disposed of with other household waste. The user is obliged to return used electrical and electronic equipment and batteries (if any) to special collection points for such items. Operators of collection facilities, including local collection points, shops and municipal units must have in place an appropriate system enabling the users to return such equipment and batteries.
Proper disposal of waste equipment and batteries prevents harmful impact of hazardous components of these items on human health and the environment, resulting from improper storage and handling of such equipment and batteries. Individual households play an important role in ensuring reuse and recovery, including recycling, of waste equipment, helping to preserve clean environment, which is our common good. It is also households that are the largest consumer of small appliances, hence rational management of waste improves the efficiency of secondary raw materials recovery. Improper disposal of this product may result in penalties, imposed in accordance with national legislation.

TECHNICAL SPECIFICATION

The technical specification presented in this manual and on the labels placed on the product is based on measurements and calculations in accordance with the requirements of EU Regulation 65/2014 and 66/2014.

WERENISO ISOLA 39

WERENISO ISOLA 39

Supply Voltage| 220 – 240V
Frequency:| ~50 Hz
Motor power:| 275 W
Number of speed levels:| 3+1
Lighting power:| 2×5 W
Total Power:| 285 W
Security class:| I
Outlet diameter:| Ø15 cm

INSTALLATION AND OPERATION

The range hood is designed for fume and smoke extraction during food preparation.
CAUTION!

• USE THE SHORTEST POSSIBLE EXHAUST DUCT.
• USE AN EXHAUST DUCT WITH A SMOOTH INTERNAL SURFACE (SPIRO DUCTS ARE NOT RECOMMENDED).
• ANY BENDING OF THE DUCT SHOULD BE LIMITED TO MINIMUM (THE ANGLES SHOULD NOT EXCEED 90°).
• COMBINING DUCTS WITH DIFFERENT CROSS-SECTIONS IS NOT RECOMMENDED (E.G. Ø15 CM WITH Ø12 CM).
• ENSURE THAT THE SIZE OF THE SUCTION OPENING IS AT LEAST AS BIG AS THE SIZE OF THE AIR EXHAUST. THIS WILL PREVENT NEGATIVE PRESSURE AND ENSURE PROPER FUNCTIONING OF THE HOOD.
• IF THERE ARE ANY OPEN-FLAME APPLIANCES IN THE ROOM (E.G.: SOLID AND LIQUID FUEL COOKERS, FIREPLACES, HEATERS, ETC.). MAKE SURE THERE IS AN ADEQUATE SUPPLY OF FRESH AIR.

CAUTION!
USE SCREWS AND FASTENERS APPROVED IN THE MANUAL TO AVOID THE RISK OF ELECTRIC SHOCK. The minimum distance between the surface of the cooker and the lowest part of the range hood (see figure below) must be at least 40 cm for electric cookers and 50 cm for gas cookers. If the cooker manual indicates a greater distance than specified above, follow the instructions in the cooker manual.Installation of the product is shown in Figures 7 – 18. During installation, follow the general regulations concerning air extraction.

OPERATING MODE WITH EXHAUST OR CLOSED AIR CIRCULATION

In case of operation with air extraction (Fig. 4), the vapours are exhausted to the atmosphere through the ventilation duct by means of the extraction system.With the air recirculation mode, the vapours are freed from grease particles and odours and blown back into the kitchen (Fig. 5). In order for odors to be absorbed by the hood, an activated carbon filter is mandatory. This mode of operation is only used when there is no possibility of vapour escaping to the outside.

PREPARATION BEFORE HOOD INSTALLATION

• Check whether the dimensions of the purchased product are suitable for the selected place of installation.
• Disconnect and remove (if possible) any appliances in the installation space to facilitate access to the ceiling or wall where the hood will be installed. If this is not possible, secure these elements.
• Check whether there is a socket near the hood installation space and whether it is possible to connect the hood to a ventilation duct for fume extraction.
• Make sure there are no lines of electric and plumbing installations in places where holes will be drilled.
• Prepare the following tools: tape measure, pencil, drill/driver, drill bit, screwdriver, level.
  CAUTION!
  THE CHOICE OF DOWELS AND SCREWS DEPENDS ON THE MATERIAL OF THE CEILING AND IS ALWAYS SELECTED INDIVIDUALLY BY THE INSTALLER.
  CAUTION!
  TAKE CARE NOT TO SCRATCH THE HOOD.

WERENISO ISOLA 39

HOOD INSTALLATION

1. Remove the grease filter, then disconnect the turbine plugs A and the hood power plugs B.

2. Remove the 4 screws securing the lower part of the extractor hood.

3. Disassemble both parts as shown on the picture.

4. Unscrew the top tube from the frame.

5. Separate the frame into two parts.

6. Drill four holes above the hob and place four pegs and two screws in them diagonally – just like the beans in the rack. Tighten the screws leaving 5mm clearance between the screw head and the ceiling. Place the frame with the beans on the screws and twist so that the heads of the screws move to the narrower part of the beans – this will suspend the frame and you can proceed to screw in another two screws. Finally, tighten all four screws. CAUTION!
   IN THE CASE OF SUSPENDED CEILINGS, A REINFORCED STRUCTURE/FRAME MUST BE PREPARED IN ADVANCE. IT IS NOT POSSIBLE TO FIT THE HOOD TO A LIGHTWEIGHT SUSPENDED CEILING STRUCTURE AS THERE IS A RISK OF  IT BREAKING AND FALLING.

7. Join the two parts of the frame together, establishing the total height of the extractor hood.
   Then screw the previously dismantled lower part of the hood to the hanging frame.

8. Connect the air extraction pipe to the hung extractor hood body. Then connect the power cord to the power supply.

9. Attach and screw on the previously dismantled top tube.

10. Slide the lower part of the extractor hood. Open the lid and tighten the 4 mounting screws.

11. Remove the grease filter from the extractor hood. Then connect the plugs of turbine A and hood power plugs B.

12. Fit the grease filter and close its cover. CAUTION!
    AFTER INSTALLATION, REMOVE ALL PROTECTIVE FILMS FROM THE HOOD AND ITS COMPONENTS (FILTERS, GRILLES, ETC.)

CARBON FILTER

The hood can be fitted with a charcoal filter. The filter should only be used when the hood is not connected to the ventilation duct. Place the filter in the frame above the anti-grase filter as shown in Fig. 19. The filter should be replaced every 3-6 months. CAUTION!
DO NOT WASH OR REUSE THE CARBON FILTER.

LED STRIP REPLACEMENT

The installation must be carried out by qualified personnel

POWER SUPPLY CONNECTION

The supply voltage must correspond to the voltage indicated on the identification plate placed inside the hood. If the hood is equipped with a plug, insert it in an accessible socket compliant with the applicable regulations, as it shows is in Fig. 14. If the hood is not equipped with a plug, the installation should be carried out by a certified specialist (e.g. an electrician).

CLEANING AND MAINTENANCE

Before performing any maintenance operations, unplug the device from the socket. Use mild detergents for cleaning. Do not use abrasive cleaning products. The hood should be cleaned at least once a month or every 35 hours of operation. DO NOT USE ALCOHOL-BASED CLEANING AGENTS. Inox parts should be cleaned with special product (e.g. BERNER).

ANTI-GREASE FILTER

The hood is equipped with an aluminium filter which partially traps grease particles. You can wash the filter manually by immersing it for 15 minutes in 40-50ºC water with dishwashing liquid.
After 15 minutes, wash and rinse the filter thoroughly. Dry well before placing it back in the hood.
You can also wash it in a dishwasher. After cleaning, you may notice a slight discolouration of the filter, which does not affect its properties. A regularly cleaned filter will help to maintain the efficiency of the hood and prevent the risk of fire.

SETTINGS (BUTTONS ON THE HOOD OR REMOTE CONTROL)

LED display
The selected speed level (1,2,3,4) will be shown on the display . 3
Speed adjustment
Pressing the minus „–” button 2 will decrease the speed of the turbine.
Pressing the plus „+” button 4 swill increase it.
Switching the hood motor on and off
The hood motor can be started in 3 ways:

1. Pressing the 1 button – the motor will switch on at the same speed level at which it was 1 switched off.
2. Pressing the minus „–” button 2 – the motor will switch on at the minimum speed level.
3. Pressing the plus „+” button 4 – the motor will switch on at the maximum speed level.

Switching the lighting on and off 5
To turn the hood lighting on, press . Pressing the button again turns the lighting off.

Timer 15 minutes
The control panel of the hood is equipped with a turbine timer, which turns it off 15 minutes af- ter the timer is activated. In order to activate the timer, the hood turbine must be running at any speed. The timer is activated / deactivated by pressing the button on the remote control until 6 the dot starts blinking on the display in the bottom right corner.
The metal filters should be cleaned more frequently, if required!
The control panel of the hood is equipped with a functionality that automatically switches off the turbine if the control panel has not been used for 2 hours.

IN CASE OF PROBLEMS

The range hood does not function at all:

• Check whether the fuse in the domestic installation is not pulled out.
• Check if the thermal cutout of the motor has not been activated due to high temperature. If this is the case, switch off the device and wait for about 20 – 30 minutes until the temperature returns to normal; then switch the hood on again.
• Make sure that the plug is inserted in the socket.
• Remove the plug to restart the device. Wait for about 15 – 20 seconds and then plug it back in.
  Alternatively, you can also pull out the fuse for that time and then put it back in.

Insufficient efficiency / noisy operation:

• Check whether the cross-section of the ventilation duct is sufficient and whether it has not too many bends and sharp angles.
• Check if the return flap (if optionally installed) is not jammed in the ventilation duct.
• If the ventilation duct is equipped with a swinging grille, remove it.
• Make sure that the metal filters are clean.
• Replace the active carbon filter if it is older than 6 months (only in recirculation mode).
• Check whether the amount of air extracted from the kitchen is balanced by sufficient fresh air supply (to prevent negative pressure).
• Check whether the ventilation chimney is not obstructed.
• Excessively low atmospheric pressure may reduce the performance of the hood. Verify the functioning of the hood again on another day.

ENERGY LABEL

The above energy label is only an example. The actual data can deviate from that specified above in any other model.

REDUCING THE IMPACT OF COOKING ON THE ENVIRONMENT

• In order to reduce energy consumption, cover pots and pans with lids while cooking.
• Keep the aluminium filters clean (the recommended cleaning schedule for the filter is at least once every 35 hours).
• Keep the ventilation ducts unobstructed.
• Always set the turbine speed during cooking to the minimum required level, allowing for fume extraction at the current cooking intensity.

SERVICE AND MAINTENANCE

If, despite our strict quality control, you find any irregularities in the operation and functioning of the purchased device, please contact our service department to receive professional assistance of our team.
The service support is available Monday to Friday from 9.00 am to 5.00 pm at: +48 13 49 27 560
extension: 3 and +48 609 055 660 or by email at: serwis@lanilia.pl.
Before connecting the service, please take down the following details of your device:
Type:…………………………………
Seria-Nr:……………………………..
You can find this information on the identification plate. The plate is located inside the hood and is visible after removing the metal filters.

LANILIA

Modell| WERENISO ISOLA 39
Engine power| 275 W
Lighting power| 2X5 W
Total power| 285 W
Supply Voltage / frequency| 220-240V/50Hz
Outlet diameter| Ø15 cm
Seria-Nr| 7350001
LANILIA MAX Ul. Maków 10 38-500 Sanok|

The identification plate shown in the figure above is only an example. The data may differ for other models.
To request a hood repair, you can use the form available at www.lanilia.pl/serwis/.

TROUBLESHOOTING

hours of operation, the display indicates that the anti-grease filter needs to be cleaned or replaced.| Press and hold down for approx. 6s the „-” button on the panel. Clean the
filter or replace it with a new one.
The display only shows the „-.” sign (minus and dot in the lower right corner), the hood does not start
when switched on.| The touch panel is locked (this is a function used to facilitate cleaning of the hood).| To deactivate the lock, press and hold the
on/off sign for approx. 10s.
No sign appears on the display, the hood does not respond to the buttons.| The control panel may be frozen.| Disconnect the hood from the power supply for approx. 15 seconds and then
switch it on again.
The display shows the sign of one of the speed levels and the hood does not react to the buttons.| The control panel may be frozen.| Disconnect the hood from the power supply for approx. 15 seconds and then
switch it on again.
The hood turbine switches off after
15min. of operation and the display blinks with, for instance „1” (the number of the current speed level and a dot in the lower right corner of the display.| The automatic timer of the control panel has been activated.| To deactivate the timer, press the plus sign for about 10 seconds or switch off the device.
Number „4” on the display is blinking, and after 5 min. the speed level changes to 3.| The hood is equipped with a turbo mode, which automatically changes to level 3 after 5 minutes of operation to save energy.| The turbo mode should only be used for intensive cooking.
The hood can only be operated using
the control panel, it does not react to the remote control.| The battery in the remote control is flat or the remote is too far from the device.| Replace the battery.
Low suction efficiency.| The filters may be dirty.| Wash or replace the anti- grease filter.
Replace the carbon filter (if any).
One or more light bulbs are not lit.| Burnt halogen or LED bulb.| Replace the bulb in accordance with the user manual.
The hood generates excessive noise and vibration.| The reason may be incorrect installation of the hood to the
wall or kitchen cabinet. Not all of the screws required were
screwed in, or the screws were not tightened enough, leaving
clearance.| The hood must be fixed to the wall or cabinet using the number of screws
indicated by the manufacturer. After adjusting the position of the hood
vertically and horizontally, tighten all the mounting screws.

• applies to range hoods with touch control
  If after following the above-mentioned guidelines the problem is still not solved, contact an authorised household appliance repair service.
  Do not try to repair the hood yourself. A list of authorised repair centers is provided on the warranty card and on the website.

WARRANTY

Within the period of 2 years from the date of purchase of the product, LANILIA undertakes to cover all repair costs for faults which are obviously caused by manufacturing defects. The warranty does not cover burnt bulbs, fuses and filters, as well as any damage due to faulty installation and ventilation system.
In addition, the warranty does not apply in the following cases:

• Application in the catering industry.
• Application for any other purposes than household use.
• Use of the device not in accordance with the operating instructions and its intended purpose.
• Circumstances beyond the control of the manufacturer, including, without limitation: uncontrolled power surge, flooding, obstruction of the ventilation duct.
• Apparent mechanical damage after installation of the device.

CAUTION!

• ANY PRODUCT WITH MECHANICAL DAMAGE, WHICH HAS NONETHELESS BEEN INSTALLED, WILL NOT BE REPLACED! BEFORE INSTALLATION OF THE DEVICE, UNPACK IT AND CAREFULLY INSPECT IT FOR ANY MISSING COMPONENTS OR DAMAGE. ANY VISIBLE EXTERNAL DAMAGE CLAIMED AFTER INSTALLATION IS EXCLUDED FROM THE WARRANTY.
• LANILIA MAX SHALL NOT BE HELD LIABLE FOR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY PERSONS, ANIMALS OR OTHER OBJECTS AS A RESULT OF NON-COMPLIANCE  WITH THE INSTRUCTIONS IN THIS MANUAL, IN PARTICULAR THOSE CONCERNING INSTALLATION, OPERATION AND MAINTENANCE OF THE DEVICE!

Company Headquarters
LANILIA ul. Maków 10
38-500 Sanok Poland
Tel.: +48 13 49 27 560
www.lanilia.pl
e-mail: biuro@lanilia.pl
Service:
Phone: +48 13 49 27 560 extension 3
Mobile phone.: +48 609 055 660
e-mail: serwis@lanilia.pl
www.lanilia.pl/serwis/ 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>