Zhejiang Dusun Electron DSRO-010 Bluetooth and Voice Control User Manual
- June 8, 2024
- Zhejiang Dusun Electron
Table of Contents
Zhejiang Dusun Electron DSRO-010 Bluetooth and Voice Control
STREAMING PROVIDER APPS HOTKEY PROGRAMMING
STEP 1: Press and hold the „ 1“ & „ 3“ keys simultaneously for 6 seconds
to enter App programming mode. The LED will light up.
STEP 2: Enter the 3 digit code using the cursor key
- OK for: „0“,
- Up for „1“,
- Down for „2“,
- Left for „3“,
- Rightfor „4“
The LED flashes for 2 seconds and then goes off if the programming was successful
TABLE
REMOTE CONTROL
- Power
- Mute
- Voice Control
- Numeric- & Colour Keys
- Multiview mode (short press)
- Frame mode (long press >3s)
- Cursor
- Back
- Play/Pause
- Home
- Volume +/-
- Channel List
- Program Up/Down
- Apps Hotkeys
PAIRING
STEP 1: Press and hold „BACK“ and „PLAY/PAUSE“ simultaneously for 3
seconds to enter the pairing mode.
The LED will flash while the remote control is in pairing mode (30 seconds )
Step 2: As soon as the remote control is in pairing mode your TV
automatically starts the pairing routine and displays the pairing status on
the screen
LED lights up continuously for 3 seconds and then goes off : Pairing
successful LED blinks and goes off after 30 seconds: Pairing unsuccessful
- Press and hold „BACK“ and „PLAY/PAUSE“ simultaneously for 3 seconds to enter the pairing mode.
- The LED will flash while the remote control is in pairing mode (30 seconds )
- As soon as the remote control is in pairing mode your TV automatically starts the pairing routine and displays the pairing status on the screen.
- LED lights up continuously for 3 seconds and then goes off : Pairing successful
- LED blinks and goes off after 30 seconds: Pairing unsuccessful
Scope of supply
Declartion of Conformity
By using the CE mark, CLASSIC Service Parts GmbH declares that the product
complies with the requirements and guidelines of European regulations.
Recycling guide
According to the European WEEE Directive, electrical equipment must not be
disposed of in the household waste. By law, you as the end user are required
to return all waste electrical/electronic equipment and batteries either to
the manufacturer, the point of sale or to a public recycling center.
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
NEED HELP
- Classic Service Parts GmbH
- Rodensteiner Str. 40
- 64385 Reichelsheim
- www.classic-serviceparts.com
- UK Support:
- TW Electronics (Newbury) Ltd.
- www.twelectronics.co.uk
- WEE-Reg.-Nr. DE91546912
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>