XRONG HY1898BT Bluetooth Music Player Instructions
- June 5, 2024
- XRONG
Table of Contents
XRONG HY1898BT Bluetooth Music Player Instructions
Description
-
USB Socket
-
AUX Socket
-
Press for a longer time-Increase Volume
-
Press for a longer time- Decrease Volume
-
Pause
-
Press for a shorter time- Muisc
-
Press for a shorter time- SPK
-
Electricity/Display
-
Power +12V
-
Speaker
-
Connection of Touch Spot
-
Connection of Music
-
Connection of Loudspeaker
(Connect with power, and pressing any button can disrupt auto startup engine sound.)
After the auto startup engine sound, it will get into music mode: there will be one voice said ”Music”, the music will not be on automatically by itself.
Instructions of buttons
- Electricity/Display: Show current mode/electricity/music
- USB Card Socket: Can support 16G maximum, otherwise can not work.
- AUX Socket: Can connect with mobile phone lines.
- Music Bu on: Press shorter—Music, Press Shorter again—next track;
- Loudspeaker: Press shorter—Loudspeaker on
- Music: Press shorter— Music on
Function Instruction
Power on, and press any bu on can disrupt auto startup engine sound.
After the auto startup engine sound, it will get into music mode: there will be one voice said ”Music”, the music will not be on automatically by itself.
Bluetooth Display Name on this devise: Bumper Car
When auto switch to Bluetooth mode, turn on the bluetooth on mobile and start to search and connect with Bumper Car . There will be remind voice when connection successful.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receivingantenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the
US/Canada.
This device is intended only for OEM integrators under the following conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna,
As long as the conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
Important Note:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID cannot be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following”
Contains FCC ID: 2AVDK-HY1898BT”
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
Limited module procedures
This module is Limited single modular without shielding, host manufacturer have to consult with module manufacturer for the module limiting conditions when integrate the module in the host. module manufacturer should reviews detailed test data or host designs prior to giving the host manufacturer approval.
Trace antenna designs
Not applicable
RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Antennas
This radio transmitter 2AVDK-HY1898BT has been approved by Federal
Communications Commission to operate with the antenna types listed below, with
the maximum permissible gain indicated.
Antenna types not included in this list that have a gain greater than the
maximum gain indicated for any type listed are strictly prohibited for use
with this device.
Antenna No.| Model No. of antenna:| Type of antenna:| Gain of the antenna
(Max.)| Frequency range:
---|---|---|---|---
Bluetooth| /| PCB Antenna| 2.0dBi for 2402-2480MHz;
Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID: 2AVDK-HY1898BT “.
Information on test modes and additional testing requirements
Host manufacturer which install this modular with single modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C:15.247 and 15.209 requirement, only if the test result comply with FCC part 15.247and 15.209 requirement, then the host can be sold legally.
Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>