FIELDMANN FZP 4216-B Chainsaw Instruction Manual

: June 5, 2024
: FIELDMANN

FIELDMANN FZP 4216-B Chainsaw Instruction Manual

GENERAL SAFETY INSTRUCTIONS

Important safety notice

Carefully unpack the product and take care not to throw away any part of the packaging before you fi nd all the parts of the product.
Store the product in a dry place out of reach of children.
Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical shock, a fi re and/or serious injuries.

Packaging

The product is packed in a package that prevents damage during transport. This package is a resource and so can be handed over for recycling.

User’s manual

Before you start working with the machine, read the following safety and usage instructions. Acquaint yourself with the operating elements and the correct use of the machine. Keep the user’s manual in a safe place where it can be easily retrieved for future use. Save the original packaging, including the internal packing material, warranty card and proof of purchase receipt at least for the duration of the warranty.
If you need to ship this machine, pack it in the original cardboard box to ensure maximum protection during shipping or transport (e.g. when moving or when you need to send this product for repair).

NOTE: If you hand over the power tool to somebody else, do so together with this user’s manual.
Following the instructions in the included user’s manual is a prerequisite for the proper use of the power tool.
The user’s manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not following the instructions in this manual.

EXPLANATION OF INSTRUCTION LABELS ON THE MACHINE

Before using the power tool, carefully read the user’s manual.

When operating the power tool, wear protective aids such as safety glasses, earmuffs, etc.

Always use two hands when operating the chain saw.

INSTRUCTION LABELS While working use protective gloves.

INSTRUCTION LABELS Use solid insulating work footwear.

Attention! Danger of kickback

Warning! Attention!

SAFETY INSTRUCTIONS

ATTENTION! The safety instructions in this user’s manual are marked with the symbol containing critical points, which one needs to pay attention to when operating the power tool to prevent serious or fatal injuries.
Please carefully study the instructions and adhere to them.

ATTENTION! This symbol indicates instructions that must be adhered to in order to prevent accidents that could result in serious or fatal injuries.

NOTE: This symbol indicates a tip or instructions useful when operating the power tool.

Before using the power tool

Before using the power tool, carefully read the user’s manual.
Do not use the power tool if your are under the infl uence of alcohol or narcotics, if you are tired or exhausted.
Do not use the power tool if your are taking medication, which could affect or limit your decision-making abilities for safe operation of the power tool.
Do not use the power tool indoors, the emitted gases contain damaging carbon monoxide.
Never use the power tool under the conditions listed below:
- If the work surface is slippery or if weather conditions do not permit you to maintain a stable stance while operating the power tool.
- If it is dark, heavy fog or under poor weather conditions, which limit visibility of the work area.
- During rain, during a storm or in strong winds or under conditions that could be dangerous when operating the power tool.
If you are using the chain saw for the fi rst time, please consult with an experienced user before starting work.
Tiredness or physical exhaustion may lead to inattentiveness, which may result in serious injury
Limit the operating time of the power tool to approx. 10 minutes per single use and try to rest for approximately 10-20 minutes between work sessions. Limit the total amount of work per day to approximately 2 hours.
Make sure that you have the user’s manual at hand in case you need to use it.
If you sell, loan or handover the power tool, make sure that you include the user’s manual.
Never allow children or other persons that are insuffi ciently acquainted with the user’s manual to use this power tool.

Safety of the operator, work equipment and clothing

When operating a chain saw, you should wear the following work clothing and protective aids:
- Helmet
- Safety glasses or protective face shield
- Work gloves
- Anti-slip work boots
- Earmuffs
Furthermore, you should also have
- The included tools
- Suffi cient supply of fuel and chain lubricating oil
- Accessories for designating the work area (rope, warning signs)
- Whistle (to call for help)
- Hand saw or axe (to remove potential obstacles)
When working, never wear loose clothing, jewellery, that could become caught by the chain saw. Do not wear sandals when working, do not work barefoot.
Check the work area, the item being cut and the cutting direction. Remove obstacles.
Never commence work if the work area is not cleared, if you do not have a stable stance and if you do not have a planned escape route in the event of a falling tree.
Pay increased attention and keep passers-by and pets away from the work area at a distance of at least 2.5 times the length of the item being cut.
Check for damaged, worn out or missing parts of the power tool. Never use the power tool if it is damaged, incorrectly adjusted or incomplete.
Check that the chain stops turning when the throttle trigger is released.
Keep the handles dry, clean and free of oil and fuel stains.
Do not touch the muffl er, spark plugs or other metal parts of the engine when the power tool is running or immediately after it is turned off – there is a risk of burns or injury by electrical shock.
Pay exceptional attention when cutting thin branches or trunks because fragile material may become caught in the chain and fl ung towards the operator and may thus cause a loss of balance.
When cutting tensioned branches keep in mind that they will fl ing out when the wood fi bres are cut and the tension is released.
Check for and remove dry branches that could come loose from the falling tree.
Make sure that the power tool is turned off when you put it down.

CAUTION danger of kickback! Kickback may occur when the nose of the guide bar comes into contact with an item or if the material being cut clamps the chain in the cut. During contact with the item, the chain saw may be fl ung with the guide bar moving up and back towards the operator. A clamped chain may result in a fast backward movement of the guide bar towards the operator. Both these reactions may lead to a loss of control over the chain saw and subsequent serious injuries.

Do not rely only on the chain saw’s safety features. As the operator of the chain saw, you must constantly adhere to multiple rules to avoid injuries or damages.
If you are acquainted with the kickback principle, you can reduce or eliminate the moment of surprise.
Unexpected reactions result in accidents.
If the engine is running, hold the chain saw with both hands with the right hand on the rear handle and the left hand on the front handle. Firmly grasp the handle with the thumb going around towards the fi ngers.
A firm grip helps limit kickback and to keep the chain saw under control.
There must be no obstacles in the work area. When working with the chain saw, the loose end of the guide bar must not touch a branch, trunk or another obstacle.
Cut with the engine running at high speed.
A stable stance must be maintained at all times when cutting, do not cut above shoulder height.
Adhere to the instructions of the manufacturer for lubricating and sharpening the chain.
Only use spare chains and guide bars specifi ed by the manufacturer or their equivalents.

Instructions for handling fuel
The engine of the power tool is designed to use a highly fl ammable fuel mix. Never store fuel containers or refi ll fuel in the vicinity of an open fl ame, wood stove, electrical lines, welding work or other sources of heat or fl ame, which could lead to ignition.

Smoking is forbidden when operating the power tool and when refi lling fuel.
When refi lling fuel, make sure that the power tool is off and that there is no open fl ame in the vicinity.
If the power tool is sprayed with fuel, use a dry cloth to wipe away the stains.
After refi lling fuel, screw on the fuel tank cap and take the power tool at least 3 m away from the place where it was refi lled and then start it up

MACHINE DESCRIPTION AND INCLUDED CONTENTS

MACHINE DESCRIPTION

Description of the power tool (see Fig. 1)

Throttle safety switch
Throttle trigger
Main power switch
Fuel tank cap
Oil tank cap
Front handle
Chain
Guide bar
Safety brake
Starting cord handle
Air filter cover screw
Choke lever

Included contents: Petrol chain saw, 405 mm guide bar, chain, plastic guide bar cover, calibrated fuel mixing container, tool set with file.

INSTALLING THE BUMPER SPIKES, GUIDE BAR AND CHAIN

ATTENTION! Always wear protective gloves when installing and inspecting the chain to prevent injury from the sharp cutting edges on the chain.

Installing the bumper spikes (Fig. 2)

Using the included hex key and screw, attach the bumper spikes, see fi gure. For correct attachment, it is necessary to screw out the exhaust cover bolt and after the installation to screw it back in. This bolt serves to attach both the bumper spikes and the exhaust cover.

Installing the guide bar and chain

The safety brake lever (Fig. 1 point 10) must be disengaged (pull it towards the top handle)
Loosen two nuts and take off the sprocket cover (Fig. 3, point 1).
Seat the chain on to the guide bar and then thread on to the sprocket (pinion). At the same time, hold the chain on the guide bar.

ATTENTION! The chain tensioning pin must fit into the hole in the guide bar (Fig. 4, point 2). The position of this pin can be adjusted using the chain tensioning screw (Fig. 5)

Installation

Put the sprocket cover back. Do not fully tighten the screws, tighten by hand only, to make it possible to
tension the chain.
Tension the chain using the tensioning screw (Fig. 5) and then tighten the sprocket cover nuts using the
included tubular wrench

ATTENTION! The chain is correctly tensioned if it is possible to lift chain off the guide bar and its height in the horizontal position in the middle of the guide bar is 3 to 4 mm.

FUEL AND CHAIN LUBRICATING OIL

Filling the oil tank

ATTENTION! A new chain requires a certain running-in period, which is usually 5 minutes. The lubrication of the chain is very important during this phase. After this running-in period, check the chain tension and readjust if necessary.

The oil tank on the supplied chain saw is empty. Fill this oil tank with oil prior to fi rst use of this chain saw.
Only use oil specifi ed for total-loss lubrication
Screw off the oil tank cap (fi g. 6, point 2).
Pour the oil into the tank (take care to prevent the oil from becoming dirty while fi lling the tank).
Screw on the oil tank cap

ATTENTION! Do not use oil that has already been used or processed because this could damage the oil pump.

Mixing the fuel mix

ATTENTION! Never pour fuel into the fuel tank in a closed and unventilated location.

ATTENTION! Do not pour fuel in the vicinity of an open fl ame or a source of sparks.

ATTENTION! Do not overfi ll the petrol tank. Before starting the engine, make sure that all spilt fuel is wiped away.

ATTENTION! If the engine is hot, DO NOT POUR IN FUEL.

For this type of two-stroke engine a mixture of lead-free petrol and two-stroke engine oil is used at a ratio of 25 : 1.

ATTENTION! A fuel mix that is mixed at a ratio other than 25 : 1 may damage the engine. Make sure that this fuel mix is mixed correctly.

When mixing petrol with two-stroke engine oil, use only petrol containing NO ETHANOL or METHANOL (types of alcohols).
Use quality petrol with an octane number of 95 or higher. This will help prevent possible damage to the fuel system and other parts of the engine.
We recommend the use of the calibrated container supplied with the chain saw for mixing the fuel mix.
DO NOT MIX THE PETROL AND OIL DIRECTLY IN THE FUEL TANK.
Screw off the fuel tank cap (Fig. 6, point 1) and pour in the fuel. Then screw the cap back on.

Storing fuel
Only store fuel in a clean, safe and approved canister.
Inform yourself about and adhere to local directives related to the type and storage of canisters fi lled with fuel.

ATTENTION! Fuel for two-stroke engines may separate. Prior to every use, thoroughly shake the canister with fuel.

ATTENTION! Stored fuel ages. Do not mix more fuel than you expect to consume within one month.

PREPARING FOR OPERATION

IMPORTANT: Follow instructions for preparing the fuel mix! Not following these instruction may damage the engine! Do not use fuel that has been stored for longer than two months. A fuel mix stored for longer than two months will cause problems at start up and lower engine performance. If the fuel mix is stored for longer than two months, it should be removed and new fuel must be used.

Check for damaged, worn out or missing parts of the power tool. Never use the power tool if it is damaged, incorrectly adjusted or incomplete.
Check whether any screws, nuts and installation elements are loose. Tighten any loose screws.
Check whether the air fi lter is dirty. Prior to starting work, remove all dirt from the air filter.
Check that the chain is tensioned. You can lift a correctly tensioned chain in the middle of the guide bar in the horizontal position by 3 to 4 mm
Keep the handles dry, clean and free of oil and fuel stains.
Check the fuel tank for leaks.
Check the work area, the item being cut and the cutting direction. Remove obstacles.
Never commence work if the work area is not cleared, if you do not have a stable stance and if you do not have a planned escape route in the event of a falling tree.
Pay increased attention and keep passers-by and pets away from the work area at a distance of at least 2.5 times the length of the item being cut.

Chain brake (Fig. 1, point 10)

This chain saw is equipped with an automatic brake that stops the chain in the event of kickback. The brake is engaged automatically by inertia acting on the ballast located under the rear cover. This brake can be operated manually by tilting down the front protective frame towards the guide bar.
The brake is disengaged by pulling the front protective frame back towards the chain saw handle.

ATTENTION! Before every use, check that the chain brake is in working order in the following manner.

Checking the working order of the brake

Place the running chain saw on to the ground and for 1 to 2 seconds leave it at full speed.
Push the brake lever (Fig. 1, point 10) forward. The chain should stop immediately.

ATTENTION! If the chain stops slowly or does not stop at all, do not use the chain saw and contact an authorised service centre.

If you wish to disengage the brake, pull the brake lever towards the top handle so that you hear the typical click.

ATTENTION! Check that the chain brake is in order. A correctly functioning chain brake will protect you against potential injury, which could result from kickback.
If the brake is not working properly, have it adjusted or repaired at an authorised service centre.

TURNING THE CHAIN SAW ON AND OFF

WARNING

Prior to starting the engine, make sure that the chain moves freely along the guide bar and is not touching any foreign objects.
When the engine is idling, the saw chain must not be turning. Otherwise, contact an authorised service centre to perform an inspection and remedy the problem.
Prior to starting the engine, make sure that the throttle trigger moves freely.

ATTENTION: Exposure to vibrations may damage the health of persons that suffer from circulatory or nerve system problems. If any physical problems become evident, such as desensitisation, loss of sensitivity, loss of usual strength or changes in skin colour, please contact a doctor. These systems usually manifest themselves on fi ngers, hands or wrists.

Starting a cold engine

Set the power switch to the “I” position. (see Fig. 7, point 1)
Pull out the choke lever (Fig. 7, point 3) to the “OFF” position (=air supply turned off, i.e. choke turned on).
Place the chain saw fl at on the ground so that it is stable and pull on the handle of the starting cord until the engine rotates (the engine will show signs of attempting to start) (Fig. 8).
At this point, push the choke lever (Fig.7, point 3) downwards to the “ON” position (=air supply turned on, i.e. choke turned off) and start the engine by repeatedly pulling on the starting cord.
ATTENTION! Spinning the engine for too long with the choke lever in the OFF position will result in flooding of the engine and problems with starting it up.
Prior to starting work, leave the engine to warm up for a few minutes to get up to operating temperature.

Starting a warm engine

Set the power switch (Fig. 7, point 1) to the “I” position.
Pull on the handle of the starting cord until the engine starts up (Fig. 8). DO NOT USE THE CHOKE!

ATTENTION! In the event that the fuel in the fuel tank was completely used up, after pouring in fuel, repeat the steps for STARTING A COLD ENGINE.

Speed control

To increase speed, fi rst use the palm of your hand to push down the throttle safety switch (Fig. 7, point 4) and then use your fi nger to pull on the throttle trigger (Fig. 7, point 5)
To lower the speed, release the throttle trigger

Stopping the engine

Release the throttle trigger (Fig. 7, point 5) and switch the power switch (Fig. 7, point 1) to the “0” position.

WARNING
The engine exhaust fumes contain chemical substances that are damaging to health. Never inhale these fumes. Always start the chain saw outdoors.

Checking chain lubrication

ATTENTION! Adhere to safety provisions and prevent the guide bar from coming into contact with the surface of the terrain.
Use this power tool safely and maintain a minimum distance of 20 cm from the ground.

Before starting work, check the chain lubrication and the amount of oil in the oil tank. Start the chain saw and hold it above the ground. If you see a growing oil stain then chain lubrication is working properly. If there are no oil stains on the ground, adjust the lubrication strength on the underside of the chain saw (Fig. 9)
If even then, the chain is not suffi ciently lubricated, clean out the oil outlet (under the sprocket cover), the top chain tensioning hole and the oil lines, or contact an authorised service centre if necessary.

ADJUSTING THE CHAIN TENSION

ATTENTION! Due to the effect of higher temperatures, during operation the saw chain has a tendency to lengthen. A longer chain becomes loose and could slide off the guide bar.

Loosen the sprocket cover fastening nuts.
Make sure that the chain is seated in the guiding groove of the guide bar.
Use a screwdriver to turn the chain tensioning screw (Fig. 5). Turn the tensioning screw until the required tension is achieved (you should lift the chain in the middle of the guide bar in the horizontal position to a height of 3 to 4 mm).
Firmly tighten the guide bar fastening nuts.

ATTENTION! Do not tension the chain excessively. Excessive tension of a warm chain may result in excessively tension when it cools down.

CUTTING

ATTENTION! Before proceeding, please read the chapter “Safety instructions”. We recommend that you gain experience by cutting smaller logs. In this way you will also get to know the chain saw.

Always adhere to safety instructions. The chain saw may only be used for cutting wood.
It is forbidden to cut any other materials. Vibrations and kickback differ for various materials. Do not use the chain saw as a lever for lifting, moving or splitting material. It is forbidden to attach any parts or jigs other than those specifi ed in the technical documentation.
It is not necessary to push the chain saw into the cut. When the engine is running at full speed, push the chain saw down lightly.
If the chain jams in the cut, do not attempt to free it by pulling, rather stretch open the cut using a wedge or crowbar.

Safety brake (protection against kickback)

This chain saw is equipped with an automatic chain brake that, if it works correctly, immediately stops the chain in the event of kickback. It is necessary to check the working order of the chain brake before every use of the chain saw. Run the chainsaw at full speed for 1 – -2 seconds and then tilt the front protective cover.
The chain must stop immediately even when the engine is running at high speed. If the chain stops slowly or does not stop at all, please contact an authorised service centre.
It is extremely important to check the working order of the chain brake and the sharpness of the chain before every use to ensure that the necessary level of safety in the event of a kickback is maintained.
Removing safety accessories, incorrect maintenance or when using unsuitable guide bars or chains may, in the event of kickback, result in serious injuries.

Felling trees

Felling trees

Decide about the direction in which the tree will fall, respecting the wind direction, incline angle of the tree and location of the branches, and consider all other factors before cutting.
The area around the tree must be clear, without obstacles, and must enable a stable stance. The escape route must be passable.
Cut a wedge into one third of the tree’s diameter on the side to which the tree should fall. (see Fig. Felling, point 1)
From the opposite direction perform a separation cut at a level above the wedge cut. (see Fig. Felling, point 2)
The tree will fall in the direction towards the wedge cut. (see Fig. Felling, point 3)

ATTENTION! When felling trees, inform other people in the area about the potential danger.
Felling trees requires experience and we do not recommend performing this task without the necessary experience.

Cutting logs

ATTENTION! Always maintain a stable stance. Do not step on logs.

ATTENTION! Before starting work, check that all components are in their place and that all nuts and bolts are tightened.

The log being cut may roll away. Especially when cutting on a slope, always stand above the log being cut.
Prevent kickback of the saw by following the instructions in chapter “Safety instructions”.
Before starting work, assess the direction of the force causing the cut trunk to bend. The fi nal cut needs to always be done from the opposite side of where the bending force is acting to prevent the guide bar from being clamped inside the cut.
Only carry the chain saw with the engine turned off and the guide bar protected by the protective cover.

Log lying on the ground

Cut it halfway through, then roll it over and complete the cut from the other side.

Log above the ground

In part “A” make a cut from below to a third of the log and then complete the cut from above. In part “B” make a cut from above to a third of the log and then complete the cut from below.

Removing a fallen tree

First find out to which side the branch is bent. Then make the initial cut from the side of the bend and then complete the cut from the opposite side.

ATTENTION! A bent branch may spring up

CLEANING AND MAINTENANCE

ATTENTION! Prior to cleaning, inspecting or repairing the chain saw, its engine must be turned off and cold and the spark plug must be removed to prevent accidentally starting the engine.

Maintenance after every use

Remove the guide bar and use a brush to clean away accumulated sawdust from the entire chain saw. Use a spatula or screwdriver to remove stubborn dirt.
Air filter:
Loosen the screw (Fig 1, point 11) and remove the air fi lter cover. Take out the filter insert and use a brush to remove the dust. If the fi lter insert is clogged with dust, dismantle into 2 parts and wash it out in petrol. If you are using compressed air, blow from the inside out.
Lubricating hole:
Take off the guide bar and check the passage of the lubricating hole.
Guide bar:
After taking off the guide bar, remove dust from the grooves and the lubricating hole.
Other parts:
Check for any oil leaks, loose mounts and damaged main parts, particularly in the location where the handles and the guide bar are mounted. Any identified defects must be repaired before the chain saw is used again.

Cleaning the body of the chain saw

Keep the body of the chain saw clean. When cleaning, use a soft cloth dipped in a soap solution. Use this cloth to meticulously clean the body of the chain saw.

Maintaining the guide bar

Maintaining the guide bar

Most problems with the guide bar arise due to uneven wear.
Uneven wear occurs mainly as a result of an incorrectly sharpened chain or an incorrectly set depth gauge.
When the guide bar is worn out unevenly, the guiding groove is widened (see Picture). The result is a rattling chain and rivets falling off. The chain saw cannot be used for straight cuts. In such a case, replace the guide bar for a new one.
Always check the condition of the guide bar before sharpening the chain. Using a worn out or damaged guide bar is very dangerous.
Using a worn out or damaged guide bar will result in damage to the chain. Cutting with such a power tool will also be much more diffi cult and demanding.

Normal maintenance of the guide bar

Remove the guide bar from the body of the chain saw.
Regularly remove sawdust from the guide bar groove. For cleaning use a spatula or a wire.
Clean oily grooves at the end of every work day.
Replace the guide bar if:
- it is bent or cracked
- its groove is very damaged or worn out

NOTE: To replace the guide bar, follow the instruction contained in this user’s manual. You will find the correct guide bar type in the technical specifications.

SHARPENING THE SAW CHAIN

Keep the saw chain sharp. Cutting will be significantly faster and most importantly safer. A blunt saw chain increases wear on the sprocket, guide bar, chain and engine. If you need to push on the saw and only sawdust with a few splinters are produced then this means that the chain is blunt.

For this task, we recommend that you contact an authorised service centre

Equipment necessary for sharpening a saw chain

Round fi le as per technical specifications
Depth gauge
File guide
Vice
Medium-size flat file

Sharpening the teeth on the chain

Use the file guide set at an angle of 30° (mark A, see figure).
SHARPENING THE SAW CHAIN

Set the saw chain tension to the correct level.
Fasten the guide bar in a vice so that you have the chain in a stable position.

NOTE: Do not fasten the chain itself.

Push the round file, inserted in the file guide, into the groove between the top plate and the depth gauge on the chain. The chain should be touching both the top plate as well as the depth gauge (see figure)

NOTE: File in the middle of the guide bar.

NOTE: In the fi gure you can see the position of the fi le guide and the direction for fi ling the teeth on the left side of the chain.

Place the fi le guide at the required angle (mark A, see fi gure). Check that the mark is at 30° on the file guide aligned with the centre of the guide bar. This will ensure that you will fi le at an angle of 30°.
File the tooth in the direction from inside out (in direction B, see fi gure) until it is sharp. File only in this direction.

NOTE: Two to three passes of the fi le should be sufficient to sharpen the tooth.

Filing the depth gauge

As a result of sharpening the teeth on the chain, the depth gauge tolerance is reduced. After every second or third sharpening, it is necessary to adjust the depth gauge setting.

Place the depth gauge adjustment jig (see fi g., point 1) fi rmly on the top edge of two teeth. Make sure that the groove of the jig is in the groove of the depth gauge (see fig., point 2.)
Use a medium-sized flat fi le (see fig., point 3). File the depth gauge (see fig., point 4) to the level of the depth gauge adjustment jig.
Remove the depth gauge adjustment jig. Using a fl at fi le, round the front edge of the depth gauge (see figure). When fi ling, adhere to the prescribed values (see fig., point 5).

NOTE: After the chain has been sharpened by hand several times, have the saw chain sharpened at an authorised service centre or sharpen it on a special sharpening machine.
This will renew the even sharpness of all teeth.

REPLACING THE SAW CHAIN

ATTENTION! When replacing the saw chain, do not clamp the chain saw or the guide bar in a vice.

Always replace the chain if the teeth are excessively worn out and they cannot be sharpened or if the chain snaps. Use only an original spare chain according to the specifications in this user’s manual. When replacing the saw chain, always also replace the cogged wheel of the sprocket. This will ensure the correct position of the chain during movement. (Note: You will fi nd the specifi cations of the correct chain type and the cogged wheel in the technical specifi cations.)

Loosen and remove the bar guide bolt.
Remove the sprocket cover.
Remove the saw chain.
Wind the new chain around the cogged wheel, then along the top groove of the guide bar and around the guide bar nose.

ATTENTION! Check that the saw teeth are facing in the correct direction. Put on the chain so that the teeth on the top side of the guide bar are facing towards the guide bar nose (see figure).

Before placing the sprocket cover into position, check that the chain tensioning pin is inserted into the adjustment hole on the guide bar.
Put the sprocket cover back on to the body of the chain saw.
Fasten the sprocket cover using the guide bar bolt.

ATTENTION! Only tighten the bolt by hand.

Adjust the tension of the saw chain.
Tighten the guide bar bolt.

ATTENTION! Check that you have not placed the saw chain on the guide bar in the opposite direction.
Otherwise, the chain saw will exhibit excessive vibrations and will not cut.

TECHNICAL PARAMETERS

Type FZP 4216 B
Engine 45.0 cm3
Maximum engine power 1.6 kW /7500 rpm
Maximum engine speed with chain 10,500 rpm
Maximum engine speed when idling 3,000 rpm
Guide bar length 405 mm
Chain pitch 0.375 inch
Guiding groove width 1.5 mm
Number of chain links 57 links
File diameter 4 mm
Weight (without the guide bar and chain) 5.5 kg
Dimensions 360 x 160 x 165 mm
Fuel mix (petrol : oil) 25 : 1
Fuel tank capacity 580 ml
Oil tank capacity 250 ml
Chain lubricating oil Total-loss lubrication oil
Chain lubrication system Adjustable automatic pump
Sound pressure level LpA: 96dB (A)
Guaranteed emission level of sound power LwA: 114dB (A)
Vibrations – front handle 8.5 m/s2
Vibrations – rear handle 8.5 m/s2

If you find that the vibrations being transferred to the handle have become noticeably worse compared to the condition when the chain saw was new, check the wear on the silentblocks (rubber coated mounting elements) and if necessary contact an authorised service centre to have them replaced.

ATTENTION! Working with a chain saw with an incorrectly working vibration shock absorption system may lead to health problems.

TROUBLESHOOTING

CAUTION: always turn off the unit and disconnect the spark plug before carrying out the checks recommended in the table, except for the cases where the unit needs to be running.

When all possible causes have been checked and the problem remains unsolved, please contact an authorised service centre. When you identify a problem that is not included in the table, please contact an authorised service centre.
PROBLEM| POSSIBLE CAUSES| SOLUTION
The motor cannot be started or stops several seconds after starting. (Make sure that the switch is in position „I“)|

The spark plug is not ﬁring
The motor is ﬂooded

|

Check that the spark plug is ﬁring. If the spark plug is not ﬁring, repeat the test with a new spark plug (WXL7T).
Take out the spark plug and pull the starting cord several times. Then reinsert the cleaned spark plug and start without using the choke.

The motor starts but does not properly increase its speed or does not run properly at high speeds.| The carburettor must be adjusted.| Contact an authorised service centre to have the carburettor adjusted
The motor does not reach full speed and/or emits too much smoke.|

Check the petrol – oil mixture.
Dirty air ﬁlter.
The carburettor must be adjusted.

|

Only use fresh petrol and oil suitable for two-stroke engines.
Clean it; see instructions in chapter 11.
Contact an authorised service centre to have the carburettor adjusted

The engine starts, works and accelerates, but does not maintain idling speed.| The carburettor must be adjusted.| Contact an authorised service centre to have the carburettor adjusted.
The guide bar and chain heat up and smoke while running|

Empty chain oil tank
Chain is overly tensioned
Lubrication system not working properly

|

The oil tank must be ﬁlled up every time when the fuel tank is ﬁlled.
Tensioning the chain; see instructions in chapter 5.
Allow it to run at maximum speed for 15-30 seconds. Stop and check whether oil is dripping from the tip of the guide bar. If there is oil there, the faulty operation may be caused by a loose chain or damaged guide bar. If there is no oil there, contact an authorised service centre

The motor starts but the chain is not running.
CAUTION: when the motor is running, never

touch the chain

|

Chain brake engaged
Chain is overly tensioned
Guide bar and chain installation
Damaged chain and/or guide bar
Damaged clutch and/or pinion

|

Disengage the chain brake; see chapter 7.
Tensioning the chain; see instructions in chapter 9.
See instructions in chapter 5.
See instructions in chapter 11. and 13.
If necessary, replace it; contact an authorised service centre

DISPOSAL

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS

Dispose of used packaging material at a site designated for waste in your municipality.

The machine and its accessories are manufactured from various materials, e.g. metal and plastic.
Take damaged parts to a recycling centre. Inquire at the relevant government department.

This product meets all the basic requirements of EU directives that apply to it.

Changes in the text, design and technical specifi cations may be made without prior notice and we reserve the right to make these changes.

User s manual in the original language

DECLARATION OF CONFORMITY

Manufacturer:

FAST ell, a.s.
eernokostelecka 2111, 100 00 Praha 10, Czech Republic VAT no: CZ26726548

Product / brand: PETROL CHAIN SAW / FIELDMANN
Type / model: FZP 4216 8
1,8 kW, 45cm3, 10000/min

The product is inline with directives and regulations listed below:
EN ISO 12100:2010 safety of machinery
EN ISO 11681-1:2011 machinery for forestry – safety (LVD/ GS)
EN 15014982:2009 agricultural and forestry machinery — EMC
EN ISO 9207 / 3744 / – 2003/14/EC noise
RoHS 2011/65/EU

CE label: 16

Place of issuance: Prague

Date of issuance: 1.4.2017

Name: Ing. Zdendk Pech Chairman of the Board

Signature:
Icon

Warranty

Warranty Certificate

Serial No. ____

Dealer’s ____

Date of purchase ____

Conditions of guarantee

This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty is limited to the following conditions. Warranty is referred only to the customer goods using for common domestic use. The claim for service can be applied either at dealer’s shop where the product was bought, or at below mentioned authorized service shops. The end-user is obligated to set up a claim immediately when the defects appeared but only till the end of warranty period. The end–user is obligated to cooperate to certify the claiming defects. Only completed and clean (according to hygienic standards) product will be accepted. In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim application till the date of taking over the pro-duct by end-user, or the date the end-user is obligated to take it over. To obtain the service under this warranty, end-user is obligated to certify his claim with duly completed following documents: receipt, certificate of warranty, certificate of installation…

This warranty is void especially if apply as follows:

Defects which were put on sale.
Wear-out or damage caused by common use.
The product was damaged by unprofessional or wrong installation, used in contrary to the appli-cable instruction manual, used in contrary to legal enactment and common process of use or used for another purpose which has been designed for.
The product was damaged by uncaredfor or insufficient maintenance.
The product was damaged by dirt, accident of force majeure (natural disaster, fire, flood, …).
Defects on functionality caused by low duality of signal, electromagnetic field interference etc.
The product was mechanically damaged (e.g. broken button, fall…).
Damage caused by use of unsuitable media, fillings, expendable supplies (ba-tteries) or by unsuitable working conditions (e.g. high temperatures, high humidity, quakes,…).
Repair, modification or other failure action to the product by unauthorized person.
End-user did not prove enough his right to claim (time and place of purchase).
Data on presented documents differs from data on products.
Cases when the claiming product can not be indentified according to the presented documents (e.g. the serial number or the warranty seal has been damaged).

Authorized service centres

FAST OR, a. s.
Cernokostelecka 1621
CZ 251 01 Many
Ceska republika
Tel.: +420/ 323 204 120
Fax: +420/ 323 204 121
servis.praha@fastcr.cz
www.fastcr.cz

FAST OR, a. s.
Cejl 31 CZ 602 00
Brno Oeska republika
Tel.: +420/ 531 010 295
Fax: +420/ 531 010 296
servis.brno@fastcr.cz
www.fastcr.cz

Fast Plus, spol. s r. o.
Na Pantoch 18 SK 831 06
Bratislava Slovenska republika
Tel.: +421/ 249 105 811
Fax: +421/ 249 105 810
fastplus@fastplus.sk
www.fastplus.sk

Fast Hungary Kft.
Dulacska u. 1/a
H-2045 Torokbalint
Hungary
Tel.: + 36/ 23 330 830
Fax: + 36/ 23 330 8274
fasthungary@fasthungary.hu
www.fasthungary.hu

Uab „Senuku Prekybos
Centras” Garantinis Servisas
Jonavos G. 62, Lt-44192, Kaunas, Lithuania
Tel.: +370 37 212 146
Tex.: +370 37 212 165
garrem@senukai.lt
www.senukai.lt

Fast Poland, Sp. z o.o.
Sokolowska 10
PL 05-090 Puchaty
Poland
Tel.: +48 500 116 777
Fax: +48 22 869 96 13
fastpoland@fastpoland.pl
www.fastpoland.pl

Logo