Yuwei Technology P9 Dog Training Collar User Manual
- June 5, 2024
- Yuwei Technology
Table of Contents
- Yuwei Technology P9 Dog Training Collar
- Product Introduction
- Screen
- Package Content
- Product Specification
- How to Install the Contact Points and Conductive Silicone
- How to Operate the Transmitter and Receiver
- How to Adjust the Shock Level and Vibration Level
- How to Use the Collar Correctly
- How to Put the Collar on Your Dog
- How to Pair the Remote Transmitter with Receiver
- How to Use Test Light Tool
- How to Charge the Transmitter and Receiver
- warning
- FCC STATEMENT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Yuwei Technology P9 Dog Training Collar
Thanks for purchasing our products. For optimum performance and safety. please read this manual carefully before operating the Dog Training Collar and keep this manual for future reference.
Product Introduction
Screen
Package Content
Product Specification
Product Name | Dog Training Collar |
---|---|
Model | pg |
Charging Voltage
| Input Voltage, AC100-240V
Outpu t Voltage: OCSV l OOOmA
Battery| Li-Polymer Battery
Remote/Receiver Charging Time|
1-2 Hours
Remoting Distance
| Normal Environment: 1800ft Open Space: 3000ft
Function| Beep, Vibrate. Shock, Lighting
How to Install the Contact Points and Conductive Silicone
Caps
How to Operate the Transmitter and Receiver
- .Press any button to activate the Transmitter
- Press Cl button once. the green Ilg ht flashes once and the receiver beeps once. indicating the receiver
- Press button once to send a vibration. beep.shock command to Receiver Collar
- Press l)button once. the red Ilg ht flashes twice and the receiver beeps twice. Indicating the receiver is off.
How to Adjust the Shock Level and Vibration Level
- Press f button once until the shock symbol flashes, then press·+··-· button to adjust the shock level from 1-l 6.
- Press !II button once until the vibration symbol flashes. then press·+··-· button to adjust the vibration Level from 7-8
Note
- To avoid hurting your dog, please always start at the lowest level of Shock and Vibration. lhe appropriate level can be found when the dog reliably responds to the vibration/shock.
- Do not hold f / 1111 for a long time to avoid physical or psychological harm to the dog.
How to Use the Collar Correctly
- Unfasten the nylon belt and remove the slide buckle.
- Thread the nylon belt through the Receiver.
- Thread the nylon belt through the slide buckle.
- Thread the nylon belt through the side release buckle.
- Thread the excess nylon belt through the sllde buckle to make sure your collar
How to Put the Collar on Your Dog
- With your dog standing, center the contact points underneath your dog’s neck.
- .lfyour dog has thick fur. please use a comb to separate the fur at the electrodes to enable them to reach the skin
- The contact points must be in direct contact with the dog·s neck skin. The tightness is best if one finger can be inserted between the collar and neck
How to Pair the Remote Transmitter with Receiver
- Turn on the Receiver.
- Press and hold Cl button until the green light flashes and the receiver beeps three times.
- Press button on the transmitter. then pairing is completed.
- lf Dog B or Dog C Receiver does not respond. Pairing may be required
- AII” Modes, Press CH button four times. the symbols of DOG A DOG B. and DOG C will be displayed simultaneously. At this point, the transmitter can control all three dogs at once
NOTE:
There is only one Receiver COiiar in the package. If you would like to add
more Receiver COiiars to your training system, please purchase the same model.
How to Use Test Light Tool
- .Make sure the Transmitter and Receiver Collar are paired
- Put the test light tool vertically on the 2 contact points.
- Press f button on the Transmitter. then the test light will flash
- Turn the Receiver Collar off.
Keypad Lock Function
Press ‘9 button for 3s to turn on/off the keypad lock
function
How to Charge the Transmitter and Receiver
- Use the USB cable included to connect both the Transmitter and Receiver
- Plug the USB cable into an adapter {not included) or a power bank
- Fully charge the two units before first use
Note
- When the Transmitter is charging, the LED indicator will tum red. When fully charged, the LED Indicator wlll turn green and the screen wlll display four bars of power.
- When the Receiver is charging, the LED indicator wlll turn red. When fully charged, the LED indicator wlll turn green.
- When the battery ls less than 5%. the Indicator will turn red and blink.
To Maximize the Distance
The remote range depends on the way of the Transmitter being held. For best
results. keep the Transmitter in a vertical position <N1ay from your body and
above your head.
Note
Avoid touching the antenna, as the range may decrease substantially.
warning
- Do not use the product on dogs under 6 months of age.
- Do not use the product when your dog is in heat. pregnant or in poor health
- Do not allow children or anyone who has never trained a dog to use this product
- Do not disassemble the product at will
- lfyour dog reacts with fear during training. check if the shock/vibration level is too high for your dog.
- Use “shock” as little as possible and strengthen verbal commands when necessary. Don’t over-correct your dog’s behavior.
- Before using the product. your pet should be able to recognize basic obedience commands. such as “sit” or ·stay”.
- Do not operate the device at temperatures of 104″F and above. which may degrade battery performance
- Do not put the collar on your dog for more than 12 hours as it may cause a rash or irritate your dog’s skin.
- When you are not training the dog, please set the product to keypad-lock mode or remove the collar from the dog’s neck
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: This device may not cause harmful interference,
and this device must accept any interference received, including interference
that may cause undesired operation. Any Changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>