LEZYNE 73971-Y16 Super Bright STVZO Alert Rear Electric Bike User Manual
- June 5, 2024
- Lezyne
Table of Contents
LEZYNE 73971-Y16 Super Bright STVZO Alert Rear Electric Bike User Manual
READ ENTIRE MANUAL BEFORE OPERATION to ensure proper use and care of your new Lezyne LED light. Traffic laws mandating lighting vary from country to country. Inform yourself about lighting laws and regulations in the country of use.
Our e-bike lights are powered by the motor of an e-bike and need to be manually installed. Proper installation may require some disassembly of the bike and motor (depending on make and model/battery type) and additional wiring to connect the light to the motor. Please contact the e-bike or motor manufacturer for installation instructions. Please note: any disassembly may void the warranty of your e-bike. It is highly recommended to have a trained e-bike professional install your lights for you. Below is general information about electrical connectivity.
Technical Data
- Brightness: 35 Lumens
- Power, 6VDC input : 0.6 W
- Power, 6VDC input (Alert) : 1.8 W
- Ampere, 6-12VDC: 0.1A
- Ampere, 6-12VDC (Alert) : 0.3A
- Illuminant : 2 LEDs
- Illuminant (Alert) : 10 LEDs
- Power cable length : 135 cm
Motors Compatibility
- Bosch (6V) / Bosch (12V)
- Shimano E5000, E7000, E6100, E6110, E9000
- Shimano E6000, E6001, E6010, E6050
- Shimano E8000, E8080, E6002, E6012
- Yamaha PWse / Yamaha PW
- BionX
- Brose Drive T (2018) / Brose Drive S (2018)
- Continental 48V Prime / Continental 48V Revolution (12 Volt output)
Warnings
The light technical equipment must be safely installed during the entire usage and must be ensured that the light will not be moved in its position due to unintentional adjustment.
DO NOT LOOK DIRECTLY INTO LIGHT BEAM or shine into eyes of another.
DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.
Warranty
In U.S. and U.K., Lezyne LED Lights carry a two (2) year warranty from the original purchase date to the original owner (proof of purchase required). Lezyne warranties cover any manufacturing defects in materials or workmanship. Issues not covered by warranty include normal wear & tear, improper installation, attempting to access or modify electronics, damage or failure due to accident, misuse, abuse and/or neglect.
For all warranty issues worldwide, please contact the retailer that sold the product.
In the case of an LED not working properly or not working at all do not use your light anymore. These lights must be replaced immediately.
For any warranty questions contact: warranty@lezyne.com
Mounting
The light must be mounted in a height between 250 mm and 1200 mm. It must be ensured that the light technical equipment will not be covered by any parts of the bike (tire, etc…).
Installation
Lezyne recommends having an e-bike professional install our e-bike lights.
Below is general wiring and mounting information.
Use the hole pattern to drill/align the holes on the rack for mounting.
Operation
The light is controlled via the e-bike control panel and should only be powered by a 6V or 12V DC supply. The e-bike system must be capable of automatically shutting the light off when the onboard battery reaches a critical voltage to avoid over discharging the battery.
‘Alert ’ Function
Advanced “Alert” technology detects deceleration and automatically switches to full brightness when stopping to alert riders or vehicles behind. Once riding is resumed, the light will automatically return to its previous output mode.
Hole Pattern Guide
More Information
For more information on Lezyne products, visit: www.lezyne.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>