Dimplex EVN20SL Opti-myst Electric Stove Instruction Manual
- June 5, 2024
- Dimplex
Table of Contents
EVN20SL Opti-Myst Electric Stove
Instruction Manual
Dimplex Opti-Myst Electric Stove
Models: Bayport BYP20/Evandale EVN20
Evandale Slate EVN20SL
These instructions should be read carefully and retained for future use. Note
also the information presented on the appliance.
This product is only suitable for well-insulated rooms or for occasional use.
The product complies with the required Product Safety, Electromagnetic Compatibility, and Environmental Standards. This product is fully compliant with LVD, and EMC. RoHs and EcoDesign Directives.
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR
DAMAGE AND MAY INVALIDATE YOUR GUARANTEE
Important Safety Advice
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electrical shock and injury to persons, including
the following:
If the appliance is damaged, check with the supplier before installation and
operation.
Do not use outdoors.
Do not use it in the immediate surroundings of a bath, shower, or swimming
pool.
Do not locate the appliance immediately below a fixed socket outlet or
connection box.
Warning: This heater must not be used for anything other than normal
domestic household purposes in the country where it was purchased from a
recognized commercial retailer.
Do not use this heater if it has been dropped
Do not use if there are visible signs of damage to the heater.
Use this heater on a horizontal and stable surface, or fix it to the wall, as
applicable.
Children of less than 3 years should be kept away unless continuously
supervised. Children aged from 3 years and less than 8 years shall only switch
on/off the appliance provided that it has been placed or installed in its
intended normal operating position and they have been given supervision or
instruction concerning the use of the appliance in a safe way and
understanding the hazards involved.
Children aged from 3 years and less than 8 years shall not plug in, regulate
and clean the appliance or perform user maintenance.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Warning: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own unless constant supervision is provided.
Warning: This appliance must be earthed.
The use of an extension lead or multi-plug adaptor is not advised when
connecting this product to the mains. Connection through these devices could
lead to a risk of overloading, overheating, and even fire at the extension
lead or adaptor due to inadequate connection quality.
This heater must be used on an ~alternating current supply (~) only and the
voltage marked on the heater must correspond to the supply voltage.
Do not use this appliance in series with thermal control, a program
controller, a timer, or any other device that switches on the heat
automatically, since a fire risk exists when the appliance is accidentally
covered or displaced.
DO NOT use the heater on deep pile carpets or the long hair type of rugs, or
less than 750mm (30”) away from any overhanging surface. Keep combustible
materials such as drapes and other furnishings clear from the front, sides,
and rear of the heater. Do not use the heater to dry your laundry.
In the event of a fault unplug the appliance. Unplug the appliance when not
required for long periods.
The appliance must be positioned so that the plug is accessible. If the supply
cord is damaged it must be replaced by the manufacturer or service agent or a
similarly qualified person in order to avoid a hazard. Keep the supply cord
away from the front of the appliance.
Caution: Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present. This instruction can be found at
www.dimplex.co.uk
Warning: In order to avoid overheating, do not cover the appliance. Do
not place material or garments on the appliance, or obstruct the air
circulation around the appliance, for instance by curtains or furniture, as
this could cause overheating and a fire risk.
The appliance carries a DO NOT COVER warning
Warning: To reduce the risk of fire, keep textiles, curtains, or any
other flammable material a minimum distance of 1m from the air outlet.
Warning: In order to avoid a hazard due to inadvertent resetting of the
thermal cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
Dimplex Opti-Myst Stoves
Models: Bayport / Evandale / Evandale Slate / Evandale Pebble
Thank you for choosing a Dimplex electric fire
General Information
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the year.
A fan heater can provide heating in cold weather. A distance of 1 meter (3
feet) must be maintained between the front of the heater and any surrounding
furniture, overhanging curtains, or other obstructions.
Always ensure that the appliance is sitting on a level surface.
Before connecting the appliance, check that the supply voltage is the same as
that stated on the appliance.
Only use filtered water in this appliance.
Once installed, never move this appliance or lay it on its back, without
draining the water from the sump and water tank. The water tank, sump, sump
lid, tank cap, and air filters must be cleaned once every 1 Week, particularly
in hard water areas. If you intend not to use the appliance for longer than 1
Week, drain the water from the sump and water tank and dry the sump.
Please note: Used in an environment where background noise is very low, it may
be possible to hear a sound that is related to the operation of the flame
effect. This is normal and should not be a cause for concern.
The sump and the water tank in this product are treated with a biocidal
product, Silver Biocide in order to control harmful or unwanted organisms.
This conforms with the latest relevant ISO standard Do not drink the water
from the sump or from the water tank(s)
Technical Information
Model No: BYP20, EVN20, EVN20SL, EVN20PB
Heat Output| | 230V| 240V|
---|---|---|---|---
Nominal Heat Output| PNom| 1.6| 1.8| kW
Minimum Heat Output| Pmin| 0.8| 0.9| kW
Maximum Continuous Heat Output| Pmax| 1.6| 1.8| kW
Auxiliary Electricity Consumption
In Standby Mode| PNom| 0.58| 0.6| W
with electronic room temperature control.
Installation Instructions
This heater must be used on an AC ~ supply only and the voltage marked on the
heater must correspond to the supply voltage. Before switching on, please read
the safety warnings and operating instructions. Please retain this user’s
guide for future reference
Ensure that all packing items are removed (read any warning labels carefully).
Retain all packing for possible future use e.g. in the event of moving or
returning the appliance to your supplier.
Installing the Appliance;
- Clean the area where the fire will be installed e.g remove ash residue from an existing fireplace.
- Hold the fire by the sides of the surround and gently maneuver it into position.
- Plug the fire into a 13amp/240-volt outlet. Ensure that the supply cable is not trapped under the fire such that it might cause it to be damaged.
Connecting the Transducer
- Open the stove door
- Gently lift out the fuel and carefully set it aside. (Fig 4)
- Remove the water tank by lifting upwards and outwards. (Fig 5)
- Remove the nozzle by unclipping and lifting upwards and outwards. (Fig 6)
- The transducer will be inside the sump. Remove from its bag.
- Place the Transducer unit into the sump and make the connection.
- Locate the tab on the Transducer unit into the molded recess in the base of the sump (Fig 7A)
- Ensure that the cable does not obstruct the Transducer disc. To prevent the cable from becoming pinched between the nozzle and the sump, place the cable in the slot in the wall of the sump. (Fig 7B)
Filling the Water Tank
- Gently lift out the fuel and carefully set it aside.
- Remove the water tank by lifting upwards and outwards.
- Place the water tank in the sink and remove the cap, Anti-clockwise to open. (Fig 8)
- Fill the tank with filtered tap water only. This is necessary to prolong the life of the flame and smoke-producing unit. The water should be filtered through a conventional domestic water filter unit and the filter should be replaced regularly.
- Screw the cap back on, do not over-tighten.
- Return the tank to the sump, with the tank cap facing down
- Gently place the fuel bed back into position.
When the water tank is empty, the flame and smoke effect shuts off, you will hear 2 audible beeps and the digital display will display
Operating The Product
WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN
INJURY AND/OR DAMAGE.
Manual Controls
The manual controls are located behind the stove door. Open the stove door to
access the manual controls. (Fig 2) is the on/standby button. Press it once to
turn on the product. Press it again to turn off the product. When turned on a
‘beep’ will sound and the digital display will show followed by the current
room temperature. The display will then turn off. The fuelbed will light up.
Be careful not to look directly into the fuel as the LED lights are very
bright. It will take approximately 45 seconds before the flame effect starts.
is the Mode button.
Press it once and you will be in the HEAL options. The display will show
the current setting. Using the and buttons you can turn the heat on at the LOW
or HIGH setting and turn the heat OFF.
You will hear two ‘beeps’ for the LOW heat setting, three ‘beeps’ for the HIGH
heat setting, and one ‘beep’ when the heat is turned off.
Press it a second time and you will be in the temperature set mode . The display will show the current room temperature and then the set point temperature. Using the buttons you can adjust the set point temperature up and down. Note: if the set point temperature is below the room temperature the heat function will not operate. The temperature range is from 15-35°C
Press it a third time and you will be in the Fire mode. The display will show followed by the current fire effect setting. There are six fire settings. Using the and buttons you can adjust the height of the flame effect.
Press M| Display| Function| Press + or –|
---|---|---|---|---
Once| | Controls the fan heater| Off
Low| High
Twice| | Thermostat| From 15 °C| To 35 °C
Three times| | Flame intensity| From F1 (low)| To F6 (high)
Remote control
The remote control is supplied with a battery already in place. Simply pull on
the clear plastic tab on the back of the remote control to enable the battery.
-
is the on/standby button. Press it once to turn on the product. Press it again to turn off the product. When turned on you will hear on ‘beep’ and the digital display will show followed by displaying the current room temperature. The display will then turn off. The main LED lights will activate. Be careful not to look directly into the LEDs. These are very bright. Although the main lights operate immediately it will take a further 45 seconds before the flame effect starts.
-
Press once to activate the heat setting. Press it again to activate the heat setting.
If you continue to press this button you will cycle through the LOW and HIGH heat settings. You will heat two ‘beeps’ for the LOW heat setting and three ‘beeps’ for the HIGH heat setting -
Press once to turn off the heat. You will hear one ‘beep’
-
Press the button to display the current room temperature followed by the current set point temperature
-
Press the buttons to adjust your set point temperature. Note: if the set point temperature is below the room temperature, the heat function will not operate. The temperature range is from 15 – 35°C
-
Press to increase the setting.
-
Press to decrease the setting.
Setting the Thermostat
Plug in the product and press to turn it on. Press the button twice to enter
the temperature set mode . The current room temperature will be displayed
(e.g. r23C) followed by the current set point room temperature (e.g. 26C).
Press the buttons to select your set point room temperature. Allow the display
to turn off. Press the button once to enter the Heat option. Press the and
buttons to select either or heat output. The heater will turn on when your
set point room temperature is higher than the room temperature.
Thermal Safety Cut-out
A thermal safety cut-out is incorporated into the fan heater to prevent damage
due to overheating. This can happen if the heat outlet was restricted in any
way. If the cut-out operates, unplug the heater from the socket outlet and
allow approximately 10 minutes before reconnecting. Before switching the
heater back on remove any obstruction that may be restricting the heat outlet,
then continue normal operation.
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a switch that is regularly switched on and off by the utility.
Getting the Desired Flame Effect
- Using the manual controls or the remote control choose a setting between F1 and F6. F1 is the lowest setting and F6 is the highest setting.
- Generally, the flames appear more realistic when the flame control is turned down.
- Give the flame generator time to react to changes you may make.
- The fire will use less water if the flame effect is set to a lower level.
- Do not tilt or move the fire while there is water in the tank or sump.
- Make sure that the fire is on a level floor.
Maintenance
General Tips
Only use filtered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not to use the appliance for longer than 1 Week, remove and
empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining
the water from the sump and water tank.
Cleaning
Warning – Always press to turn off the product and disconnect the product
from the power supply before cleaning the fire. Leave the appliance for 10
minutes to allow the product to cool down.
We recommend cleaning the following components once every 1 Week,
particularly in hard water areas:
Water Tank, Sump, Nozzle, Tank cap and seal, Air filter.
For general cleaning use a soft clean duster – never use abrasive cleaners.
To remove any accumulation of dust or fluff, the soft brush attachment of a
vacuum cleaner should occasionally be used to clean the outlet grille of the
fan heater.
Water Tank
- Remove the water tank, as described earlier, put into the sink and empty water.
- Using the supplied brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in the outer groove and the center rubber seal.
- Put a small quantity of washing-up liquid into the tank, refit the cap and shake well, rinse out until all traces of washing-up liquid are gone.
- Refill with filtered tap water only, replace the cap, and do not over-tighten.
Sump
Press to put the product into standby
Gently lift out the fuelbed and place it carefully on the ground.
Remove the water tank by lifting upwards.
Remove the sump lid, this allows the sump to be lifted completely from its
location. (Fig 5)
Gently lift up the sump, taking care to keep level so as not to spill any
water. Set the assembly in the sink.
Carefully tilt so that the liquid drains out of the sump.
Put a small amount of washing-up liquid into the sump, and using the supplied
brush, gently clean all surfaces including the metal disc (Fig 9)
When cleaned, thoroughly rinse the sump with clean water.
Clean the outlet surface of the sump lid with the brush and flush it out
thoroughly with water.
Reverse the above steps to reassemble.
Air Filter
- Press on the remote control or on the product to turn it off
- Gently lift off the fuelbed and set aside
- Remove the tank and place it in a sink with the cap facing upwards.
- Gently slide up the air filter (Fig. 10)
- Gently rinse with water in the sink and dry with a fabric towel before returning.
- Replace the filter making sure that the course black filter is in contact with the plastic holder.
- Replace the tank.
- Replace the fuelbed.
- Press to turn on the product
General Cleaning and Maintenance
The outside can be cleaned by wiping it over with a soft damp cloth and then
dried. Do not use abrasive cleaning powders or furniture polish, as this can
damage the surface
finish.
CAUTION: Assembly, installation, and repair of this heater must be
carried out by Dimplex or its authorized agent.
CAUTION: We recommend that you arrange for this heater to be checked
annually for safety by a qualified electrician.
Additional Information
After Sales Service
Your product is guaranteed for one year from the date of purchase. Within this
period, we undertake to repair or exchange this product free of charge
(excluding transducer discs & subject to availability) provided it has been
installed and operated in accordance with these instructions. Your rights
under this guarantee are additional to your statutory rights, which in turn
are not affected by this guarantee.
The transducer is a consumable item and may need to be replaced over time,
depending on its usage. Replacement transducers can be purchased from our
website http://spares.dimplex.co.uk.
The transducer has a 12-month warranty period.
CAUTION: Do not use if the heater’s main power lead is damaged. Such use
may cause a hazard.
If damaged, the main power lead must be replaced by the manufacturer or its
authorized dealer.
Should you require after-sales information or assistance with this product
please go to www.dimplex.co.uk and select
“Customer Support” or ring our help desk on 0344 879 3588 (UK) or 01 842 4833
(R. O. I.). Spare parts are also available on the website.
Please retain your receipt as proof of purchase.
Recycling
At the end of the electrical product’s useful life it not be disposed of with
household waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice in your country.
Patent/Patent Application
Products within the Optimyst range are protected by one or more of the
following patents and patent applications:
Great Britain GB2460259B, GB2475794B, GB2418014, EP2029941, GB2436212,
GB2402206B
United States US8413358, US8136276, US7967690, US8574086
Russia RU2434181
European EP2029941, EP2315976, EP1787063 (A1), EP2388527
China CN101883953A, CN102105746A, CN101057105 (A), CN101438104
Australia AU2009248743A1, AU2007224634
Canada CA2725214, CA2579444, CA2645939
South Africa ZA2008/08702
Mexico MX2008011712
South Korea KR101364191
Japan JP5281417, JP5496291
Brazil BRP10708894
India 4122/KOLNP/2008
New Zealand NZ571900
| 
---|---
Tel: 0344 879 3588
Republic of Ireland Tel: 01 8428 222
www.dimplex.co.uk
© Glen Dimplex Heating & Ventilation..
Millbrook House, Grange Drive, Hedge End, Southampton, SO30 2DF
© Glen Dimplex Heating and Ventilation. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex Heating and Ventilation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>