CHASING Grabber Arm 2 for M2-M2 Pro-M2 Pro Max User Manual
- June 12, 2024
- CHASING
Table of Contents
Grabber Arm 2 for M2-M2 Pro-M2 Pro Max
User Manual
CHASING Grabber Arm 2
User Manual
V1.0
Grabber Arm 2 for M2-M2 Pro-M2 Pro Max
CHASING Grabber Arm 2 is a customized accessory for the Gladius series. Its
simple and easy tool replacement form and intelligent grip control system
provide more help for users to explore unknown underwater areas.
- Two-jaw clamp
- Mounting port of the claw
- Thumb screw
- Grabber Arm 2
- Port of the 4-pin connection cable
- Mount holder of the Grabber Arm 2
Installation and Use Instructions
- Install the grabber claw on the ROV support rod and fix it with four M3*8 screws. Plug one end of the 4-pin double-headed connection cable into the 4-pin port at the rear of the grabber claw, and tighten it with hand. Then, plug the other end of the connection cable into the 4-pin port on the side of the ROV (depth sensor), and tighten it with hand.
- Wait for the ROV to activate after turning on before operating: Press and hold the grabber claw button on the remote controller or enable the grabber claw function in app settings, and then use the right thumb wheel on the remote controller to control the opening and closing of the grabber claw.
Tool Head Replacement
- ① Turn the right wave wheel on the right to open the original tool head to the maximum,② Remove the thumb screw, ③ Remove the claw before you replace it.
*Note: When there is no
tool head installed on the grabber claw, if you need to install a tool head,
turn the right wave wheel to extend the middle shaft to the front end, then
install the tool head.
Specifications
| Maximum Opening Of The Grabber Claw | 170 mm |
|---|---|
| Maximum Gripping Force | 7 kg |
| Main Body Weight | 446 g |
| Two-jaw Clamp Weight | 76 g |
| Maximum Diving Depth Supported | 100 m |
| Dimensions Of Grabber Claw Body | 380 × 35 × 35 mm |
| Two-jaw Clamp Size | 125 × 53 × 22 mm |
Notes
- Before using the remote controller to control the grabber claw, press and hold the button on the rear-right (with the grabber claw icon) or enable the grabber claw function in app settings.
- When installing the tool head of grabber claw, you need to extend the middle shaft to the front end by using the remote controller before installing the claw. Make sure the ROV is powered off before you install and connect tithe grabber claw.
- Check the ROV and make sure the ports are dry and clean before use. Salt and moisture may corrode the port. If there are water droplets in the port, be sure to flush the port with fresh water, and then use a paper towel or cotton ball to absorb the water in the port.
Support
If you have any questions or technical issues, send an email to the aftersales
services of Chasing or contact us on the official website.
Aftersales support on the official website: https://www.chasing.com/ >>
Contact us >>
Online Customer Support >>Click here
Aftersales service email addresses: support01@chasing-
innovation.com for Europe,
support02@chasing-innovation.com
for Asia and Oceania, and support03@chasing-innovation.com for South America,
North America, and Africa.
This guide may be updated without notice.
Visit the Chasing official website for the latest version:
https://www.chasing.com
www.chasing.com
support@chasing-innovation.com
References
- Innovation | Domain Name Coaching
- vation.com
- CHASING | The World's Most Innovative Underwater Drones
- CHASING | The World's Most Innovative Underwater Drones
- CHASING | The World's Most Innovative Underwater Drones
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>