wiltec 51703 Lawn Sweeper Instruction Manual

51703 Lawn Sweeper Instruction Manual51703 Lawn Sweeper
Instruction Manual

51703 Lawn Sweeper

Illustration similarities may vary depending on the model:
Read and follow the operating instructions and safety information before using it for the first time. Technical changes reserved! Due to further developments, illustrations,  functioning steps, and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us.
The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown. Even though WilTec Wildanger Technik GmbH has undergone the biggest possible efforts to ensure that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided. If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing from you.
Send an e-mail to:service@wiltec.info
or use our contact form: https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop at: https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick the goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously to place your order via the webshop.
E-mail: service@wiltec.info
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15
To return orders for exchange, repair or for other purposes, please use the following address. Attention!
To allow for the smooth execution of your complaint or return, it is important to contact our customer service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: service@wiltec.info
Tel:+49 2403 55592-0
Fax: +49 2403 55592-15

Introduction

Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instructions carefully and make sure you have understood its content. Keep these operation instructions safe.
Safety instructions
Remember that any power equipment can cause injury if operated improperly, or if the user does not understand how to operate the equipment. Exercise caution at all times hen using power equipment.

• Read the vehicle and sweeper owner manual and know how to operate your vehicle and sweeper before using the sweeper attachment. Always instruct other users before they operate the sweeper.
• Do not permit children to operate the sweeper.
• Do not permit anyone to ride on the sweeper.
• Never attach the hopper rope to any part of your body or clothing! Never hold onto the rope while towing the sweeper! Attached the rope to the towing vehicle to keep it away from wheels and rotating parts.
• Operate the sweeper at reduced speed on rough terrain, near ditches and on hillsides to prevent loss of control.
• Speed limit: maximum speed is 9 km ⁄h (6 mph).
• This sweeper is not designed for street or highway use. Watch for traffic when sweeping near roadways.
• This product may be used for lawn sweeping and may collect leaves, branches and etc.; it is not designed for heavy and sharp garbage like stones or steel objects.
• Do not exceed the maximum capacity of the hopper.
• Vehicle braking and stability may be affected by the attachment of this sweeper. Do not fill the sweeper to its maximum capacity without checking the capability of the towing vehicle to safely pull and stop with the sweeper attached. Stay off of steep slopes.
• Stop and inspect the vehicle and the sweeper for damage after striking an object. Repair any damage before continuing the operation.
• Keep the sweeper away from fire. The hopper bag and its content could burn.
• Before storing the sweeper, always empty the hopper bag to avoid spontaneous combustion.
• Make sure the sweeper will not be used in the conditions of bad weather such as strong wind, high air pressure, etc.
• Please replace the hopper when it is worn out; keeping using a damaged hopper may be dangerous.
• Axle lubrication needs to be added before each usage.

Scope of delivery (loose parts)

Main components

Screwing material

Assembly

REMOVE THE HARDWARE PACK AND ALL LOOSE PARTS FROM THE BOX AND VERIFY THAT ALL THE PARTS AND FASTENERS SHOWN ON THE  LAST PAGE ARE INCLUDED.
Sweeper assembly
Note: Right hand (R. H.) and left hand (L. H.) are determined from the operator’s position on the tractor.
fig. 1: Connect the angle bracket to the sweeper housing using an M8×16 hex bolt and an M8 hex lock nut. Make sure that the bracket is turned as shown and aligned straight with the housing, then tighten.

fig 2: Assemble the R. H. hitch tube to the sweeper housing using an M6×40 hex bolt and an M6 lock nut. Do not tighten yet.  Repeat for the L. H. hitch tube.

fig. 3: Fasten the hitch tubes together using two M8×65 hex bolts and M8 lock nuts. Do not tighten yet.

The tractor hitch ground clearance determines how to proceed:
clearance from 279 to 330 mm > 4
clearance from 203 to 279 mm > fig. 5
fig. 4 u. 5: Assemble the hitch brackets to the hitch tubes using two M8×50 hex bolts and M8 hex
lock nuts. The bolts should straddle the front hitch tube bolt. Do not tighten yet.
Now tighten the four bolts fastening the hitch tubes to the sweeper housing. Next, tighten the two bolts fastening the ends of the hitch tubes together. Finally, tighten the two bolts fastening the hitch brackets to the hitch tubes.
Assemble the hitch pin, the spacers, and the hair cotter pin to the hitch brackets.

fig. 6: Assemble the height adjustment handle to the height adjustment tube as shown in fig. Use two M8×40 hex bolts and M8 lock nuts. Do not tighten yet.

fig. 7: Insert an M8×20 hex bolt through the angle bracket. Assemble onto the bolt (in order) the spacer bushing, the height adjustment strap, an ⌀8 big flat washer, and an M8 hex lock untighten.

fig. 8: Position the height adjustment handle side to side so that the external teeth washer can fit between the handle and the height adjustment strap. Tighten the nuts securing the height adjustment handle.

fig. 9: Assemble the connecting rod to the sweeper housing by using two sets of M6×12 hex bolt and M6 lock nut.

Hopper Bag Assembly

fig. 10: Turn a rear hopper tube so that the brace holes in the middle of the tube face down. Slide the tube through the two loops sewn to the top rear seam inside the hopper ag.

fig. 11: Insert the two upper hopper side tubes through the flaps stitched on each side of the hopper bag.
Assemble the ends of the rear hopper tube onto the ends of the upper hopper side tubes.

fig. 12: Turn the second rear hopper tube so that the brace holes in the middle of the tube face up. Assemble the ends of the rear hopper tube onto the ends of the lower hopper ide tubes. Fasten them together using plastic plugs.

fig. 13: Place the assembled low hopper tubes into the bottom of the hopper bag. Attach the ends of the lower hopper side tubes to the inside of the upper side tubes using two ⌀9.5×25 clevis pins inserted from the inside, and two hair cotter pins ⌀3

fig. 14: Insert the bag frame strap into the stitched sleeving the front edge of the bag bottom. Assemble the bag frame strap to the lower hopper side tubing two ⌀6×37 clevis pins and two ⌀2 hair cotter pins.

fig. 15: Secure the bag corners around the lower hopper side tubes by snapping the bag flaps to the bag bottom on both sides.

Important: Do not over-bend the support rods during the following step. Overbending will cause the steel rods to lose their supporting tension. 10.
fig. 16: Tip the hopper onto its back to assemble the two hopper support rods (1). Place the ends of each rod into the upper and lower rear hopper tubes bending the rod just enough to fit it into the holes in the tubes.

fig. 17: Feel along the stitched flap on the hopper bag to locate the lower hole in each upper hopper side tube. Place a hole through both sides of the stitched flaps in alignment with the lower hole.
fig. 18: Insert an ⌀8×59.5 clevis pin through the lower hole in each upper hopper side tube. Next, assemble a bag arm tube onto each clevis pin and secure it with a ⌀3-hair cotter pin.
fig. 19: Secure the rope to the top center of the hopper bag frame.

fig. 20: To assemble the hopper bag to the sweeper, slide the ends of the bag arm tubes into the ends of the sweeper hitch tubes and secure them with two ⌀6×37 clevis pins and  2 hair cotter pins.

Technical specifications

Explosion view and parts list

Important notice: The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction manual require the written permission of WilTec Wildanger Technik GmbH.

© by WilTec Wildanger Technik GmbH
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

References

• Aoyue.de
• Teichtip.de
• WilTec - Ihr Online Shop für Haus, Garten, Werkstatt, Freizeit
• Unternehmen: WilTec Wildanger Technik GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>