concept KS 3006 2000W Convector Floor Standing Heater Instruction Manual

: June 5, 2024
: concept

Convector

concept KS 3006 2000W Convector Floor Standing Heater

KS 3006

ACKNOWLEDGEMENT

Thank you for purchasing a Concept product. We hope you will be satisfied with our product throughout its service life.

Please study the entire Operating Manual carefully before you start using the product. Keep the manual in a safe place for future reference. Make sure other people using the product are familiar with these instructions.

Technical parameters

Voltage| 220 – 240 V ~ 50 Hz
Power input| 1800 – 2000 W
Noise level| 55 dB(A)

IMPORTANT SAFETY PRECAUTIONS:

Make sure that the connected voltage corresponds with the information on the product’s label. Do not connect the appliance to adapter plugs or extension cables.
Do not use this unit with any programmable device, timer, or any other product that turns the unit on automatically; covering the unit up or improper installation may result in a fire.
Place the appliance on a stable, heat-resistant surface, away from other heat sources.
Do not leave the appliance unattended if it is turned on or, in some cases, if it is plugged into the mains socket.
When plugging and unplugging the unit, the mode selector must be in the 0 (off) position.
Never pull the supply cable when disconnecting the appliance from the socket outlet, always pull the plug.
The appliance must not be placed directly below an electric socket outlet.
The appliance must always be placed in a way which makes the mains outlet freely accessible.
Keep the minimum safe distance of at least 100 cm between the unit and flammable materials, such as furniture, curtains, drapery, blankets, paper or clothing.
Keep the air inlet and outlet grilles unobstructed (at least 100 cm before and 50 cm behind the unit). WARNING! The outlet grille can reach a temperature of 80°C and higher when the appliance is in use. Do not touch it; there is a danger of scorching.
Never transport the unit during operation or when it is hot.
Do not touch the hot surface. Use the handles and buttons.
Do not allow children or irresponsible persons to operate the appliance. Use the appliance out of the reach of these persons.
Persons with limited movement capacity, reduced sensory perception, insufficient mental capacity or those who are unaware of the proper handling should use the product only under the supervision of a responsible person acquainted with these instructions.
Be especially careful when there are children near the appliance.
Do not allow the appliance to be used as a toy.
Do not cover the appliance. There is a risk of overheating. Do not use the appliance for drying clothes.
Do not hang anything above or in front of the unit.
Do not use this appliance in a way different from this manual.
The appliance can only be used in an upright position.
Do not use the unit near a shower, bathtub, sink, or a swimming pool.
Do not use the appliance in an environment with explosive gases or flammable substances (solvents, varnishes, adhesives, etc.).
Turn off the appliance, disconnect it from the electric socket outlet and let it cool down before cleaning and after use.
Keep the appliance clean; prevent foreign matter from entering the grille openings. It might damage the appliance, cause a short circuit, or a fire.
Do not use abrasive or chemically aggressive substances to clean the appliance.
Do not use the appliance if the power supply cable or the mains socket plug is damaged; have the defect repaired immediately by an authorised service centre.
Do not use the unit if it does not operate properly, if it has been dropped, damaged or submerged into liquid. Have the appliance tested and repaired by an authorised service centre.
Do not use the appliance outdoors.
The appliance is intended for household use only, not for commercial use.
Do not touch the appliance with wet hands.
Do not submerge the supply cable, mains socket plug or the appliance in water or other liquids.
Use only the supplied mounting kit when installing the appliance on a wall.
The unit must not be used in any means of transport.
Never repair the appliance yourself. Contact an authorised service centre.

Failure to follow the manufacturer`s instructions may cause refusal of warranty repair.

PRODUCT DESCRIPTION

concept KS 3006 2000W Convector Floor Standing Heater
1

Air outlet grille
Carrying handle
Thermostat regulator
Mode selector
Ventilator switch
Air inlet grille
Legs (according to assembly type)

Accessories

A Mounting kit for installation on a wall

ASSEMBLY

The unit must not be used without properly installed legs or proper installation on the wall.

a) Usage as a free-standing appliance
Before you start using the unit, attach the legs which increase its stability and enable the air to flow into the inlet grille.

Place the unit on a stable surface (e.g. table).
Attach the legs on the body.
Screw the legs firmly into the body (Fig. 1).

concept KS 3006 2000W Convector Floor Standing Heater fig
1

Fig. 1

b) Usage when mounted on a wall
Before its first use, the appliance must be properly mounted on a wall in a way which ensures a sufficient airflow into the inlet grille.

WARNING!
The appliance can only be installed on a wall made of inflammable material. No objects made of flammable material may be placed above the appliance. The lateral and frontal distance from surrounding flammable materials must be at least one meter. For detailed information and the minimum safe distance refer to Fig. 2.

concept KS 3006 2000W Convector Floor Standing Heater fig
2 Fig. 2

Assembly:

1. Draw two parallel lines 335 mm apart on the wall according to Fig. 3.
2. Mark and drill two holes corresponding with the diameter of the supplied dowels on the top line. The distance between their centres is 400 mm.
3. Mark two holes with their centres 396 mm apart on the bottom line so that they are symmetrical with the top holes. Drill the bottom holes with a drill of appropriate diameter according to the supplied dowels.

Fig. 3

4. Insert the supplied dowels in the four holes.
5. Put the supplied screws in the top holes. Allow an approximate 8 mm clearance between the screw head and the wall (Fig. 4).
6. Put suspension hooks on the screw heads and firmly tighten the screws (Fig. 5).

Fig. 4 Fig. 5

7. Screw the spacers to the bottom section of the appliance (Fig. 6). Make sure the spacers are located on the same side as the cut-outs for suspending the appliance.

Fig. 6

8. Hang the appliance on the suspension hooks installed on the wall and screw the spacers into the bottom holes (Fig. 7).

Fig. 7

9. Make sure the appliance is firmly installed on the wall and there is no danger of its fall during operation.

CAUTION
When turning the appliance on for the first time or after a prolonged downtime, it may produce a slight smell. This smell will vanish after a short time.

OPERATING INSTRUCTIONS

If you use the appliance as a free-standing unit, place it on a stable surface or floor to prevent it from overturning. If the appliance is mounted on a wall, make sure that all flammable substances in its vicinity conform to the minimum distance requirements.
Uncoil the supply cable completely.
Connect the power cord plug to the mains socket outlet.
Use the mode selector (4) to choose the power output 750, 1250 or 2000 W.
Use the thermostat regulator (3) to adjust the required room temperature. When 750, 1250 or 2000 W power outputs are selected, the unit will alternately switch on and off, thus keeping the required temperature. You can activate a fan with a switch (5) to rapidly reach the required room temperature.
Note: You can set a more accurate temperature in the following way: Set the thermostat to a maximum value, then switch the unit to the heating mode (750, 1250 or 2000 W). When the required room temperature is reached, turn the thermostat (3) slowly to a lower temperature until the unit switches off.
After use, switch off the unit and unplug it from the mains outlet.

CLEANING AND MAINTENANCE

Warning!
Always disconnect the power supply cable from the mains outlet before cleaning the appliance.
Make sure the appliance has cooled down before handling it.
Only use a wet cloth for cleaning the surface; never use detergents or hard objects, as they may damage it.
Clean and inspect the inlet and outlet grilles frequently to ensure the proper operation of the unit and prevent overheating.
Dust accumulated in the unit can be blown out or removed by a vacuum cleaner.
Never clean the unit under running water, do not rinse it or submerge in water.

REPAIR & MAINTENANCE

Any extensive maintenance or repair that requires access to the inner parts of the product must be performed by an expert service center.

ENVIRONMENTAL PROTECTION

Packaging materials and obsolete appliances should be recycled.
The transport box may be disposed of as sorted waste.
Polyethylene bags shall be handed over for recycling.

Appliance recycling at the end of its service life:
A symbol on the product or its packaging indicates that this product should not go into household waste. It must be taken to the collection point of an electric and electronic equipment recycling facility. By making sure this product is disposed of properly, you will help prevent the negative effects on the environment and human health that would otherwise result from inappropriate disposal of this product. You can learn more about recycling this product from your local authorities, a household waste disposal service or in the shop where you bought this product.

WARRANTY TERMS

Warranty

The manufacturer (or importer) is responsible for ensuring the product complies with the requirements of applicable legal regulations as well as those of the relevant technical standards. Moreover, they are responsible for ensuring the product has the properties the manufacturer described in documents related to the goods or those reasonably expected by the customer with regard to the nature of the goods or based on advertising produced by the manufacturer, and further they are responsible for ensuring the product is fit for the purpose proposed by the manufacturer or that a product of the same type is normally used for.

The quality warranty term is 24 months from product takeover by the customer.

The warranty does not apply to wear and tear caused by regular use. The customer shall not be entitled to any warranty claims if, prior to taking the product over, they knew the product contained a defect or if the defect is attributable to the customer.

The warranty specifically does not apply:

if the product installation, operation and service conditions stipulated in the product operating manual have not been adhered to,
to malfunctions caused due to mechanical, heat or chemical damage, short circuit, over voltage or incorrect installation,
to malfunctions caused by an inexpert third-party intervention,
to malfunctions caused by natural disaster,
to malfunctions caused by insufficient or inappropriate maintenance in violation of the operating manual, including malfunctions caused by water and other sediments,
to changes in colour of the heating surface or to scratching of the surface caused as a result of using the products in an unusual manner,
to appearance and functional changes caused by exposure to sunlight, thermal radiation of water and other sediments,
if the service life of certain product parts expires, e.g. for accumulators, bulbs, etc.

The warranty does not apply to any products and services provided along with the product (gifts, promotional articles, etc.).

Filing a complaint

A complaint against a product defect must be filed as soon as identified, yet no later than before the end of the warranty term.

The customer must file a product complaint with the dealer from which they have purchased the product, or with any authorised service centre, a list of which is included in the product package, or available at www.my- concept.com.

While filing a product complaint, the product must be duly cleaned and securely packed so as to prevent any damage during its transport to an authorised service centre, where relevant, unless the product is delivered in person.

The customer must submit proof of having concluded a purchase contract for the product by producing the receipt.

While filing their complaint, the customer must indicate the noted defect and identify the preferred complaint application method.

Complaints processing

As long as the noted defect may be removed, the user has the right to have the defect duly removed free of charge on a timely basis.

Where such a procedure is not reasonable with regard to the nature of the defect, the user may require to be supplied a new defect-free product (replacement), or, where the defect applies to a part of the product only, replacement of the part concerned. However, if replacement of the product or any part thereof is not proportionate with regard to the nature of the defect, especially if the defect can be removed without undue delay, the customer has the right to have the defect removed free of charge.

If the noted defect is not removable, or if the customer becomes entitled to replacement of the product or a part thereof, yet the replacement is not possible, for example due to the product having been sold out, the customer has the right to return the product (withdrawal from the contract).

The customer shall have the right to a new product (replacement) or to replacement of a part of the product even if the defect can be removed, provided they cannot properly use the product due to repeated occurrence of the defect or due to a high number of such defects. In such a case, the customer also has the right to return the product (by withdrawing from the contract).

If the product is not returned (the customer does not withdraw from the contract), or if the customer does not apply the right to a new defect-free product (replacement), to replacement of a part thereof or to repair of the product, they may request a reasonable discount. The customer also has a right to a reasonable discount if a new defect-free product cannot be supplied to them, or if a product part cannot be replaced or the product repaired unless the situation is remedied within a reasonable time limit, or if remedying the situation would create major discomfort on the part of the customer.

The seller, authorised service centre or a staff member authorised by them must decide about each complaint immediately or within three business days in complicated cases. This term does not include a reasonable period of time, depending on the type of product concerned, required for the defect to be assessed by an expert. A complaint, including defect removal, must be dealt with without any undue delay, yet no later than within 30 calendar days of the complaint filing date, unless the seller and the customer agree on a later deadline.

On returning the product (withdrawing from the contract) the customer must return any accessories and documents supplied along with the product.

The customer does not have the right to keep the defective parts and components of the product replaced as part of a repair of the product.

This shall be without prejudice to any other rights the customer may have in relation to the purchase of the product.

Remark: Complaints against products damaged in transport are governed by the carrier’s complaints procedure.

Manufacturer

Jindich Valenta – ELKO Valenta
Vysokomýtská 1800, 565 01 Choce
Czech Republic
tel.: +420 465 471 433
fax +420 465 473 304
Company ID No. 13216660
email: servis@my-concept.cz
www: www.my-concept.com