Lumenier QAV-PRO Mega Whoop Cinequads Edition Frame User Manual

QAV-PRO Mega Whoop Cinequads Edition Frame

Product Information:

Assembly Steps:

1. Guards Pre-assembly
2. Bottom Plate Pre-assembly
3. Top Plate Pre-assembly
4. Core Assembly
5. Guards Assembly
6. Final Assembly

Parts Needed for Assembly:

• X2 Guards Pre-assembly
  • X2 Bottom Guard
  • X2 Mid Guard
  • X34 M3x6mm Screws
  • X6 M3x14mm Screws
  • X18 M3x15 Standoff
  • X4 M3x29mm Standoff
  • X6 Carbon Fiber Tube
  • X6 Nylon Insert Landing Gear
• X1 Bottom Plate Pre-assembly
  • X2 Bottom Plate
  • X2 Rear Bracket
  • X1 Bone
  • X2 Isolation Camera Mount
  • X4 Battery Foam Pad
  • X4 DJI O3 Air Unit Heat Sink Set
  • X10 M3x6mm Screws
  • X2 M2x5mm Screws
  • X4 M2x8mm Screws
  • X2 M3x16mm Screws
  • X4 M2 Rubber Grommet
  • X2 M3 Hex Nut
• X1 Top Plate Pre-assembly
  • X2 Top Plate
  • X1 XT-90 Mount
  • X1 XT-90 Panel Mount
  • X1 Cable Bracket
  • X2 XT-30 Mount Set
  • X4 Crossfire Horizontal Mount
  • X4 Crossfire Vertical Mount
  • X16 Universal Washer
  • X6 M3x6mm Screws
  • X2 M3x8mm Screws
  • X2 M3x10mm Screws
  • X7 M3x16mm Screws
  • X7 M3x25mm Screws
  • X4 M2x6mm Screws
  • X1 ESC XT-90 Wiring
  • X7 18AWG Power Wire
  • X16 Motor Washer Plate
  • X4 SMA Pigtail
  • X4 M3 Hex Nut

Product Usage Instructions:

Step 1: Guards Pre-assembly

1. Start the assembly by using the bottom guards and install the
   29mm standoff with the M3x6mm screws.

2. Assemble the landing gear with an M3x14mm screw running inside
   the nylon insert and the landing gear tube.

Step 2: Bottom Plate Pre-assembly

1. Assemble the mid guard with the M3x6mm screws to close the
   guard assembly.

2. Add the 15mm standoffs for the guard braces.

Step 3: Top Plate Pre-assembly

1. Secure the aluminum parts to the bottom plate using M3x6mm
   screws.

2. Attach the isolation camera mount on the front, the bone in the
   middle, and the rear bracket at the back.

3. Stick the battery foam pad to the bone.

4. Check the orientation of the isolation camera mounts depending
   on the camera you want to use.

Step 4: Camera Isolation System Assembly

1. Mount the video transmission system using the previous
   assembly.

2. Replace the stock screws from the DJI O3 unit with M1.6x12mm
   screws to secure the vtx to the bottom plate.

3. Assemble the camera isolation system and bolt it to the bottom
   plate using M2x5mm screws.

Step 5: Flight Controller Installation

1. Install the flight controller to the bottom plate using M3x16mm
   screws.

2. Secure it with M3 hex nuts.

Step 6: Final Assembly

1. Mount the ESC to the top plate using M3x16mm screws and M3 hex
   nuts.

2. Solder the 10AWG wires and run them to the back where the XT-90
   panel mount sits inside the XT-90 aluminum, using M3x6mm
   screws.

product manual

table of contents
step # 1 guards pre-assembly step # 2 bottom plate pre-assembly step # 3 top plate pre-assembly step # 4 core assembly step # 5 guards assembly step # 6 final assembly

parts needed for this assembly
X2

guards pre-assembly
X2

BOTTOM GUARD

MID GUARD

X34
M3x6mm screws

X6
M3x14mm screws

X18 X4

M3x15 standoff

M3x29mm standoff

X6
carbon fiber tube

X6 nylon insert

landing gear

M3x29mm standoff

LANDING GEAR ASSEMBLY
CARBON FIBER TUBE

NYLON INSERT

M3x14 SCREWS

diag #1

M3x6mm screws

BOTTOM GUARD

1. Start the assembly by using the bottom guards and install the 29mm standoff with the M3x6mm screws.
Assemble the landing gear with a M3x14mm screw running inside the nylon insert and the landing gear tube. diag #1

M3x15 standoff

MID GUARD

M3x6mm screws

2. assemble the mid guard with the M3x6mm
screws to close the guard assembly. finish this step by adding the 15mm standoffs for
the guard braces.

parts needed for this assembly

X1

X2

bottom plate pre-assembly

X1

X2

X2

bottom plate

rear bracket

bone

isolation camera mount

battery foam pad

X1

X2

X4

X4

X2

X4

X10

X2

X4

dji O3 air unit heat sink set

isolation camera
plate

M1.6x12mm screws

M2x5mm screws

M2x8mm screws

M3x6mm screws

M3x16mm screws

M2 rubber grommet

M3 hex nut

battery foam pad
rear bracket

isolation camera mount
bone
bottom plate

isolation camera mount orientation

O3 / 20mm camera setup

19mm camera setup

diag #2

M3x6mm screws

3. Use the M3x6mm screws to secure the aluminum parts to the bottom plate. the isolation camera mount attaches on the front, the bone attaches in the middle and the rear bracket attaches to the back. Stick the battery foam pad to the bone, this is where the battery is going to rest inside of the frame.
Check the orientation of the isolation camera mounts depending on the camera that you want to use. diag #2

dji O3 air unit heat sink set

M2x5mm screws

camera isolation system assembly
M2 rubber grommet

isolation camera
plate

DJI O3 camera

M2x8mm screws

diag #3

M1.6x12mm screws

4. Use the previous assembly to mount the
video transmission system. Remove the stock
screws from the DJI O3 unit and replace them with the M1.6x12mm screws to secure the vtx to the bottom plate. Assemble the
camera isolation system and bolt it to the bottom plate by using M2x5mm screws.
diag #3

M3 hex nut
M3x16mm screws
5. To conclude this assembly, install the flight controller to the bottom plate by using M3x16mm screws and secure it with M3 hex nuts.

parts needed for this assembly
X1

top plate pre-assembly
X2

top plate

core plates

X1

X1

X2

X1

X2

X2

X2

X4

X6

x2

XT-90 mount X1

XT-90 pannel mount

cable bracket

XT-30 mount set

X1

X4

X4

XT-30

10AWG

connector power wire

X7

X7

18AWG power wire

motor washer plate

X7

X16

X16

universal washer

sma pigtail

X4 X4

crossfire horizontal
mount

crossfire vertical
mount

M3 hex nut M2x6mm screws

M3x6mm screws

M3x8mm screws

M3x10mm M3x6mm screws screws

M3x8mm screws

M3x16mm screws

M3x25mm screws

top plate

XT-90 mount

cable bracket

M3x16mm screws

XT-90 pannel mount

esc XT-90 wiring
esc 10AWG power wire

diag #4

M3x6mm screws

M2x6mm screws

M3 hex nut

6. Use the M3x16mm screws and M3 hex nuts to mount the esc to the top plate, solder the 10AWG wires and run them all the way to the back where the XT-90 pannel mount sits inside the XT-90 aluminum using M3x6mm screws. diag #4
Secure the wires using 2 cable brackets mounted with M2x6mm screws.

M3x6mm screws

motor spacer mount
M3x8mm screws
motor washer plate motor
diag #5

motor

7. Depending on the motor size that you are using, a spacer must be used to clear the propeller. If the motor is tall enough, use
M3x6mm screws to mount it to the top plate. if the motor is not tall enough,
install the motors using the motor washer
plate and the M3x8mm screws. diag #5

XT-30 mount set

XT-30 connector
18AWG power wire

8. Install the XT-30 mounts to the top plate by pushing them into the cutouts. Solder the 18AWG wires to the XT-30 connectors and then push them in place into the TPU mounts.

universal gopro mount

top plate

mounting pattern bottom plate

25×25 mounting pattern
30×30 mounting pattern
20×20 mounting pattern

dji O3 adapter plates

XT-90 mount

core plates
bottom plate pre-assembly

core assembly top plate pre-assembly
9. Use the core plates to join the bottom plate and top plate preassemblies together. Check the orientation of the core plates so to ensure the cutouts follow the tabs of the top plate and the openings to run the wires from the electronics.

M3x25mm screw
crossfire vertical
mount

M3x6mm screws

M3x10mm screws

crossfire horizontal
mount

M3x8mm screws
M3x6mm screws

10. Start by closing the frame using M3x6mm screws in the bone and the front of the top plate. Add the Crossfire horizontal mount using a M3x8mm screw.
Secure the XT-90 mount to the top plate by using the M3x10mm screws. add one universal washer and mount the crossfire vertical mount by using a M3x25mm screw.

guards assembly

guards pre-assembly main body

guards pre-assembly

11. Use the guards pre-assembly
to complete the structure of the frame. use the tabs of
the guards to insert them
into the cutouts of the core plates.

M3x8mm screws

final assembly
M3x6mm screws
12. Add the M3x6mm screws to the braces of the top plate , and add the M3x8mm screws to the bottom plate.

universal gopro mount

lipo strap

sma pigtail

13. Locate the holes on the guards and secure the sma pigtail using the included metalic washers.
Add the accessories, such as gopro mount and lipo strap.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>