FULGOR MILANO FCLHD 8041 Induction Vitroceramic Hob Instruction Manual

FCLHD 8041 HID TS BK 2
induction vitroceramic hob
INSTRUCTIONS FOR INSTALLATION AND USE
PICTURES

PRODUCT DESCRIPTION

1. – HOB
2. – METAL GRID
3. – FILTERING CASE
4. – ELECTRICAL WIRING

WARNING

• This appliance cannot be used by people (including children) with impaired physical, sensory or mental abilities or with a lack of experience and knowledge, unless they are supervised or unless they are given instructions about the use of the appliance by a person responsible for their safety.

• Kids aged less than 8 years old must be kept away from the appliance unless they are under constant surveillance.

• Kids must not play with the appliance.

• Cleaning and maintenance of the appliance must not be carried out by kids without any supervision.

• This appliance can only be used in combination with S-H3 induction hobs.

• The room must be adequately ventilated if the hood and other appliances powered by energy other than electricity are used at the same time. This prevents the hood from sucking in any combustion fumes.

• It is forbidden to cook food over open flames, as sucked flames are a risk of damage to the appliance.
  WARNING: This appliance and its accessible parts are likely to become very hot if used in combination with cooking devices.

• After 30 hours of operation, the speed indicators of the appliance will signal that the grease filters need cleaning.

• The cleaning of the grease filters and their saturation time span must be respected. Grease deposits and build-ups are a risk of fire.

• The hood must not be operated without the grease filters.

• The exhausted air must not be conveyed in a duct used for discharging fumes of appliances powered by energy other than electricity (heating systems, etc.).
  WARNING: This appliance is not intended to be used with gas hobs.

• To discharge the exhausted air, regulations issued by competent authorities must be followed.

• If the product is not equipped with a plug or if, at the end of the installation, the plug is not easily accessible, it is necessary to arrange a device separating the product from the electrical system. The contacts of this device must have an opening distance of all the poles of at least 3 mm.
  WARNING: Do not store liquids in the cabinet, under the induction hob, where the electrical components of the appliance are located. Leaks or spillovers on the electrical parts of the appliance are a cause of electrical shocks.
  Carrying out the cleaning operations without following the instructions is a risk of fire.

FIRE RISK: Do not store any flammable material in the cabinet, under the induction hob, where the electrical components of the appliance are located.
Do not pull the electrical wires.
The flat cable connecting the main wiring assembly to the hob must be placed on the rear of the hob, to preserve it from any breakage.
A distance of at least 15 cm must be left between any object, stored in the same cabinet where the appliance is installed, and the lower part of the induction hob. In fact, the airflow coming from the cooling system in the lower part of the induction hob must not be hindered.

• Do not modify or try to modify the characteristics of this appliance, as this is dangerous. Any repair must be carried out by authorized personnel. The hoods must always be disconnected from the power supply before performing any cleaning or maintenance operation.
• The controls locking device must be used to prevent children from accidentally turning on the appliance or switching its functions. The appliance must never remain unattended while it is operating.
• Should the product show any anomaly, disconnect the appliance from the power supply.
• Before carrying out the installation of the appliance, please check that all components are not damaged. In such a case, make contact with your retailer and do not proceed with the installation.
  – Do not try to modify or repair the appliance, as this might entail great danger.
  – The grease filter can be washed either by hand or in the washing machine. The filters are to be cleaned according to the use, but at least once every two months.
  – The charcoal filter must be replaced according to the use, but at least once every six months.

PRODUCT INSTALLATION

Before any installation operation is carried out, make sure that the appliance is disconnected from the power supply.

TECHNICAL OPERATIONS
Place the overturned hob on an adequate surface, preserving the glass from any scratches. Take the filtering case out of the packaging and install it as shown in Fig. 1. The metal hooks of the filtering case are to be inserted in the specific slots, located on the rear of the hob, as shown in fig. 2. After having hooked the filtering case to the hob, fix it by means of the provided metric screw, to be used as shown in Fig. 3.
Carry on the installation by securing the hob to the cabinet, as shown in the specific user manual provided within the packaging of the hob.

IN CASE OF RECIRCULATING OPERATION (Fig. 4)
The air outlet of the product must be connected to the opening in the cabinet so as to recirculate the exhausted air in the kitchen. Charcoal filters, to be purchased separately, are needed in this configuration. They must be installed as shown in Fig. 6. Charcoal filters are located right under the grease filters, so they must be installed before the grease filters. A ducting kit with a grill (on the end to be installed in the cabinet) is also available for separate purchase.

IN CASE OF DUCTING OPERATION (fig. 5)
The air outlet of the product must be connected to the outside of the house. The ducting to be installed from the air outlet of the product to the outside of the house is not provided with the appliance. The product is equipped with plastic flanges, to connect ducts of sections 220×90 mm.

FINAL OPERATIONS
Install the grease filters in the specific seat, letting them through the central opening of the hob, see Fig. 7.
To close the central opening of the hob, place the metal grill on top of it, as shown in Fig. 8.

ELECTRICAL CONNECTIONS
The connection of the product to the power supply must be carried out in compliance with the international and local regulations in force.
The interconnection of any separate part of this appliance must be carried out by a qualified technician in compliance with the wiring regulations.
The connection to the power supply must be by means of a plug and it can also be done by the end user.
Any liability in case of accidents caused by failure to arrange the earth connection or failure to arrange it correctly is hereby declined.
The controls located under the glass of the hob have a cable, which must be connected to the control box (Fig. 9).

CLEANING AND MAINTENANCE

Before carrying out any cleaning or maintenance operation, the appliance must always be disconnected from the power supply.

• Should the power cord endure any damage, it can only be replaced by after-sales service or by experienced personnel.

Do not try to modify or repair the appliance, as this might entail great danger. Service or repair operations must be carried out by experienced personnel.
In case of anomalies, the appliance must be disconnected from the power supply.
Cleaning and maintenance operations must not be carried out by children without supervision.
Accurate maintenance is a guarantee of proper function and good performance of the appliance over time.
The grease filter can be cleaned either by hand washing or by washing machine.
Filters cleaning occurs according to the use, but at least once every two months.
Replacing the charcoal filters occurs according to the use, but at least once every six months.
Tepid water and mild soap are recommended while cleaning the appliance. Abrasive products must be avoided.

BEFORE STARTING. PRELIMINARY RECOMMENDATIONS OF THE MANUFACTURER

Keep these instructions with the appliance. Should the appliance be sold or passed on to others, make sure that it is accompanied by these instructions? We thank you for paying attention to these recommendations before installing and using the appliance, as they have been written for your safety and that of others.
Upon delivery of the product, the packaging and its general aspect must be checked. Any objections must be written on the delivery document, of which you must keep a copy. The appliance is destined for normal domestic use. It must not endure any commercial or industrial use and it cannot serve any other purpose different from the one it has been designed for.
No warranty will be provided for any damages or other consequences originating from an incorrect installation or a misuse of the appliance.
With the aim of constantly improving our products, we reserve ourselves the right of modifying their technical, functional, and aesthetic features. The appliance is already arranged to work either in recirculating or ducting mode. Before proceeding with the installation, all components of the appliance be checked. In case of damaged or missing components, make contact with the retailer and do not proceed with the installation. In ducting operation, a maximum of 5 meters long ducting is allowed. The number of elbows must be limited, as each curve diminishes the ducting efficiency of 1 linear meter (e.g. if you use 2 elbows by 90°, the length of the ducting must not exceed 3 meters of length). Avoid any abrupt change of direction in the ducting.
The ducting connected to the blower air outlet must have a constant section of 220×90 mm. The ducting must be made of a material approved by the regulations in force. Failure to respect the above-mentioned instructions might result in performance or noise problems, for which no warranty will be provided.

ENERGY LABEL AND ECODESIGN REGULATIONS
As the EU Commission Regulations No. EU65 “Energy Label” and No. EU66 “Ecodesign” came into force on the 1st January 2015, the products have been updated, so that they can be compliant and meet the criteria of the regulations. All products in the Energy Label version are equipped with electronics able to temporize ducting speeds that are over 650 m3/h.

FUNCTIONS

Touch controls (Fig. 10).
A: ON/OFF switch. It allows to turn on the product and it automatically sets it on the second speed. When the appliance is on, at any speed level, this turns off the blower.
B: linear touch control that allows changing the blower speed. It is not possible to turn off the blower by means of these controls. It is not possible to select a speed level unless the product has been turned on using the ON/OFF key.
C: LED indicators, showing what blower speed has been set.
D: 10 minutes after this key has been touched, the blower stops itself. When this function is on, it is signaled by the blinking of the “C” LED, according to the speed that has been set.

Automatic switch off: After 4 hours of uninterrupted operation, or after 4 hours since the last key has been touched, the appliance turns off automatically.
Grease filter saturation: After 30 hours of operation, all speed indicators blink simultaneously (Fig. 10C), to signal the saturation of the grease filters. By holding the TIMER key for at least three seconds when the product is turned off, the alarm goes off and it is reset.

  The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product. This appliance is marked according to the European directive 2012/19/EC on waste electrical and electronic equipment (WEEE).

–SINCE 1949–
DOC COD.
3.000.047.0-03/22
90007770006 – 03/22

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>