ALPINE SWC-D84S Subwoofer Installation Guide

June 3, 2024
Alpine

ALPINE SWC-D84S Subwoofer Installation Guide
ALPINE SWC-D84S Subwoofer

Optional SWA-150KIT Amplifier & Controller Kit

Amplifier & Controller Kit

Parts list

Subwoofer enclosure
Parts list

Metal bracket incl. screws
Parts list

Head unit adapter harness
Parts list

Coil-adapter sub woofer (not needed in combination with optional SWA-150KIT)
Parts list

  1. Remove the two round  screw covers and the T25 screws in the upper part of the cupholder.
    Parts list

  2. Remove the rubber layer  from the cupholderand the T25 screw.
    Parts list

  3. Pull out the whole cupholder part (In case there is a USB-jack remove it in advance).
    Parts list

  4. Remove the six T26 screws
    Parts list

  5. Remove the center console plastic bracket.
    Parts list

  6. Remove the two T25 screws from the lower plastic panel.
    Parts list

  7. Don‘t remove the lower plastic panel because here the metal bracket of the SWC-D84S will be fixed.
    Parts list

  8. Take the metal bracket of the subwoofer enclosure and insert the cable of the subw. coil-adapter throw the hole inside the bracket.
    Parts list

  9. Fix the subw. coil-adapter with the two cable ties to the provided holes inside the sub woofer metal bracket.
    Parts list

  10. Fix the metal bracket with the two screws to the lower cover  and connect the cable from the head unit harness to the coil adapter connector.
    Parts list

  11. Use the two original screws  to fix the metal bracket and the lower plastic cover.
    Parts list

  12. To reach the above screws more easy plaease move the lower plastic cover to the front.
    Parts list

  13. Insert the center console plastic bracket.
    Parts list

  14. In case you‘ll install also the SWA-150KIT please proceed first with installation step 26

  15. Fix the center console plastic bracket with the six screws. The two lower screws will fix  also the bracket of the
    sub woofer enclosure.
    Parts list

  16. Fix the cup holder with the three T25 screws and insert the rubber inlay.
    Parts list

  17. Sub woofer enclosure.
    Parts list

  18. Connect the speaker cable which you passed through the hole inside the metal bracket before.
    Parts list

  19. Bring the enclosure into the position in front of the metal bracket
    Parts list

  20. Shift the enclosure into the metal bracket. Be carefule with the speaker  cable to avoid to squeeze it!
    Parts list

  21. Fix the enclosure with the four attached screws. Two on each side. Take care about the different screw sizes!
    Parts list

  22. The installation of the subwoofer enclosure is compleated.
    Parts list
    Needed installation steps when the radial front speakers SPC-R100-DU are installed

  23. Before you start the operation, you’ve to disconnect the original Fiat (PSA) door speaker. Please remove carefully the speaker grill from the door panel.
    Parts list

  24. Unplug the connector from the speaker.
    Parts list

  25. Store the speaker connector in this area and fix it with tape.
    Parts list
    Needed installation steps when the amplifier & controller kit SWA-150KIT is installed

  26. WA-150KIT
    Amplifier & Controller Kit
    Parts list

  27. Open the vehicle battery compartment in front of the  driver seat by unlock the six plastic screws.
    Parts list

  28. Insert the amplifier power cables (+/-) into the battery compartment.
    Parts list

  29. Connect the red (+) cable to the plus terminal of the vehicle battery.
    Parts list

  30. Connect the black (-) cable to the GND-terminal of the vehicle battery.
    Parts list

  31. Stick the amplifier with the included self-adhesive Velcro pads to the plastic center console bracket.
    Parts list

  32. Pass the power cable from the battery compartment to the amplifier location in the center console bracket.
    Parts list

  33. Stick the controller with the self-adhesive Velcro pads at the provided position and  pass the cable to the amplifier.
    Parts list

  34. Pass the speaker cable behind the center console bracket to the already installed head unit adapter cable and insert the connectors.
    Parts list

Product Parameter

In case you’ll combine the “ALPINE Crescendo or Concert Ensemble” Sound system with one of the below listed ALPINE Multimedia Systems you can increase the sound performance by the right setup of your DSP parameter (follow the settings listed in below table)
Parameter

The cup holder center console is mandatory for the installation of the Sub woofer Enclosure!
In case your vehicle isn’t equipped with this cup holder please order the part from your FIAT dealer.

Cup holder Center Console
(FCA Part-No.: 71807349)
Cup holder Center Console

Support

ALPS ALPINE EUROPE GmbH
Ohmstrasse 4
85716 Unterschleißheim
Germany

For contact information on your respective country, please visit www.alpine- europe.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals