Polibi WF198565 White Twin Over Twin Low Bunk Bed Instruction Manual
- June 5, 2024
- Polibi
Table of Contents
WF198565 White Twin Over Twin Low Bunk Bed
Instruction Manual
ASSEMBLY INSTRUCTIONS
SAFETY WARNINGS
- Follow the information on the warning label appearing on the upper bunk bed and structure on the carton … Do not remove the warning label from the bed
- Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls
- The surface of the mattress must be at least 5 inches below the upper edge of the guard rails
- Do not allow children under 6 years to use the upper bunk bed.
- Prohibit more than one person on the upper bunk.
- Periodically check and ensure that the guardrail, ladder, and other components are in their proper position, free from damage and that all connectors are tight.
- Do not allow horseplay on or under the bed and prohibit jumping on the bed.
- Always use the ladder for entering and leaving the upper bunk.
- Do not use substitute parts. Contact the manufacturer or dealer for a replacement part.
- Use of a night light may provide added safety precautions for a child using the upper bunk.
- If the bunk bed will be placed next to a wall, the guardrail runs the full length of the bed.
- Always use a guardrail on both long sides of the upper bunk.
- The use of water or sleep flotation mattresses is prohibited.
- Keep these instructions for future reference.
- Stranqulation Hazard – Never attach or hang items to any part of the bunk bed that is not designed for use with the bed, for example, but not limited to hooks, belts and jump ropes.
If you have any questions about the product,
please contact the email: Polibihd@outlook.com
Detail View
Part List :198565
Part List:198566
Hardwear List :198566
PLEASE BE CAREFUL NOT TO DAMAGE THE HOLE POSITION WHEN YOU USE POWER TOOLS!
STEP 1: Following the below illustration Assembly FRAME #1. Using hardware #9 connect T and W front panel (left-right) with T1 short decorative bar to complete FRAME #1LR, And using hardware #9 connect the U and V front panel (upper-lower) with U1 long decorative bar to complete FRAME
1UL.![Polibi WF198565 White Twin Over Twin Low Bunk Bed - Fig
1](https://manuals.plus/wp-content/uploads/2022/07/Polibi-WF198565-White-Twin- Over-Twin-Low-Bunk-Bed-Fig-1.jpg)
STEP 2: Following below illustration Assembly FRAME #2. Using hardware #8 connect T and W front panel (left-right) with V and U front panel (upper-lower middle) to complete FRAME #2.
STEP 3: Following below illustration Assembly FRAME #3. Using hardware #4 connect S horizontal bar (front) with FRAME #2 to complete FRAME #3.
NOTE: In this step, DO NOT tighten any bolt until you connect all part
together
STEP 4: Following below illustration Assembly FRAME #4. Using hardware #1
& #5 connect H vertical middle front with FRAME #3 to complete FRAME #4.
NOTE: In this step, DO NOT tighten any bolt until you connect all parts
together
STEP 5: Following the below illustration Assembly FRAME #5. Using
hardware #6 connect J HB cap side (back) with I HB cap side (front) to
complete FRAME #5H6 and L cap middle with K cap middle to complete FRAME #5MB.
NOTE: in this step, DO NOT tighten any bolt until you connect all parts
together
STEP 6: Following the below illustration Assembly FRAME #6.
Using hardware #1 & #5 connect Y1 and Y2 stairs vertical left-right with Z
stairs bridge to complete FRAME #6.
STEP 7: Following below illustration Assembly FRAME #7.
Using hardware #1 & #7 connect A and B FB leg front-back with E and F lower-
upper horizontal bar to complete FRAME #7.
NOTE: in this step, DO NOT tighten any bolt until you connect all parts together
STEP 8: Following the below illustration Assembly FRAME #8. Using
hardware #1 & #7 connect C and D HB leg front-back with E and F lower-upper
horizontal bar
to complete FRAME #8.
NOTE: in this step, DO NOT tighten any bolt until you connect all parts together
STEP 9: Following the below illustration Assembly FRAME #9.
Using hardware #6 connect FRAME #5HB with FRAME #8 to complete FRAME
9.![Polibi WF198565 White Twin Over Twin Low Bunk Bed -
Fig9](https://manuals.plus/wp-content/uploads/2022/07/Polibi-WF198565-White- Twin-Over-Twin-Low-Bunk-Bed-Fig9.jpg)
NOTE: in this step, DO NOT tighten any bolt until you connect all parts together
STEP 10 : Following below illustration Assembly FRAME #10. Using hardware
1, #2 & #6 connect FRAME #7, #9 with M, N, O side rails and P long side
horizontal bar to complete FRAME #10.
NOTE: in this step, DO NOT tighten any bolt until you connect all parts together
STEP 11: Following the below illustration Assembly FRAME #11. Using
hardware #1, #5 & #6 connect R horizontal bar back and G vertical middle back
to complete FRAME #11. NOTE: in this step, DO NOT tighten
any bolt until you connect all parts together
STEP 12: Following below illustration Assembly FRAME #12.
Using hardware #5 connect O side rail and P long side horizontal bar with G
vertical middle back to complete FRAME #12.
STEP 13: Following the below illustration Assembly FRAME #13.
Using hardware #1 & #6 connect FRAME #9 with FRAME #4 to complete FRAME
13.![Polibi WF198565 White Twin Over Twin Low Bunk Bed -
Fig13](https://manuals.plus/wp-content/uploads/2022/07/Polibi-WF198565-White- Twin-Over-Twin-Low-Bunk-Bed-Fig13.jpg)
NOTE: in this step, DO NOT tighten any bolt until you connect all parts together
STEP 14: Following the below illustration Assembly FRAME #14.
Using hardware #6 connect FRAME #14MB with FRAME #13 to complete FRAME
14.![Polibi WF198565 White Twin Over Twin Low Bunk Bed -
Fig14](https://manuals.plus/wp-content/uploads/2022/07/Polibi-WF198565-White- Twin-Over-Twin-Low-Bunk-Bed-Fig14.jpg)
NOTE: in this step, DO NOT tighten any bolt until you connect all parts
together
STEP 15: Following the below illustration Assembly FRAME #15. Using
hardware #4 connect X top panel with FRAME #14 to complete FRAME
NOTE: in this step, DO NOT tighten any bolt until you connect all parts
together
STEP 16: Following the below illustration Assembly FRAME #16.
Using hardware #1 & #5 connect FRAME #6 and Q short side horizontal bar with
FRAME #15 to complete FRAME #16.
STEP 17: Following below
illustration Assembly FRAME #17.
Using hardware #5 connect FRAME #6 (Y2 stairs vertical right) with B FB leg
front to complete FRAME #17.
NOTE: in this step, DO NOT tighten any bolt until you connect all parts
together
STEP 18: Following the below illustration Assembly FRAME #18.
Using hardware #5 connect M upper-lower side rail (front) with Y1 stairs
vertical left to complete FRAME #18.
NOTE: in this step, DO NOT tighten any bolt until you connect all parts together
STEP 19: Following the below illustration Assembly FRAME #19.
Using hardware #8 connect to screw all wood slat A1, B1 with FRAME #18 on all
the Bed.
WARNING!:
Please completed screw all the slats into the side rails before using.
COMPLETED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>