HESSAIRE W6100 Window Evaporative Cooler User Guide

General Safety Precautions

WARNING: Read and follow all instructions, cautions and warnings. Failure to do so could result in personal injury, death or property damage and could void the warranty.

Use only with a 115v, 60Hz, Single Phase grounded circuit.
Always unplug the unit and switch to off position when servicing.
Use qualified electricians when replacing electrical components.
Do not operate with rear media panel or front guard/louvers removed.
Do not operate with damaged power cords, outlets or other visible damage.
Do not route the power cord under carpet or other flooring.
Do not use with plug adapters or 2 prong connectors.

To reduce risk of electrical shock or fire, DO NOT use with any solid state speed control device.

Getting Started

Contents:

• (1) cooler unit,
• (1) hardware pack,
• (1) manual

Suggested Tools/Materials Needed:

• Drill
• Adjustable Wrench
• Drill Bits For Mounting Screws

• 2 Phillips Screwdriver

• Caulking/Sealant
• 1/4” Plastic Drain Tubing
• Support Brackets
• Spacer material: wood strips

Unpacking:

Carefully unpack and inspect the entire unit prior to installing. Ensure there is no visible damage and all contents are included.

Note: The fan assembly portion that protrudes into living area is recessed for shipping purposes.

1. Pull fan assembly outward (approx. 9”) and fasten in place with the 12 provided screws.

2. Remove back panel.

3. Remove and discard both side cardboard pad protectors (cardboard pieces protect media pads while extending).

4. Extend out and fasten in place.
   

5. Remove back panel.

6. Remove & discard cardboard protectors.
   

Installation

DO NOT connect power until installation is complete.

Installing In Window: With assistance, insert fan duct part of cooler through window. See Fig. 2A

Outside tank part of cooler should fit as tight to wall as possible and should be level.
Note: It may be necessary to utilize a wood spacer to keep unit straight up and down when fastening to uneven siding. Wood stip not included. See Fig. 2A.

While holding cooler in correct position, fasten to the wall through designated screw holes on bottom outside unit.
Note: It is suggested to use support brackets on under outdoor unit for additional support. Brackets are not included.

Lower window securely on fan duct. Fill the open window gap(s) on the sides of the duct going through the window. Plywood or paneling is recommended. Sealant is recommended to hold panels in place and seal any gaps.

Plug unit into 115v grounded outlet. Connect water supply to the exterior part of unit. Unit is ready to power on.

Installing Through Wall: Consult a qualified contractor to frame in opening. Follow steps above for fastening to outside wall and using support brackets. Refer to rough-in dims shown below. Fig. 2B.

Operation

Operating Tips:

It is critical for optimum operation of the window cooler that there is sufficient air openings for the area to be properly cooled. Opening doors or windows usually accomplishes this.

For best ventilation results, it is important that doors and windows are not open on the windward side of the house.

Rooms further away from the cooler typically require more ventilation than rooms closest to the cooler.

Control Functions

Specifications

Model

| Speed| High CFM| Low CFM| Volts| High Amps| Low Amps| Watts| Phase|

Operating Water Pressure

---|---|---|---|---|---|---|---|---|---

W6100

| 2| 6700| 4020| 115| 3.6| 2.9| 320| 1|

60 PSI

Dimensions

Model

| Dim.A| Dim.B| Dim.C| Dim.D| Dim.E| Dim.F| Dim.H| Dim.K|

Dim.W

---|---|---|---|---|---|---|---|---|---

W6100

|  21 5/8”| 21 5/8”| 10”| 26 3/4″| 10”| 3 3/4″| 35 1/2”| 3 5/8”|

29 1/4”

Maintenance

WARNING: Disconnect from power source before attempting any maintenance or routine service. NEVER remove any access panels while unit is in operation or plugged in. Failure to do so could lead to SERIOUS INJURY.

Accessing Components:

1. Remove 2 phillips screws
2. Push back panel up
3. Pull bottom of panel out to remove.
   

Cleaning And Storage:

Remove pads for cleaning. Use a soft brush. Vinegar may be used.
Drain tank and wipe dry.
Ensure pads are dry by running fan for at least 30 minutes without the pump.

Troubleshooting

Problem

|

Cause / Remedy

---|---
Cooler won’t turn on| Ensure unit is plugged in and switched on.
Receptacle breaker may need to be reset.
If unit is equipped with a GFCI plug, reset.
If unit has a timer, ensure it is off.
May need new ON/OFF switch.
Fan will not operate| Ensure fan function is on.
Make sure nothing is obstructing fan blade.
Fan motor may need to be replaced.
Fan switch may need to be replaced.
Slow running – may need capacitor replaced.
Cooler does not pump| Ensure pump switch is turned on.
Make sure water level is not low. Add water.
Make sure hoses are connected and free of debris.
Pump may need to be replaced.
Swing does not work| Ensure swing switch is turned on.
Make sure the linkage is connected.
Oscillation switch may need to be replaced.
Oscillation motor may need to be replaced.
Water leakage| Make sure drain plug is securely in place.
Make sure cooler is level.
Inspect tank for cracks.
Check media pads for water running on outside of unit. Change pads if necessary.
Check for leaks in water distribution hose connections.
Check spreaders for build up causing spill over of water into the airstream.
| Float valve needs to be adjusted to keep water level below overflow.
Water level high or low| Adjust nut on float valve.
Float valve may need to be replaced.

Parts Illustration

#

| Parts Description| W6100
---|---|---
1| Pump|

6060050

2

| Oscillator Motor| 6375700
3| Control Panel|

W67CP

4

| Media Pad Set| CP610
5| Float Valve|

857023

6

| Motor, 6 pole, 2spd| B180-62W67
7| Prop (fan blade)|

9001705

8

| Nylon threaded drain with overflow| 14216
9| Silicone drain plug|

6017081

Hessaire Warranty

Each new cooler is warrantied to be free from defects in material or workmanship for one full year from the date of original purchase. If a component(s) is found to be defective within this period, the defective part will be provided free of charge. Replacement parts are available through authorized dealers or online. Copy of proof of purchase and serial label number will be needed for all warranty claims.

What is not covered:

Malfunctions resulting from misuse, negligence, alteration or lack of
necessary maintenance.

Loss of time, inconvenience, use of product or other consequential damages due to defects.

Return transportation costs. All return costs are the responsibility of the purchaser.

Hessaire does not cover labor costs associated with troubleshooting or cooler repairs regardless if the product is under warranty or not.

Damaged Shipments:
Hessaire is not responsible for damaged shipments or shortages resulting from carrier mishandling. Notify your carrier’s office immediately to file a freight claim in the event of damage. Keep damaged product for inspection until advised by carrier as to disposal.

Please DO NOT return your cooler to Hessaire. Upon authorization, any returns should be sent directly to the distributor/store where purchased.

Instructional videos and other helpful parts replacement information is available onhessaire.com.
Visithessaire.com for warranty claim forms.

References

• Hessaire.com - Cool Air Anywhere!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>