JBC NASE-9C NAS 2-Tool Nano Rework Station Instruction Manual
- June 5, 2024
- JBC
Table of Contents
INSTRUCTION MANUAL
NAS
2-Tool Nano Rework Station
This manual corresponds to the following references:
– NASE-9C (100V)/- NASE-1C (120V )
– NASE-2C (230V)
Packing List
The following items are included:
Features and Connections
Tool Stand Assembly
Tool Stand Replacement
Loosen the screw (1) and withdraw the to stand (2) .
Insert the new tool stand (3) and tighten the screw (4).
Work Screen
The DDE offers an intuitive user interface that provides quick access to
station parameters.
Default PIN: 0105
Troubleshooting
Station troubleshooting is available on the product page at
www.jbctools.com
Advanced Functionalities
| It provides detailed graphics of tip temperature and power delivery in real-
time during solder joint formation for analysis purposes. This helps you
decide how to adjust your process or which tip to use to obtain the best
quality soldering.
---|---
| Designed to avoid thermal shock when soldering Ceramic Chip components like
MLCC, this new and unique feature allows controlling the heating ramp-up rate
of the tool to gradually increase the temperature of the component through all
the phases of the soldering process. Up to 25 fully confi durable soldering
profi les can be stored.
| Get greater quality and control in your production. Manage your whole
soldering process remotely in real-time.
For more information see
www.jbctools.com/webmanager.html.
| Export graphics
Insert a USB flash drive into the USB-A connector to save your soldering
process in CSV format.
| Station update
Download the JBC Update File from
www.jbctools.com/software.html Insert the
USB flash drive with the file downloaded to the station.
System Notifications
The following icons will be displayed on the screen’s status bar.
| USB fl ash drive is connected.
---|---
| The station is controlled by a PC.
| The station is controlled by a robot. downloaded to the station.
| Station software update. Press INFO to start the process.
| Warning. Press INFO for failure description.
| Error. Press INFO for failure description, the type of error, and how to
proceed.
Operation
This revolutionary technology is able to recover tip temperature extremely
quickly.
This allows the user to work at a lower temperature.
As a result, tip life increases by 5.
When the tool is lifted from the holder the tip will heat up to the selected
temperature.| When the tool is in the holder, the power is cut off and the
tool cools down to room temperature.
· Set temperature limits
· Set temperature levels| · Set Hibernation delay (from 0 to 60 min or no
Hibernation)
Example:
Chip Components Rework Process using Tweezers and Pedal
The Pedal is frequently used to rework components with tweezers.
AN115 JBCs adjustable nano tweezers is the most effective tool for desoldering
chip components but also it facilitates its rapid placement and soldering by
using the P405 pedal connected to JBC´s NAS station.
Connections
Connect pedal P405 to the same port where AN115 nanotweezers are connected.
In the peripherals menu for the “Pedal Activation Mode” choose between
“pressed”and “released”.
- “Press Mode” previously selected
**Desoldering*
Lift the tool from the holder, press and hold the pedal to activate the tool, and desolder the component.
Once the pedal is released the tool enters hibernation mode and cools down.
Pad Cleaning**
Clean the pads with JBC´s desoldering tool DS360.
For this operation JBC´s desoldering station DSS is needed.
Solder Paste Dispensing
Apply the solder paste amount needed to solder the new chip component.
The use of JBC´s DPM solder paste dispenser is recommended.
Placing
Do not press the pedal.
Use the tool to position the component on the previously tinned pad.
Note:
The inactive tool prevents the component from heating up prematurely.
Soldering
Once in position press and hold the pedal to activate the tool and perform the
soldering.
Changing Cartridges
Save time and change cartridges safely without having to switch the station off.
Place the cartridge into the extractor slot (1) and pull the handle to remove
them (2).| Push the cartridge into the handle until the mark*.| Use the holes
to rotate the cartridges for proper
alignment.
*Important
It is essential to insert the cartridges as far as the reference ring for a
proper connection.
Compatible Cartridges
The Nano Handle NT115 and the Adjustable Nano Tweezers AN115 work with C115
cartridges. Find the model that best suits your soldering needs on
www.jbctools.com
Changing Grips
1. Inserting
First, put the slide-on tabs into the new grip, then push the grip with the
tabs onto the handle.
2. Removing Tabs
Hold the grip and pull the tab. Use a pliers if necessary
Changing the Tip Cleaning System
Press back the tap (1) to remove the cleaning system (2).| Remove the drawer from the splashguard.
Maintenance
Before carrying out maintenance, always switch the device off and disconnect
it from the mains.
Allow the equipment to cool down.
– Clean the station screen with a glass cleaner or a damp cloth.
– Use a damp cloth to clean the casing and the tool. Alcohol can only be used
to clean the metal parts.
– Periodically check that the metal parts of the tool and stand are clean so
that the station can detect the tool status.
– Maintain tip surface clean and tinned prior to storage in order to avoid tip
oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
– Periodically check all cables and tubes.
– Replace any defective or damaged pieces. Use original JBC spare parts only.
– Replace a blown fuse as follows:
1. Pull off the fuse holder and remove the fuse. If necessary use a tool to
lever it off| 2. Press the new fuse into the fuse holder and replace it in
the station.
---|---
Safety
It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
– Do not use the units for any purpose other than soldering or rework.
Incorrect use may cause a fire.
– The power cord must be plugged into approved bases. Be sure that it is
properly grounded before use. When unplugging it, hold the plug, not the wire.
– Do not work on electrically live parts.
– The tool should be placed in the stand when not in use in order to activate
the sleep mode. The soldering tip or nozzle, the metal part of the tool, and
the stand may still be hot even when the station is turned off. Handle with
care, including when adjusting the stand position.
– Do not leave the appliance unattended when it is on.
– Do not cover the ventilation grills. Heat can cause inflammable products to
ignite.
– Avoid flux coming into contact with skin or eyes to prevent irritation.
– Be careful with the fumes produced when soldering.
– Keep your workplace clean and tidy. Wear appropriate protection glasses and
gloves when working to avoid personal harm.
– Utmost care must be taken with liquid tin waste which can cause burns.
– This appliance can be used by children over the age of eight and also
persons with reduced physical, sensory or mental capabilities or lack of
experience provided that they have been given adequate supervision or
instruction concerning the use of the appliance and understand the hazards
involved. Children must not play with the appliance.
– Maintenance must not be carried out by children unless supervised.
Specifications
NAS
2-Tool Nano Rework Station
Ref.: NASE-9C 100V 50/60Hz. Input fuse: 0.5A. Output: 8.5V
Ref.: NASE-1C 120V 50/60Hz. Input fuse: 0.5A. Output: 8.5V
Ref.: NASE-2C 230V 50/60Hz. Input fuse: 0.2A. Output: 8.5V
– Output Peak Power:14W per tool
– Temperature Range:90 – 450 °C /190 – 840 ºF
– Idle Temp. Stability (still air):±1.5ºC /±3ºF (meets and exceedss IPC
J-STD-001)
– Temp Accuracy: ±3% (using reference cartridge)
– Temp Adjustment:±50ºC / ±90ºF (through a station menu setting)
– Tip to Ground Voltage/Resistance: Meets and exceed ANSI/ESD S20.20-2014 IPC
J-STD-001F
– Connections:USB-A / USB-B / pedal connectors RJ12 connector for robot
Ambient Operating Temp: 10 – 50 ºC / 50 – 122 ºF
– Control Unit Dimensions:140 x 170 x 125 mm
(L x W x H): 5.51 x 6.69 x 4.92 in
– Total Net Weight: 2.49 kg / 5.49 lb
– Total Package Dimensions/Weight: 280 x 280 x 164 mm / 2.99 kg
(L x W x H) 11.02 x 11.02 x 6.46 in / 6.59 lb
Complies with CE standards
ESD Safe
Warranty
JBC’s 2-year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labor. The warranty does not
cover product wear or misuse. In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer where it was purchased.
Get 1 extra year of JBC warranty by registering here:
https://www.jbctools.com/productregistration/within 30 days of purchase.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility. a manuales – color gris
References
- JBC Soldering Stations, Irons and Rework equipment for electronics
- JBC Web Manager
- Warranty Extension
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>