CARRO CES523BL 52 Inch Smart Ceiling Fan Installation Guide

CARRO CES523BL 52 Inch Smart Ceiling Fan

SAFETY PRECAUTION:

IMPORTANT: PLEASE READ BEFORE INSTALLATION:

1. before you begin installing the fan, shut power off at the circuit breaker of the use box,

2. CAUTION: Read al instructions and safety information before installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrical connections are in accordance with National Electrical Code,
   ANSI/NFPA 70 and local codes. Hire a licensed electrician if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions.
   Alow a minimum clearance ot 2.1m ( teet) from the 1oor and 18 inches from the tip of the blades

5. WARNING: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “ACceptable Tor Fan Support or 15.s Kg (35 ID8) or less” and use mounting screws provided wn tne outlet box.

6. CAUTION: To reduce the risk of injury, use only the screws provided with the outlet box in
   conjunction with the lock washers provided with the fan. ne outlet Dox and support structure must be securely mounted and capable oT reliably supporting a minimum of 35 pounds. Use only U.L. listed outlet boxes marked “Acceptable for Fan Support of 15.9 kg (35 Ibs) or less.

7. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

8. Do not insert anything into the fan blades while the fan is operating.t be in operation mode.

9. All set screws must be checked and retightened where necessary before installation.

10. WARNING: To reduce the risk of personal injury, do not bend the blade bracket when installing the brackets, balancing the blades, or cleaning the tan. Do not insert foreign objects in between rotating tan blades.

11. CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan
    before installing light kit,

12. After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side of the outlet box.

13. The splices after being made should be turned upward and pushed carefully up into the outlet
    DOX. Conductor wiring widened as grounded is to De connected to a grounded conductor or power Conductor wiring identified for equipment grounding wg equipment grounding is to be connement grounding conductor.

BEFORE YOU START

Contact a licensed electrician ifyou are uncomfortable performing electrical work. A licensed electrician must install the fan if required by local code.
Do not use the fan with a dimmer switch. Turn off power at the breaker.

Product instruction:

Installation:

Installing the Fan Blades:
Locate 6 blade attachment screws with integrated washers, and bigger washers in the hardware pack.
Secure each blade to the blade arm with the screws and washers as shown in Fig 1.1.
Fig 1.2 is the schematic diagram of the installed fan blade arm. Repeat for the remaining blades.
Make sure all the screws are firmly tightened.

Installing the Prepared Fan Blade Arms:
Fix each prepared blade arm to the motor assembly with blade arm screws as shown in Fig 2.1.
Install the other blade arms with installed blades onto the corresponding mounting holes of the
motor, as shown in Fig 2.2.

Attaching the Downrod:
Assemble download as pictured in Fig.3.1. (Please select the suitable length of rod for your ceiling.
NOTE: If you choose to install a safety cable/chain onto your ceiling fan, you will need to run it through the download prior to installation.

Installing the Downrod:
Pass the motor power cord and safety cable through the download. (See Fig 4.1)
Note: Take out the end of the safety cable from the download before sliding the download into the plastic
head of the motor assembly.

Align the holes, secure with rod screws and washers in opposite directions from each other(2 sets on each side )and make sure the screws and washers are tightened firmly with a screwdriver Remove the screw already set inside of the motor shaft, then secure the safety cable into the motor shaft
firmly by this screw. (See Fig 4.2 & 4.3) Slide the wiring cover down until it rests on top of the motor assembly. (See Fig 4.4)

The downrod and canopy are assembled. (See Fig 4.5)

Installing the Mounting Bracket:
Install the mounting bracket to the ceiling box, as shown in Fig 5.1 below. Rotate the mounting bracket in different directions so that the bracket mounting holes match the screw holes of the ceiling box.

Note:

• This mounting bracket is a standard cable box. If the mounting bracket is installed at the outlet box, it should be installed on the outlet box with two screws matching the outlet box itself, as shown in Fig 5.1

• DO NOT use plastic outlet box. Use only U.L. listed outlet boxes marked”Acceptable for Fan
  Support of 15.9 kg (35 Ibs)or less”. This bracket can also be mounted to the wooden ceiling beam, and then the four ST5x24 screws can be used to lock the corresponding holes on the left and right sides of the bracket.

• The wooden ceiling beam must meet the tensile test of 30KG for installation, as shown in Fig 5.2.
  It is also possible to install the mounting bracket directly to the concrete ceiling and install four screws (not included) to the left and right corresponding holes of the bracket to lock the ceiling.

If you have an angled or vaulted ceiling: (Fig 5.3)

1. When installing the mounting bracket, the bracket groove is upward.
2. You will need a longer downrod.
3. lf your ceiling angle is greater than 27, you will also need an Angled Mounting Kit.

Hanging Ceiling Fan & Installing Power Adapter & Wiring the fan:

• WARNING: To reduce the risk of fire, electric shock or another personal injury, mount the fan only to an outlet box or supporting system marked acceptable for fan support and use the mounting screws provided with the outlet box.

• WARNING: Check to see that all connections are tight, including ground, and there are no VIsible bare wires at the wire nuts (except tor the ground wire).

• WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.

• WARNING: To avoid any electrical shock, be sure electricity is turned off at the main fuse
  box before wiring Install the ball end of the download into the opening of the mounting bracket. Rotate the download until the tab in the mounting bracket is seated in the slot in the downrod ball as shown in the enlarged image of Fig 6.1. Attach the safety cable/chain to a ceiling joist or to a metal brace mounted to two ceiling joists, or a sate place.

• WARNING: The fan and/or download should not rotate in the mounting bracket if installed correctly. Failure to align the slot in the downrod ball with the tab on the mounting bracket may result in fan falling causing serious injury or death.
  Slide the Adapter inside the bracket and connect the DC output wire connector molex from the adapter with the wire connector molex from the motor through the download as shown in Fig 6.3. Make sure all wires are tucked in the canopy. Connect the input wires of the adapter to the supply wires.

• Important: After the connections have been made, the connected wires should be turned upward and pushed carefully up into the outlet box.

• Warning: Slide the adapter horizontally into the bracket in the direction of the arrow shown in Fig 6.2 below, and the flat side facing the ceiling. Note that the upper patterns of the mounting bracket correspond to the two sides of the adapter’s push-in.

• Note: DO NOT stand upright (as shown in Fig 6.4) or place the adapter incorrectly (as shown in Fig 6.5), otherwise the adapter cannot be inserted into the bracket, which will affect the wiring.

• Note: The Green/Yellow wire from bracket connects with the supply Ground wire using the wire nut. Connect the White wire of the Adapter to the supply White (Neutral) wire using a wire nut, connect the Black wire of the Adapter to the supply Black (Hot/Live) wire using a wire nut. Then hide them inside the ceiling. (Make sure all the wires are connected to the correct colors as shown in Fig 6.3 )

Installing the Canopy:

There are two kinds of canopies and two ways to install. You may receive one of them. Please follow the below instructions before installation.

• A: The screws of mounting bracket are exposed.
  Make sure all wires are tucked in the canopy. Raise the canopy to the mounting bracket, align the hole slots in the canopy with the two mouting bracket screws, then turn the canopy in the direction of the arrow in Fig A until the mounting brackets screws engage from the bigger slots of the canopy to the smaller ones. Then secure the canopy to the mounting bracket with the screws.

• B: The screws of mounting bracket are not exposed.
  Make sure all wires are tucked in the canopy. Raise the canopy to the mounting bracket, align the two screws into the slot inside the canopy, rotate and twist the canopy to lock into place according to the direction of svmballarrow

Installing the Lampshade: Confirm the LED light wire molex connecting with the light board block terminal, and fix the lampshade into the light kit pan by rotating clockwise. Warning: To prevent SERIOUS INJURY or DEATH, make sure that lampshade is properly secured. Allow the lampshade to cool completely before removing.

Power on:
The Fig 9.1 below is a schematic diagram of the whole machine after installation. At this time, the ceiling fan has been installed. Turn on the power supply of the main switch or the room where the ceiling fan is installed. After power on, observe whether the fan light is on.

Remote Control Operating Instructions:

Pairing the Remote Control to Your Fan Within 1 min. of plugging fan to power source, press and hold the button for 3 sec. to pair remote
control and fan. Successful pairing will trigger the fan lamp off.

Remote Control button definitions

• Turns the fan off.

• Switches between summer mode and winter mode.

  • Summer mode – (Counter-clockwise) A downward airflow creates a cooling effect.
  • Winter model – (Clockwise) An upward airflow moves warm air away from the ceiling area and redistributes it around the living space.

• Turns the fan on and decreases fan speed.

• Turns the fan on and Increases fan speed

• Nature Switches the fan speed between nature mode and normal mode. Simulates a natural breeze,gentle enough not to disturb while you sleep.

• Turns the lights on or off and RF pairing.
  Note Press/hold button for 3 sec. within 1 min. of plugging fan to power source to pair remote and fan. The successful pairing will trigger the fan lamp of.

• Switches between warm light and cool light. WIFI Troubleshooting.
  Note: Press/hold the button for 5 sec. The fan will switch to AP Mode, then select AP Mode on APP, follow the APP control instructions and enable fan Wi-Fi.

• Press/Hold button to decrease the light intensity.

• Press/Hold to button to increase the light intensity.

APP Control Connection:

1. First download the free Carro Home app from the App Store or Google Play or scan the QR Code
   as below.
   Note: This ceiling fan needs to use 2.4Ghz wifi to work when you connecting the device, and after
   connecting it can use the 5Ghz or 2.4Ghz.

2. Open the Carro Home app to create your account. The account with “Carro Home” can be registered through E-mail or Mobile phone.
   Connect the device to the Carro Home app (Four ways connection):
   O Bluetooth connect (WIFI & Bluetooth on)

   • a. Press “+” button into the device list, then a window will pop up to show you some devices can be connected.

   • b. Click “Go to add” (If you click “Do not add” in mistake, please see “Do not add” steps).

   • C. Choose the device.

   • d. Connect to your home WIFI, then back to the app and wait for connecting.
     “Do not add” steps:

   • a. Select “Electrical'(smart switch) or “Air Circulation”(smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.

   • b. Connect to your home WIFl and tap “Next” to wait for connecting.

3. Auto Scan (WIFI & Bluetooth on)

   • a. Press “+” button into the device list.

   • b. Tap “Auto Scan” on the top.

   • C. Wait for the device comes out and tap “Next.

   • d. Press “+” button to add a device.

   • e. Connect to your home WIFI.

   • f. Wait for connecting.

   • O WIFl connect-EZ Mode (WIFl on & Bluetooth off)

   • a. Press “+” button to select “Electrical”(smart switch) or “Air Circulation”(smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.

   • b. Connect to your home WIFI (Only for 2.4 Ghz).

   • c. EZ Mode is set as default, just tap “Next” button to wait for the connection to complete. WIFI connect-AP Mode (WIFI on & Bluetooth off)

   • a. Smart ceiling fan: Press and hold the wIFI button on the remote for 5 seconds into AP Mode.
     Smart switch: Press and hold the “OFF” button for 10 seconds till the indicator light blinking slowly to into AP Mode.

   • b. Press “+” button to select “Electrical”‘(smart switch) or “Air Circulation”(smart ceiling fan) on the sidebar menu then select “Ceiling Fan Switch” or “Ceiling Fan” and tap next.

   • c. Connect to your home WIFI (Only for 2.4Ghz).

   • d. Choose AP Mode.

   • e. Press “Next button to go to connect the fan’s WIFI signal.

   • f.Choose the fan’s WIFl signal “CarroHome-XXXX” then back to the app.

   • g.Wait for connecting.
     Connect the device to Alexa:

   • a. Make sure you have connected the device to the app and working normally.

   • b. Open the Alexa app. go to the skill to search “Carro Home” skill.

   • c. Link the skill, log in with your Carro Home app account and password, then authorize and
     connect with the Carro Home app.

   • d. Then Alexa will find out the device automatically.

4. Connect the device to Google Home

   • a. Make sure you have connected the device to the app and working normally.
   • b. Open the Google Home app, Set up a device, choose “Works with Google”.
   • c. Search”Carro Home”, log in with your Carro Home app account and password., then authorize and connect with Carro Home app.
   • d. Then the Google Assistant will find out the device automatically.

5. Connect the device to Google Home
   a. Make sure you have connected the device to the app and working normally.
   b. Open the Google Home app. Set up a device, and choose “Works with Google”.
   c. Search”Carro Home”, log in with your Carro Home app account and password, then authorize
   and connect with Carro Home app.
   d. Then the Google Assistant will find out the device automatically.

6. Connect the device to the Siri shortcuts
   a. Make sure you have connected the device to the app and working in functional.
   b. Tap “Smart” on the main menu.
   c. Tap+” button.
   d. Tap “launch Tap To Run”
   e. Tap “Run the device”.
   f. Choose the device you want to control by Siri.
   g. Select the function you want to control by Siri.
   h. Then save it.
   J Add to Siri, choose the scene you just made, Add to Siri.

Basic product parameters:

Care and cleaning:

1. Check the support connections, brackets, and airfoil attachments twice a year. Make sure they are secure. Because of the fan’s natural movement, some connections may become loose over time. Itis not necessary to remove the fan from the ceiling.

2. Clean your fan periodically. Use only a soft brush or lint-free cloth to avoid scratching the finish
   The plating is sealed with a lacquer to minimize discoloration or tarnishing.

3. (Optional) Apply a light coat of furniture polish to the wood blades.

4. (Optional) Cover small scratches with a light application of shoe polish.
   Do not:

5. Use water when cleaning. Water could damage the motor, or the wood, or possibly cause an electrical shock.

6. Apply oil to your fan or motor. The motor has permanently lubricated sealed ball bearings.
   Note: Power off the fan before product maintenance or cleaning the fan.

Troubleshooting:

Try these troubleshooting steps before contacting Customer Service. For additional operation, maintenance,and troubleshooting information, please contact our customer service center.

FCC Statement:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of theNfollowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Carro USA Inc.
1431 S.Baker Ave. Ontario CA 91761
Tel: 888-253-2374
www.carrohome.com | cs@carrohome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>