ELDOM INVEST RH15NW Electric Panel Convector 1500W with Wi-Fi Control User Guide

RH15NW Electric Panel Convector 1500W with Wi-Fi Control
User Guide

RH15NW Electric Panel Convector 1500W with Wi-Fi Control

GUIDE FOR CONNECTING AN ELECTRONIC THERMOSTAT (ELECTRONIC CONTROL BOARD) WITH WIFI MODULE AND THE INTERNET SYSTEM FOR REMOTE CONTROL AND MONITORING MY SELDOM

WARNING! This guide is an integral part of the manual where working with the electronic thermostat (electronic control board) is described.
Connecting is optional and is not obligatory for the normal operation of the appliance!

CONNECTING THE WIFI MODULE TO THE INTERNET

The terms used in this guide are:

• module” – The WiFi module of the electronic thermostat (electronic control board) of the appliance.
• regulator” – the electronic thermostat (electronic control board) of the appliance.
• device” – smartphone, tablet, or laptop that is used to connect the WiFi module to the Internet and for its subsequent management and monitoring.
• WiFi network” – wireless network (WiFi) created from the module.
• internet network” – the desired wireless network you want to connect the module to. It is created by a router/modem, must be connected to the Internet, and should be located near the location where the appliance is located.
• system” – Internet-based remote management and monitoring system My Eldon.

ATTENTION! The built-in module is controlled by the regulator!
ATTENTION! Connecting the module to the Internet is necessary to enable the appliance to be controlled and to monitor its operation remotely!
ATTENTION! To connect the module to the Internet and to remotely control and monitor the operation of the appliance, a device is required on which the application My Eldon should be installed from Google Play or App Store, or use the QR codes at the end of this book.
ATTENTION! To connect the module to the system, the module must be connected to an Internet network, and the router/modem that creates this network must have a 32006 TCP packet output port enabled.
ATTENTION! The module can only be connected to an internet network that has letters, numbers, an “underscore” or a “dash” symbol in its name. No other characters, such as spaces, are allowed!
ATTENTION! If the internet network has WEP encoding, the password will need to be entered using the appropriate hexadecimal number representing each letter.
ATTENTION! If you enter the wrong password or name when connecting to the internet network, you may need to enter them right two times in a row in order to connect the module to the Internet. Before each entry, you must create a WiFi network by the module.
Connecting the module to the Internet takes place in 3 main steps. Subsequent remote control and monitoring of the appliance work is made through the system.

STEP 1. CREATE A WIFI NETWORK FROM THE MODULE

1. Enter the “New WiFi Net.” menu and turn the module into a model using the (OK) button.
   The name of the created WiFi network from the module, in the illustration above, is: NAT-AP-XXX

STEP 2. CONNECT THE DEVICE TO THE MODULE

1. Disconnect the device from the Internet:
   If your device (smartphone or tablet) has “mobile data” turned on, turn it off.
   If the device is a computer/laptop and its Internet connection is via a cable or mobile device – disconnect (remove) them.

2. Activate the GPS device location service.

3. Enable the WiFi module of the device, and connect it to the WiFi network created from the module.
   If the device does not find the WiFi network created from the module, repeat step 1 or restart the device’s WiFi module (turn it off and then turn it on again).
   If your device asks if you want to stay connected to the WiFi network created by the module, even though it is not connected to the Internet – stay connected.

STEP 3. CONNECT THE MODULE TO THE INTERNET USING THE DEVICE

1 Launch the app and fill in the fields in the Settings tab.
If a message appears “Application connected to the modem!”, Click OK.

• Field WiFi Network: the name of the internet network.
• Field Password: the password of the internet network.
• Field AccessCode: the access code to the module – last 4 symbols from the ID field of the additional information display regarding WiFi connections of the regulator.
• Field Security: the type of encoding of the internet network.
• Field Nearby Networks: the Internet networks found by the module. connection

NOTE In the drop-down menu of the Nearby Networks box, the internet networks found by the module are listed. The dropdown menu unfolds by clicking on it. The signal level (Signal) received by the module is also displayed for each of the listed internet networks. Because the levels are negative, the smaller number means that the signal is better. The module can work well with a signal with a number below 70. Signal levels above -80dBm are not recommended for use. In this case, move the router/modem of the internet network closer to the appliance or plug in an additional router or amplifier.
If the internet network is in the drop-down list of Nearby Networks and you select it, its log-in data (without its password in the Password field and the access code in the Access Code field) is filled in automatically. The password in the Password field and the access code in the Access Code field must be entered manually. If you connected the appliance to the internet network before, the password is filled in automatically (there may be no indication in the Password field).
If the module does not find the desired internet network or the network is hidden for it, you will need to enter the data in the fields.
2 .Click SEND

Depending on entered data in the fields, the following messages may be displayed:

• pplication connected to modem – the device and the module are connected

• Information is sent to modem – The information is sent to the module

• Incorrect access code – Wrong access code of the module

• Network connection is reset!.

• The application cannot connect to the device’s modem. Please reconnect to the device access point and try again! – the device can not connect to the module. Please reconnect the device to the module WiFi network again and try again.

• Network set successfully
  If the fields are filled in correctly:

• Within a few seconds, the WiFi network created from the module will shut down and the device connected to it will be able to connect to another network (by default) or stay not connected to a network.

• The symbol for Internet connection D will appear on the regulator display. This means that you have successfully connected the module to the Internet! Go to the next chapter.

ADDING THE CONNECTION TO THE INTERNET WIFI MODULE IN THE REMOTE CONTROL AND MONITORING SYSTEM MY ELDOM
Once you have connected the module to the Internet (you must see the Internet connection icon D on the regulator display)

1. Login – type: myeldom.com into the device’s browser address field or use the downloaded application. E-mail and password are used for login into the system.
   NOTE Forgotten password can restore it by clicking “Forgotten Password”
   Register a new user. If you are not registered for the system, you must do so – click “Register as a new user”, fill in the fields, and activate your account (profile) from the message you will receive at the e-mail you entered upon registration.

2. Once you have logged in, add the connection to the internet module using the,,+” button.
   It is necessary to enter the identifier (ID) of the appliance module and press the “Add” button.
   NOTE One module can only be added to one account.
   NOTE If you want to add a module that is added to another account, a message will appear: Device is already added by another user! You must remove it by “Remove” or share it through “Grant access” from the other account.
   NOTE You can control and/or monitor the appliance operation remotely via its Internet-connected module only from the account that it is added to. If for some reason you do not know which this account is, you should control and/or monitor the operation of the appliance in the conventional manner described in the instructions booklet for installation and use (which is an integral part of this guide).

3. Once you add the module you can remotely control the appliance and monitor its work.
   Detailed help instructions for operating with the system will be found after logging in with your account – button “?”

EU DECLARATION OF CONFORMITY

Hereby, Eldominvest Ltd. declares that the Electric convector with electronic control and Wi-Fi module is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: https://eldominvest.com/en/EU-declaration- RHW.html 

myeldom.com

|
---|---
https://play.google.com/store/apps/details?id=com.eldom.smarthome| https://itunes.apple.com/us/app/eldom-smart- home/id1350098710?ls=1&mt=8

Questions when connecting the module to the Internet or when working with the application:
Online video guides

|
---|---
https://youtu.be/o8zrbOylXv0| https://youtu.be/EoZjebnvxFg

Tel. +35952 504 506

Documents / Resources

| ELDOM INVEST RH15NW Electric Panel Convector 1500W with Wi-Fi Control [pdf] User Guide
RH15NW, Electric Panel Convector 1500W with Wi-Fi Control, RH15NW Electric Panel Convector 1500W with Wi-Fi Control
---|---

References

• My Eldom
• Declaration convectors RHW | Eldominvest Ltd.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>