serenelife SLCATL420 Gravity Flush Toilet High Profile User Guide

: June 5, 2024
: serenelife

Table of Contents

MAIN FEATURES
COMPONENTS
PRODUCT AND MOUNTING DIMENSION
INSTALLATION
OPERATION
FLUSH VALVE/SEAL CLEANING
WINTERIZATION AND STORAGE
FEATURES:
WHAT’S IN THE BOX:
TECHNICAL SPECS:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**User Guide

SICAR420 Gravity Flush Toilet High Profile with Foot Pedal Operation, T-Type Water Outlets**

MAIN FEATURES

Premium user comfort: Full size & soft-close seat and lid, large toilet bowl, and 478mm seat height brings greater home-like performance.
Easy to flush: High gloss toilet bowl with original
Type 3-way flush flow creates high-speed, full bowl flushing.
Ergonomically enhanced pedal operation: Lower pedal height for easier use.
One-direction action to open drain valve and flush.
Easy installation: Two bolts design flts most existing toilet floor flanges, great for new or replacement installation. Just place on floor flange, tighten bolts, connect water, and it’s ready.

COMPONENTS

PRODUCT AND MOUNTING DIMENSION

Ref.	Description
A	390mm / 15.4″
B	500mm / 19.7″ .
C	233mm / 9.2″
D	485mm / 19.1″
E	380mm / 15.0″
F	890mm / 35.0″
G	Minimum: 200mm / 7.9″
---	---
H	Minimum: 200mm / 7.9″
I	Minimum: 200mm / 7.9″
J	170mm / 6.7″
K	102mm / 4.0″
L	210mm / 8.5″

The outside diameter of the toilet drain outlet: 95mm / 3.7”;
The inner diameter of the toilet drain outlet: 87mm / 3.4”

INSTALLATION

Note:

Be sure foot pedal, when pressed, touches the same flat surface on which the toilet is installed.
Ensure water supply pressure is no more than 0.4Mpa.
Hot water more than 40 degrees is forbidden.

To replace an older toilet, turn off the water supply to the toilet. Remove and drain the water supply line.
Remove toilet hold-down bolts/screws. Remove the toilet from the floor. Remove and discard old flange seal and hold-down bolts. Verify center of the floor flange is at least 200mm/7.9” from the back wall (Fig.1).
If installing a new floor flange, make certain that toilet mounting holes are located at the correct angle (Fig.1). Floor flange must be secured to the floor with a minimum of four screws. Insert two supplied T-bolts into slots in the floor flange (Fig.2).
Verify that the floor flange seal is installed on the base of the toilet. Carefully set toilet over floor flange. Align holes in toilet base with T-bolts as toilet is lowered onto floor flange.
Install floor mounting nuts onto T-bolts. When tight, base should be securely attached and flat against the floor. Attach bolt covers onto nuts
Connect the water supply line to ½ inch water inlet and turn on the water supply line. (Fig.3) Flush the toilet several times and check for leaks.

|
---|---

Before connecting your pipe connector (plastic one is recommended) to the ½-inch water inlet (1/4-20 British thread), make sure there is a sealing ring in the pipe connector.
If not, the attached sealing ring must be placed to ensure perfect sealing. After connecting the water supply, flush the toilet several times to check leaks.

OPERATION

Add water to the bowl
To add water to the toilet, press the flush pedal part way down. Water flows into the bowl while the flush valve remains closed. If the flush valve moves, let up on the pedal slightly. Adding water to an empty bowl helps prevent holding tank odors from entering the living space. Adding water is recommended prior to flushing solids and toilet paper. (Fig.4)
Flush toilet
To flush, press the pedal down until it contacts the floor.
Release pedal after complete flush. (Fig.5) When flushing liquids, press the pedal for 1-2 seconds. When flushing solids, press pedal until contents are rinsed from the bowl.
Flushing longer than necessary will cause the holding tank to fall too quickly. A small amount of water will collect in the bowl after a flush t create an airtight seal.

FLUSH VALVE/SEAL CLEANING

After a period of time, mineral deposits from hard water may build up on the flush ball or seal, resulting in a slow water leak. To prevent this, periodically clean the flush valve and seal.

Remove minor debris from the flush valve and seal by slowly pressing and releasing the flush pedal several times. This will loosen and rinse debris from the surfaces.
Repeat several time for stubborn buildup (use a soft bristle brush if necessary).
Lubricate the flush valve and seal periodically with silicone spray or paste lubricant.

WINTERIZATION AND STORAGE

This toilet is not intended for use when exposed to temperatures below freezing.
Before storing the toilet, you need to drain water from the toilet according to the following procedures.

Turn off the water supply to the toilet.
Remove the water supply line from the water inlet.
Place a small container under the inlet to catch draining water.
Press the flush pedal and allow water to completely drain from the water inlet.
Leave the water line disconnected until the threat of freezing temperature is passed.

FEATURES:

Efficient Foot Pedal Operation
Home-like Comfort: Ergonomic Toilet Seat
Water-Saving T-type Water Outlet for Full-bowl Flush Coverage
Compact Design and Comfortable to Seat
Easy to Install
High-Gloss Surface
Easy to Clean
Odorless Sealing Design
Made from HDPE and PP Materials
2 Humanized Grooves of RV Toilet Low Proflle Foot Pedal to help Open and Close Easily
Distance from the Center of the Bolt Holes to the Back Wall is about 7.90” -inches