DIMPLEX SIL72 Sierra 72-In Wall Mount Electric Fireplace Owner’s Manual
- June 5, 2024
- Dimplex
Table of Contents
DIMPLEX SIL72 Sierra 72-In Wall Mount Electric Fireplace Owner’s Manual
We value your feedback!
Your input helps to create even better products and experiences.
Share the warmth and leave a review. dimplex.com/sharethewarmth
CONSUMER SAFETY INFORMATION: PLEASE READ THIS MANUAL BEFORE INSTALLING AND OPERATING THIS APPLIANCE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN A POSSIBLE ELECTRIC SHOCK, FIRE HAZARD, AND/OR INJURY AND WILL VOID THE WARRANTY.
To view the full line of Dimplex products, visit www.dimplex.com
Conventions used in this manual:
NOTE: Procedures and techniques considered important enough to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
WARNING: Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death.
Welcome
Please use our convenient online registration page to record your model and
serial
numbers for future reference at:
www.dimplex.com/register
CAUTION: Read all instructions and warnings carefully before starting
installation.
Failure to follow these instructions may result in a possible electric shock
or fire hazard and will void the warranty.
NO NEED TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information? Product Under Manufacturer’s Warranty?
Contact us at:
www.dimplex.com/customer_support
For Troubleshooting and Technical Support OR Toll-Free
1-888-346-7539
In order to better serve you, please have your model and serial numbers ready or register your product online before calling (see above)
IMPORTANT INSTRUCTIONS
Read this manual before attempting to install or use the electric fireplace.
Always comply with the warnings and safety instructions contained in this
manual to prevent personal injury or property damage.
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons, including
the
following:
-
This appliance is hot when in use. To avoid burns, do not let skin touch hot
surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 ft. from the front of this appliance and keep away from sides and rear. -
Extreme caution is necessary when any heater is used by, or near, children or invalids, and whenever the heater is left operating and unattended.
-
Do not operate any heater with a damaged cord or plug, after the
appliance malfunctions, or if it has been dropped or damaged in any manner. Disconnect from power and call Technical Service or have it inspected by a qualified electrician. -
To disconnect the fireplace, turn the controls off, then remove the plug from the outlet.
-
Do not use outdoors.
-
Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock, fire, or damage the fireplace. -
All electrical heaters have hot, and arcing, or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored.
-
Use this appliance only as described in the manual. Any other use not
recommended by the manufacturer may cause fire, electric shock or injury to persons. -
If possible, always unplug this appliance when not in use.
-
Any repairs to this fireplace should be carried out by a qualified service person.
-
Under no circumstances should this fireplace be modified. Parts that have to be removed for servicing must be replaced prior to operating this fireplace again.
-
This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never place the heater where it may fall into a bathtub or other water containers.
-
Always connect to properly grounded outlets.
-
Do not run cord under carpeting.
Do not cover cord with throw rugs, runners or the like. Arrange the cord away from heavily trafficked areas, where it will not be tripped over. -
Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or a relocatable power tap (outlet/power strip).
-
To prevent a possible fire, do not block air intakes or exhaust in any manner.
Do not use on soft surfaces, like bed, where opening may become blocked. -
There is a resettable cutout switch inside the heater. Should the heater overheat, the cutout will turn the fireplace heater off. To reset the cutout switch unplug the unit and wait 5 minutes before plugging it back in.
Caution: If you need to continuously reset the cutout, unplug the unit and call Technical Support. -
Remote control contains a small battery. Keep away from children. If swallowed, seek medical attention immediately
FCC Compliance
CAUTION: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try and correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between theequipment and the receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/ TV technician for help
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment. This Class B digital apparatus complies with Canadian ICES-003.
CAUTION
- RISK OF ELECTRIC SHOCK
- DO NOT OPEN
- NO USER-SERVICEABLE PARTS INSID
Specifications
Electrical
- Voltage: 120VAC 60Hz
- Watts: 1400 Watts
- Amps: 12 A
- Wiring: Plug-In
- Bulb Type: LED
Approvals :
Dimensions
SIL48/SIL48M
- Width: 41-1/4″ (104.6 cm)
- Height: 18-1/8″ (46.0 cm)
- Height with feet: 21-1/2″ (54.7 cm)
- Depth: 5-1/4″ (13.3 cm)
- Depth with feet: 11″ (27.9 cm)
Weight
- 40.8 lbs (18.5 kg)
SIL60/SIL60M
- Width: 51-7/8″ (131.8 cm)
- Height: 18-1/8″ (46.0 cm)
- Height with feet: 21-1/2″ (54.7 cm)
- Depth: 5-1/4″ (13.3 cm)
- Depth with feet: 11″ (27.9 cm)
Weight
- 63.5 lbs (28.9 kg)
SIL72
- Width: 64″ (162.6 cm)
- Height: 18-1/8″ (46.0 cm)
- Height with feet: 21-1/2″ (54.7 cm)
- Depth: 5-1/4″ (13.3 cm)
- Depth with feet: 11″ (27.9 cm)
Weight
77.8 lbs (35.3 kg)
SIL96
- Width: 96″ (243.4 cm)
- Height: 18-1/8″ (46.0 cm)
- Height with feet: 21-1/2″ (54.7 cm)
- Depth: 5-1/4″ (13.3 cm)
- Depth with feet: 11″ (27.9 cm)
Weight
- 105.8 lbs (48 kg)
Package Contents
Installation
GROUNDING INSTRUCTIONS
- This product is equipped with a cord that has an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
- This heater is for use on 120 volts. The cord has a plug as shown.
- A 15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred, but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or the fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.
WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock, or injury to persons.
IN-WALL INSTALLATION
Cabinet – in / cm
Model | A | B | C |
---|---|---|---|
Sierra 48 – SIL48 | 41.6 / 105.7 | 6.5 / 16.5 | 18.5 / 47.0 |
Sierra 60 – SIL60 | 52.4 / 133.1 | 6.5 / 16.5 | 18.5 / 47.0 |
Sierra 72 – SIL72 | 64.4 / 163.6 | 6.5 / 16.5 | 18.5 / 47.0 |
Sierra 96 – SIL96 | 88.4 / 224.5 | 6.5 / 16.5 | 18.5 / 47.0 |
Firebox – in / cm
Model | D | E | F |
---|---|---|---|
Sierra 48 – SIL48 | 41.2 / 104.6 | 4.7 / 11.9 | 18.1 / 46.0 |
Sierra 60 – SIL60 | 51.9 / 131.8 | 4.7 / 11.9 | 18.1 / 46.0 |
Sierra 72 – SIL72 | 64.0 / 162.6 | 4.7 / 11.9 | 18.1 / 46.0 |
Sierra 96 – SIL96 | 88.0 / 223.5 | 4.7 / 11.9 | 18.1 / 46.0 |
IN-WALL INSTALLATION
ON-WALL INSTALLATION
Dimensions – in / cm
Model | A | B |
---|---|---|
Sierra 48 – SIL48 | 16 / 40.6 | 7.9 / 20 |
Sierra 60 – SIL60 | 32 / 81.3 | 7.9 / 20 |
Sierra 72 – SIL72 | 32 / 81.3 | 7.9 / 20 |
Sierra 96 – SIL96 | 48 / 121.9 | 7.9 / 20 |
TABLE TOP INSTALLATION
Operation
The fireplace can be operated with the multi–function IR remote control or from the touchscreen controls on the top-right of the front glass.
Once the fireplace is turned on the digital display and the control icons on
the front
glass will illuminate. If no button or icon is pressed within 10 seconds, the
fireplace
controls will deactivate by the digital display turning off first and then the
icons. To
reactivate the controls press any button on the remote or touch any icon on
the front glass.
- Power ON/OFF
- Flame Control
- Heat ON/OFF
- Timer
- Ember Bed
- Level Selection
- Digital Display
Remote
NOTE: The heater on your fireplace may emit a slight, harmless odor when
first used. This odor is a normal condition caused by initial heating of
internal heater
parts and will not occur again.
CUTOFF SWITCH
NOTE: There is a safety temperature cutoff switch (cutout) inside the heater. If the heater overheats, the cutout will shut off the supply power.
It can be reset by unplugging the unit and waiting 5 minutes before plugging
the
unit back on.
CAUTION: If you need to continuously reset the heater, unplug the unit
and call
technical service at 1-888-346-7539
POWER ON/OFF
The ON/OFF button turns the fireplace ON and OFF. When the fireplace is OFF,
pressing the ON/OFF button on the remote control or touching the icon on the
front glass will turn on the fireplace. If the ON/OFF button is pressed again
within 10 seconds it will turn OFF the fireplace. With inactive controls,
press twice to turn OFF the fireplace. The first press on the ON/OFF button
lights up the touchscreen icons and activates the controls.
The fireplace has a built-in memory function. When the fireplace is turned
back
on, the display will show the last selected function and it will start at the
last used
settings (except timer). If the fireplace is disconnected from the main power
source,
it will restart at the default settings.
FLAME CONTROL
This button is used to turn flames ON, to alter the flame color and to turn
flames
OFF. Press the Flame button multiple times to cycle through 7 solid color
options
(L8, L7, L6, L5, L4, L3, L2), color rotation option (L1) and flames OFF.
While L8, L7…or L2 is displayed, press the Level Selection button to change
the
brightness of the flames from the available options: 3- High, 2-Medium and
1-Low.
HEAT ON/OFF
Pressing the Heat control turns the heater on and off.
With Heat ON and set temperature displayed, press the Level Selection button multiple times to cycle through the 11 temperature settings: 72°F, 74°F, 76°F, 78°F, 80°F, 82°F, ON, 64°F, 66°F, 68°F, 70°F, (22°C, 23°C, 24°C, 25°C, 26°C, 27°C, ON, 18°C, 19°C, 20°C, 21°C).
‘ON’ means the heater operates continuously.
Changing the temperature unit (°F↔°C):
With Heat ON and display showing the set temperature, press and hold the ON/
OFF icon on the touchscreen for 5 seconds. The display will flash 3 times and
it will switch from °F to °C or °C to °F.
! NOTE: This function cannot be set with the remote control.
Heater Enable & Disable Function:
From the touchscreen controls touch and hold the Heat icon for 10 seconds. The
ember bed will flash 6 times to indicate that the heater function is disabled.
When
the heat is disabled, pressing the Heat button will cause the ember bed to
flash, but
the heater will not operate.
To enable the heater again, touch and hold the Heat icon for 10 seconds.
! NOTE: This function cannot be set with the remote control.
TIMER CONTROL
The Timer button is used to activate or deactivate the sleep timer
Pressing the Timer turns the timer on and ‘8h’ appears on the display.
Pressing the
Timer a second time within 10 seconds will turn the timer off. To set the
time, use the Level Selection control to select the desired time from the
following: 8h-1h 2h3h-4h-5h-6h-7h.
The fireplace will shut off after the selected time period. Switching the fireplace OFF with the Power Button will clear any timer setting.
EMBER BED
The Ember Bed button changes the ember bed by cycling through the seven color
options: color rotation ‘d1’ and smoldering (fluctuating brightness) embers
option
‘d9’. With ‘d8’ through ‘d2’ displayed, the Level Selection button will adjust
the brightness of the ember bed from 3- High, 2-Medium, and 1-Low.
LEVEL SELECTION BUTTON
The Level Selection button is used to adjust the heat setting, as well flame and ember bed brightness and timer setting. See relevant section for more details.
Maintenance
- Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household cleaners as these products will damage the metal trim.
- The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/output vents is recommended.
The heater should be cleaned and inspected regularly, depending on conditions, and at least at yearly intervals.
WARNING: Any electrical repairs of this unit should be carried out by a
licensed
electrician in accordance with national and local codes.
WARNING: Disconnect power by unplugging the power and allowing heater to
cool before attempting any maintenance or cleaning to reduce the risk of fire,
electric shock, or injury.
NOTE: When the heater is not in use, the heater should be stored in a dry
location, away from possible damage. The power cord should be stored properly
to avoid contact with hot or sharp objects.
Remote Control
The battery compartment is located on the back end of the remote control.
- Press and slide the battery cover open.
- Insert two 1.5V (AAA) batteries (included) ensuring they are installed correctly with regard to the polarities (+ and -) marked on the inside of the battery compartment.
- Replace the battery cover.
! NOTE: The battery should be removed if the product is to be left unused
for a
long time.
Replacing the Remote Control Batteries
When replacing the batteries, replace both batteries at the same time with new batteries of the correct type.
- Do not mix old and new batteries.
- Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nicad, Nimh, etc) batteries.
Disposal of Used Batteries
Batteries may contain hazardous substances that could be endangering to environment and human health.
- This symbol marked on the battery and/or packaging indicates that used batteries shall not be treated as municipal waste. Instead they shall be left at the appropriate collection point for recycling.
- By ensuring the used batteries are properly disposed of, you will help prevent
potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources.
For more information about collection and recycling of used batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased this item.
Troubleshooting
Fault code | Fault Cause | Solution |
---|---|---|
E1 | The heater overheating | Call technical support. |
E2 | Thermistor is defective. | Call technical support. |
E3 | The heater not working. | If the vents are dirty or clogged. Unplug the |
power, clean the dust and debris of the vent area. Wait for 5 minutes, plug in and turn on the heater. If the heater still don’t work, please call technical support.
Technical Service
Contact our friendly customer service team for technical and trouble-shooting
support. Make sure you have your sales receipt, location of purchase, and the
model and serial number of your product.
1-888-346-7539 | www.dimplex.com/contact_us
Warranty
One Year Limited Warranty
Products to which this limited warranty applies
This limited warranty applies to your newly purchased Dimplex electric compact
insert. This limited warranty applies only to purchases made in any province
of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in
any of the 50 States of the USA (and the District of Columbia) except for
Hawaii and Alaska.
This limited warranty applies to the original purchaser of the product only
and is not transferable.
Products excluded from this limited warranty
Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner/purchaser. Products purchased in Yukon Territory, Nunavut, Northwest Territories, Hawaii, or Alaska are not covered by this limited warranty. Products purchased in these States, provinces, or territories are sold AS IS without warranty or condition of any kind (including, without limitation, any implied warranties or conditions of merchantability or fitness for a particular purpose) and the entire risk of as to the quality and performance of the products is with the purchaser, and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair.
What this limited warranty covers and for how long
Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Glen Dimplex Americas Ltd. (herein called Glen Dimplex Americas) warrants such products to be free from defects in material and workmanship for a period of 12 months from the date of the first purchase of such product.
The limited 12 month warranty period also applies to any implied warranties
that
may exist under applicable law. Some jurisdictions do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to
the purchaser.
What this limited warranty does not cover
This limited warranty does not apply to products that have been repaired
(except by Glen Dimplex Americas or its authorized service representatives) or
otherwise altered.
This limited warranty does further not apply to defects resulting from misuse,
abuse, accident, neglect, incorrect installation, improper maintenance or
handling, or operation with an incorrect power source.
What you must do to get service under this limited warranty
Defects must be brought to the attention of Technical Service at
1-888-346-7539.
Please have proof of purchase, catalogue/ model and serial numbers available
when calling. Limited warranty service requires a proof of purchase of the
product.
What Glen Dimplex Americas will do in the event of a defect
In the event a product or part covered by this limited warranty is proven to be defective in material or workmanship during the 12 month limited warranty period you have the following rights:
-
Glen Dimplex Americas will in its sole discretion either repair or replace such
defective product or part without charge. If Glen Dimplex Americas is unable to repair or replace such product or part, or if repair or replacement is not
commercially practicable or cannot be timely made, Glen Dimplex Americas may, in lieu of repair or replacement, choose to refund the purchase price for such product or part. -
Limited warranty service will be performed solely by dealers or service agents of Glen Dimplex Americas authorized to provide limited warranty services.
-
The purchaser is responsible for removal and transportation of such product or part (and any repaired or replacement product
or part) to and from the authorized dealer’s or service agent’s place of business. -
This limited warranty does not entitle the purchaser to on-site or in-home services. On-site or in-home services may be performed at the purchaser’s specific request and expense at Glen Dimplex Americas then-current rates for such services.
-
Glen Dimplex Americas will not be responsible for, and the limited warranty services shall not include, any expense incurred for installation or removal of the product or part (or any replacement product or part) or any labour or transportation costs. Such costs shall be the purchaser’s responsibility
How State and Provincial law apply
This limited warranty gives you specific legal rights, and you may also have
other rights which vary from jurisdiction to jurisdiction.
The provisions of the United Nations Convention on Contracts for the Sale of
Goods shall not apply to this limited warranty or the sale of products covered
by this limited warranty
What Glen Dimplex Americas and its dealers and service agents are also not responsible for:
IN NO EVENT WILL GLEN DIMPLEX AMERICAS, OR ITS DIRECTORS, OFFICERS, OR AGENTS,
BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY, WHETHER IN CONTRACT, IN TORT,
OR ON
ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY,
CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN
CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT
EVEN IF GLEN DIMPLEX AMERICAS OR ITS DIRECTORS, OFFICERS, OR AGENTS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH
LOSSES, COSTS, OR DAMAGES ARE FORESEEABLE. IN NO EVENT WILL GLEN DIMPLEX
AMERICAS, OR ITS OFFICERS, DIRECTORS, OR AGENTS BE LIABLE FOR ANY DIRECT
LOSSES, COSTS, OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO THE PURCHASER.
References
- Leave a review | Dimplex
- Electric Fireplace & Heating Solutions | Dimplex
- Heating Product Registration | Dimplex
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>