FASTCABLING 5540-55 60W 95W 2 Port Waterproof PoE Extender User Guide
- June 5, 2024
- FASTCABLING
Table of Contents
5540-55 60W 95W 2 Port Waterproof PoE Extender
User Guide
Before You Start
Thank you for choosing us. Fastcabling PoE extender is designed to repeat the power over Ethernet without breaking IEEE standards. According to the IEEE802.3 standard, the Power over Ethernet (PoE) distance is 100 meters maximum. A single PoE extender can repeat 100 meters. 4 units work together will repeat up to 400 meters. Please take a few minutes to read through this quick guide before you get started. There are helpful tips you may want to learn about.
What Should be Concerned Before Using PoE Extender?
Voltage drop is a critical factor for long-distance power transmission. If the voltage drops down to 38 VDC even lower at the front-end IP device, the whole PoE power system may stop working. What you will see is there’s no power to your IP camera or AP at all. The voltage drop is relative to both cable distance and the power consumption on IP device. The longer the distance plus the higher power consumption on the device, the more serious the voltage drop will be. For example, if there is 150 meters between the PoE switch and IP camera, either increasing the distance to 200 meters or adding more IP devices at the front end will create more voltage drop. The voltage drop will be converted into heat which is energy lost on the cable. Please refer the maximum distance chart below to see whether the solution can meet your system design requirement or not.
Pick the Ethernet Cable with Pure Copper
In the practical application, an unqualified Ethernet cable is the biggest issue increasing the voltage drop than it should be. You may be getting the cat5e with Copper Clad Aluminum. We recommend choosing the Pure Copper cat5e or higher grade cable, especially when your transmit distance is going to reach the limit (100 meters per unit). Pure copper cable not only can guarantee distance, but also transmission speed. If you see no power output on the PoE extender, please contact us support@golbong.com. We will get back to you shortly.
WATCH THE VIDEO
How to check cat5e Ethernet cable
Hardware Overview
| 
---|---
- Accept up to 90W IEEE802.3bt POE++ input
LED Indicators:
| LED | Color | Function |
|---|---|---|
| LAN | Green | Lights to indicate 100/1000mbps network is established. |
Blinks to indicate that both power and data are passing through.
Hardware Installation
-
Firstly Disassemble the cable gland as shown below:
-
Next, attach the gland body (with washer) to the PoE extender. Use a 27mm wrench to fasten the gland body tightly.
Important: Make sure the
gland body is squeezed tightly with a wrench, the PoE extender can’t pass IP67
waterproof test without using the wrench to fasten the gland body.
-
Slip the Ethernet cable through the clamping nut and the body of the sealing insert, and cut out the sealing insert if the RJ45 is pre-crimped.
-
Plug the Ethernet connector to the PoE input port.
-
Next Insert the sealing insert into the cable grand body and attach the clamping nut to complete the cable assembly. Now
Use a 27mm wrench again to fasten the crimping nut.
-
Repeat step 1 to step 5 for two PoE out ports.
-
Use a rubber plug to block one of the out ports if you need a single PoE port.
WATCH THE VIDEO
How to install IP67 outdoor PoE
Electrical Safety Information
- Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment, or pose a fire hazard if the limitations are not followed.
- There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
- The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.
- Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.
- Protective bonding must be installed in accordance with local national wiring rules and regulations.
Need More Help?
If you require more help setting up your outdoor PoE extender, please head to
our help site where you will be able to find the corresponding help guides and
video tourists.
Visit our help site
fastcabling.com/support/
Declaration of Conformity
We. Fastcabling LTD., hereby declares that the products:
Fastcabling 90W Outdoor PoE Extender
is in conformity with all the essential requirements of EMC Directive
2014/30/EU
Assessment of compliance of the product with the requirements relating to the
following specifications:
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
EN 55032:2015+AC:2016 Class A
AS/NZS CISPR 32:2015 Class A
EN 61000-3-2:2014 Class A EN 61000-3-3:2013 EN 55035:2017
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>