MAYTAG MVW4505MW 4.5 Cu. Ft. Top Load Washer Owner’s Manual

MAYTAG MVW4505MW 4.5 Cu. Ft. Top Load Washer

Your safety and the safety of others are very important

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

• DANGER You can be killed or seriously injured if you don’t immediately follow instructions.
• WARNING You can be killed or seriously injured if you don’t follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:

• Read all instructions before using the appliance.
• Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
• Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.
• Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
• If the hot-water system has not been used for such a period, before using a washing machine, turn on all hot-water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
• Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.
• Before the appliance is removed from service or discarded, remove the door.
• Do not reach into the appliance if the tub or agitator is moving.
• Do not install or store this appliance where it will be exposed to the weather.
• Do not tamper with controls. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.
• Do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).
• See the Installation Instructions for grounding requirements and installation.

SAVE THESE INSTRUCTIONS

WARNING
Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel – Do not contact the thermostat bracket while the appliance is energized

CHOOSING THE RIGHT DETERGENT

Use only High-Efficiency detergents. The package will be marked “HE” or “High Efficiency.” Low-water washing creates excessive sudsing with a non-HE detergent. Using non-HE detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component malfunction and, over time, buildup of mold or mildew. HE detergents should be low-sudsing and quick-dispersing to produce the right amount of suds for the best performance. They should hold soil in suspension so it is not redeposited onto clean clothes. Not all detergents labeled as High Efficiency are identical in formulation and their ability to reduce suds. For example, natural, organic, or homemade HE detergents may generate a high level of suds. Always follow the detergent manufacturer’s instructions to determine the amount of detergent to use. Do not go over the Max Line on the dispenser. See Quick Start Guide for more information.

WASHER MAINTENANCE AND CARE

Water Inlet Hoses
Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found. When replacing your inlet hoses:

• Mark the date of replacement on the label with a permanent marker.
• Check that the old washers are not stuck on the washer inlet valves.
• Use new washers in the new inlet hoses to ensure a proper seal.

NOTE: This washer may not include inlet hoses. See the Installation Instructions for more information.

Washer Care
Recommendations to help keep your washer clean and performing at its best

1. Always use High Efficiency (HE) detergents and follow the HE detergent manufacturer’s instructions regarding the amount of HE detergent to use. Never use more than the recommended amount because that may increase the rate at which detergent and soil residue accumulate inside your washer, which in turn may result in undesirable odor.
2. Use warm and hot wash water settings sometimes (not exclusively cold water washes), because they do a better job of controlling the rate at which soils and detergent accumulate.
3. Always leave the washer lid open between uses to help dry out the washer and prevent the buildup of odor-causing residue.

Cleaning your top-loading washer
Read these instructions completely before beginning the routine cleaning processes recommended below. This Washer Maintenance Procedure should be performed, at a minimum, once per month or every 30 wash cycles, whichever occurs sooner, to control the rate at which soils and detergent may otherwise accumulate in your washer.

Cleaning the inside of the washer
To keep your washer odor-free, follow the usage instructions provided above and use this recommended monthly cleaning procedure:
Recommended cycle for cleaning the asher Some models have a “Clean Washer” cycle that uses higher water volumes in combination with affresh® Washer Cleaner or liquid chlorine bleach to clean the inside of the washer. If your model does not have a “Clean Washer” cycle, refer to the online Cycle Guide for the optimal cycle for cleaning the inside of the washer. Use this cycle with affresh® Washer Cleaner or liquid chlorine bleach as described below.

Description of Clean Washer with affresh® cycle operation:

1. This cycle will fill to a washer level high than in normal wash cycles to provide rinsing than in normal wash cycles to provide rinsing at a level above the water line for normal wash.
2. During this cycle, there will be some agitation and spinning to increase the removal of soils. After this cycle is complete, leave the lid open to allow for better ventilation and drying of the washer interior.

Begin procedure

1. Affresh® washer cleaner cycle procedure (recommended for best performance):
   • a. Open the washer lid and remove any clothing or items.
   • b. Place an affresh® Washer Cleaner tablet in the bottom of the washer basket.
   • c. Do not place an affresh® Washer Cleaner tablet in the detergent dispenser.
   • d. Do not add any detergent or other chemical to the washer when following this procedure.
   • e. Close the washer lid.
   • f. Select the cycle recommended for cleaning the inside of the washer.
   • g. Press the Start button to start the cycle.

NOTE: For best results, do not interrupt the cycle. If cycle must be interrupted, press Power/Cancel. (For models with no Power/ Cancel button, press and hold Start/Pause for three seconds.) After the cycle has stopped, run a Rinse & Spin cycle to rinse the cleaner from the washer.

Chlorine bleach procedure (alternative):

• a. Open the washer lid and remove any clothing or items.

• b. Add 1 cup (236 mL) of liquid chlorine bleach to the bleach compartment.
  NOTE: Use of more liquid chlorine bleach than is recommended above could cause washer damage over time.

• c. Close the washer lid.

• d. Do not add any detergent or other chemical to the washer when following this procedure.

• e. Select the cycle recommended for cleaning the inside of the washer.

• f. Press the Start button to start the cycle.

NOTE: For best results, do not interrupt cycle. If the cycle must be interrupted, press Power/Cancel. (For models with no Power/ Cancel button, press and hold Start/Pause for three seconds.) After the cycle has stopped, run a Rinse & Spin cycle to rinse cleaner from the washer.

Cleaning the dispensers
After a period of using your washer, you may find some residue buildup in the washer’s dispensers.

IMPORTANT: Dispensers are not dishwasher-safe.

For non-removable dispensers: To remove residue from the dispensers, wipe them with an affresh® Machine Cleaning Wipe or a damp cloth and towel dry. Do not attempt to remove the dispensers or trim for cleaning. The dispensers and trim are not removable. For removable dispensers: If your model has a dispenser drawer, press tab(s) to remove the drawer and clean it with an affresh® Machine Cleaning Wipe or a damp cloth and towel dry before or after you run the Clean Washer cycle. Use an all-purpose surface cleaner, if needed. Cleaning the outside of the washer

IMPORTANT: To avoid damaging the washer’s finish, do not use abrasive products. Use an affresh® Machine Cleaning Wipe, a soft, damp cloth, or sponge to wipe away any spills. Use an affresh® Machine Cleaning Wipe or only mild soaps or cleaners when cleaning external washer surfaces.

Nonuse and Vacation Care

Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps:

1. Unplug or disconnect power to washer.
2. Turn off water supply to washer to avoid flooding due to water pressure surge.

Winter Storage Care

IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer.

To winterize washer:

1. Shut off both water faucets; disconnect and drain water inlet hoses.
2. Put 1 L (1 qt.) of R.V.-type antifreeze in basket and run washer on Rinse & Spin cycle for about 30 seconds to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.

Transporting Your Washer

1. Shut off both water faucets. Disconnect and drain water inlet hoses.
2. If washer will be moved during freezing weather, follow “Winter Storage Care” directions before moving.
3. Disconnect drain hose from drain system and drain any remaining water into a pan or bucket. Disconnect drain hose from back of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7.  Place original shipping materials back inside washer. If you do not have shipping materials, place heavy blankets or towels into basket opening. Close lid and place tape over lid and down front of washer. Keep lid taped until washer is placed in new location. Transport washer in the upright position.

Reinstalling/Using Washer Again

WARNING

Electrical Shock Hazard

• Plug into a grounded 3-prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

To reinstall washer after nonuse, vacation, winter storage, or moving:

1. Refer to Installation Instructions to locate, level, and connect washer.
2. Before using again, run washer through the following recommended procedure: To use washer again:
3.  Flush water pipes and hoses.
4. Reconnect water inlet hoses.
5. Turn on both water faucets.
6. Plug into a grounded 3 prong outlet or reconnect power.
7. See your online Cycle Guide for information about which cycle(s) to run your washer through to clean washer and remove antifreeze if used. Use only HE High-Efficiency detergent. Use half the manufacturer’s recommended amount for a medium-size load.

INSTALLATION INSTRUCTIONS REQUIREMENTS

Tools and Parts
Gather required tools and parts before starting installation.

Tools Needed:

Parts Supplied: NOTE: All parts supplied for installations are in the washer. Drain hose with clamp, U-form, and cable tie

Parts Needed: (if not supplied with washer)
NOTE: Various inlet hose options are available; check your Quick Start Guide for ordering information.

Alternate Parts: (not supplied with washer)
Your installation may require additional parts. To order, please refer to the contact information referenced in your Quick Start Guide.
If you have: You will need
Overhead sewer Standard 20 gal. (76 L) 39″ (990 mm) tall drain tub or utility sink, sump pump, and connectors (available from local plumbing suppliers)
1″ (25 mm) standpipe 2″ (51 mm) diameter to 1″ (25mm) diameter standpipe adapter and connector kit
Drain hose too short Extension drain hose and connector kit
Lint-clogged drain Drain protector and connector kit

Location Requirements

Select proper location for your washer to improve performance and minimize noise and possible “washer walk.” Install your washer in a basement, laundry room, closet, or recessed area.

IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32°F (0°C). Water remaining in washer after use may cause damage in low temperatures. See “Washer Maintenance and Care” for winterizing information. Proper installation is your responsibility.
You will need:

• A water heater set to 120°F (49°C).
• A grounded electrical outlet located within 4 ft. (1.2 m) of power cord on back of washer.
• Hot and cold water faucets located within 3 ft. (0.9 m) of hot and cold water fill valves on the washer, and water pressure of 20– 100 psi (138–690 kPa).
• A level floor with a maximum slope of 1″ (25 mm) under entire washer. Installing on carpet or surfaces with foam backing is not recommended.
• The floor must support the washer’s total weight (with water and load) of 315 lbs. (143 kgs).

Recessed area or closet installation

NOTE: All 27″ wide washers should have 19″ clearance, while all 29″ wide washers should have 22″ clearance.

All dimensions show recommended spacing allowed, except for closet door ventilation openings, which are the minimum required. This washer has been tested for installation with a spacing of 0″ (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Add spacing of 1″ (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required. *For additional details (or information) specific to your model, refer to your Quick Start Guide.

Drain System
A drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select the method you need.

IMPORTANT: To avoid siphoning, no more than 4.5″ (114 mm) of drain hose should be inside the standpipe or below the top of wash tub. Secure drain hose with cable tie.

Floor standpipe drain system

Minimum diameter for a standpipe drain: 2″ (51 mm). Minimum carry- away capacity: 17 gals. (64 L) per minute. The top of the standpipe must be at least 39″ (990 mm) high; install no higher than 96″ (2.44 m) from the bottom of the washer. If you must install higher than 96″ (2.44 m), you will need a sump pump system.

Wall standpipe drain system See requirements in the “Floor standpipe drain system” section.

Laundry tub drain System Minimum capacity: 20 gals. (76 L). The top of the laundry tub must be at least 39″ (990 mm) above the floor; install no higher than 96″ (2.44 m) from the bottom of the washer.

Floor Drain System
The floor drain system requires a Siphon Break Kit, 2 Connector Kits, and an Extension Drain Hose that may be purchased separately; refer to the Quick Start Guide for online ordering information. Minimum siphon break height: 28″ (710 mm) from the bottom of the washer (additional hoses may be needed).

Electrical Requirements

WARNING

Electrical Shock Hazard

• Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.
• A 120 V, 60 Hz, AC-only, 15 or 20 A, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this appliance be provided.
• This washer is equipped with a power supply cord having a 3-prong grounding plug.
• To minimize possible shock hazards, the cord must be plugged into a mating, 3-prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.
• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
• Do not ground to a gas pipe.
• Check with a qualified electrician if you are not sure the washer is properly grounded.
• Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected appliance: This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance: If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

For a permanently connected appliance: This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

SAVE THESE INSTRUCTIONS

INSTALLATION

Unpacking

WARNING

Excessive Weight Hazard: Use two or more people to move and install or uninstall appliances. Failure to do so can result in back or another injury. Before you start: remove shipping materials. It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from the washer.

1. Move Washer
   Move washer to within 4 ft. (1.2 m) of its final location; it must be in a fully upright position.
   NOTE: To avoid floor damage, set washer onto cardboard before moving it and make sure lid is taped shut

2. Remove shipping base
   IMPORTANT: Removing the shipping base is necessary for proper operation. If your washer includes a sound shield, please refer to the instructions included with the sound shield to install it at this time. To avoid damaging the floor, place cardboard supports from the shipping carton on the floor behind the washer. Tip washer back and place on cardboard supports. Remove shipping base (some models require the shipping base to be rotated 90° to the right before pulling off). Set washer upright.

3. Remove packaging material from the inside washer Remove tape from washer lid, open lid, and remove packaging material from washer tub. Be sure that all parts have been removed from the inside washer.
   NOTE: Keep packaging material inside the washer in case you need to move the washer later.

4. Free power cord

****Firmly grasps the power cord plug and pulls it free from the rear panel. Gently place the power cord over the console to allow free access to the back of the washer

Connect Drain Hose

Attach drain hose to drain port

• If applicable, remove the red plastic plug from the black drain port on the back of the washer.  If the clamp is not already in place on the elbow end of the drain hose, slide it over the end as shown. Squeeze clamp with pliers and slide black elbow end of drain hose onto black drain port and secure with clamp. For a laundry tub or standpipe drain, go to step 6. For a floor drain, remove the pre-installed drain hose form as shown in step
• You may need additional parts with separate directions. See the “Alternate Parts” section.

Place drain hose in a standpipe IMPORTANT: 4.5″ (114 mm) of drain hose should be inside the standpipe; do not force excess hose into a standpipe or lay it on the bottom of the laundry tub. A drain hose form must be used. Place hose into standpipe (shown in picture) or over the side of the laundry tub.

Remove drain hose form (floor drain installations only)

• For floor drain installations, you will need to remove the drain hose form from the end of the drain hose. You may need additional parts with separate directions. See “Tools and Parts.” It is the responsibility of the installer to install and secure the drain hose into the provided plumbing/drain in a manner that will avoid the drain hose coming out of and leaking from the plumbing/drain.

Connect Inlet Hoses

The washer must be connected to water faucets with new inlet hoses with flat washers (not provided). Do not use old hoses.
NOTE: Both hoses must be attached and have water flowing to inlet valves. If you are only connecting to a cold water faucet, you must use a Y-adapter (not provided).

Connect inlet hoses to water faucets IMPORTANT: Do not overtighten the hose or use tape or sealants on valve. Damage to the valves can result. Attach hose to hot water faucet. Screw on the coupling by hand until it is seated on the washer. Use adjustable pliers to tighten couplings an additional two-thirds turn. Repeat this step with a second hose for cold water faucet

Clearwater lines

• Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to prevent clogs. Water should run until clear. Make note of which hose is connected to hot water to help in attaching hoses to the washer correctly.

Connect inlet hoses to the washer

IMPORTANT: To reduce the risk of hose failure, replace the hoses every 5 years. Record hose installation or replacement dates for future reference.

• Do not overtighten the hose or use tape or sealants on the valve. Damage to the valves can result.
• Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. Attach the hot water hose to the red hot water inlet valve. Screw coupling by hand until it is snug. Use pliers to tighten couplings an additional two-thirds turn. Repeat with the cold water inlet valve.

Check for leaks Turn on water faucets to check for leaks. A small amount of water may enter the washer. It will drain later.

Secure drain hose Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with a cable tie. It is the responsibility of the installer to install and secure the drain hose into the provided plumbing/drain in a manner that will avoid the drain hose coming out of or leaking from the plumbing/drain.

Level Washer
NOTE: Level washer properly to reduce excess noise and vibration.

Check the levelness of the washer

Move the washer to its final location. Place a level on the top edges of the washer. Use the side seam as a guide to check the levelness of the sides. Check levelness of front using a lid, as shown. Rock washer back and forth to make sure all four feet make solid contact with the floor. If the washer is level, skip stepping 15.

Adjust leveling feet

If the washer is not level:
Use adjustable pliers to turn the plastic leveling foot counterclockwise to lower the washer or clockwise to raise the washer. Recheck levelness of washer and repeat as needed.

HELPFUL TIPS:

• You may need to adjust two different feet to level your unit. Ensure each foot remains secured to the washer’s base.
• You may want to prop an upfront washer about 4″ (102 mm) with a wood block or similar object that will support weight of washer.

WARNING
Electrical Shock Hazard:

• Plug into a grounded 3-prong outlet.
• Do not remove the ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

Plug into a grounded 3-prong outlet

Complete Installation Checklist

• Check electrical requirements. Be sure you have the correct electrical supply and recommended grounding method.
• Check that all parts are now installed. If there is an extra part, go back through the steps to see what was skipped.
• Check that you have all of your tools.
• Check that shipping material was completely removed from washer.
• Check that the washer is level.
• Check that the water faucet is on.
• Check for leaks around faucets and inlet hoses.
• Remove protective film from the console and any tape remaining on the washer.
• Check that washer is plugged into a grounded 3-prong outlet.
• Dispose of/recycle all packaging materials.
• Read the “Washer Maintenance and Care” section.
• To test and clean your washer, measure 1/2 of the normal recommended amount of powdered or liquid HE detergent and pour it into washer basket or detergent dispenser (on some models). Close lid. Select any cycle. Start washer and allow to complete full cycle.

DOWNLOAD RESOURCES

• MAYTAG MVW4505MW 4.5 Cu. Ft. Top Load Washer [pdf] Owner’s Manual MVW4505MW, 4.5 Cu. Ft. Top Load Washer, MVW4505MW 4.5 Cu. Ft. Top Load Washer
• Read more:  https://manuals.plus/maytag/mvw4505mw-4-5-cu-ft-top-load-washer-manual#ixzz7huGrD6Bq

FAQ’S

What is the difference between the Maytag MVW4505MW and the MVW4505?

The only difference between the two models is that the MVW4505MW has a stainless steel tub and the MVW4505 does not. Other than that, they are identical.

How do I use my washer?

Your washer has a variety of cycles to choose from, depending on what you’re washing. You can either use your washer’s controls to select a cycle or you can use your washer’s SmartDispense feature to select a cycle. The SmartDispense feature allows you to select a cycle by simply pressing one of the SmartDispense buttons. If you want to select a cycle manually, you can do so by pressing one of the cycle buttons on your control panel. When you press one of these buttons, your washer will automatically select the right amount of water for that cycle. You can also adjust how much water your washer uses by pressing one of your water level buttons on your control panel. Your washer has several different water level buttons, each of which will add more or less water to your wash load, depending on which button you press.

My washer makes loud noises when it’s running. Is this normal?

Yes! Your washer makes loud noises when it’s running because it’s working hard to clean your clothes for you! If this noise bothers you, try adding more clothes to your wash load or try using less water in your wash load. This will make it easier for your washer to get all of your clothes clean!

How do I remove lint from my Maytag MVW4505MW?

Lint can become trapped in various parts of your washing machine over time, including in or around its drain pump filter, in or around its drain hose filter (located on top of its drain pump), inside its pump filter (located under its lid), inside its agitator (located under its lid), and inside its tub (located under its lid). To remove lint from any of these areas, first unplug your washing machine from its power source and then remove its top lid by turning it counterclockwise until it comes off. Once you’ve removed its top lid, look inside each area listed above for any lint buildup and remove as much as possible with either your hand or a vacuum cleaner attachment before reinstalling your washing machine’s top lid and plugging it back into an electrical outlet.

When did they stop making Maytag?

When Maytag closed its doors in 2007, it was a rough transition. At the time, some 2,000 people were building washers and dryers at the old Maytag manufacturing facility.

Where is the filter on a Maytag top load washer?

All modern Maytag washers have filters that should be regularly cleaned every 3-6 months to prevent harmful lint buildup or clogs. In top-loading machines the filters are in the center of the agitator tube. They can be removed by taking off the agitator cap and pulling the filter upward.

How do you clean a Maytag top load washer?

CLEAN THE WASHER TUB
Remove any items left in the tub.
Add an affresh® washing machine cleaner tablet to the bottom of the tub.
Close the door and select your washer’s cleaning cycle.
For top load washers, when the cycle ends, run a rinse and spin cycle to clear away any excess cleansers.

Can I use vinegar in my Maytag washer?

Mix 1/4 cup with the same amount of water and add it to the detergent slot of your washing machine. Then, in the drum of the machine, add two cups of white vinegar, suggests Reviewed.com Laundry. Run a normal load and allow the baking soda and vinegar to work their magic.

Will a 4.5 cu ft washer fit a king size comforter?

Yes, a king-size comforter can be washed in the 4.5 cu ft.

What does the extra power button do on a Maytag washer?

The Extra Power button boosts stain-fighting performance on any wash cycle with a dual-temperature wash.

How do I reset my Maytag top load washer to factory settings?

Press power/cancel first. Next, pick a fresh cycle to run. Press start/pause to reset your Maytag washer. Run a test load afterward to confirm that the washer has reset.

How do I force my Maytag washer to drain?

Here’s how to manually drain water from a Maytag washing machine: Pull the washer away from the wall and turn off its power and water connections. Scoop out any remaining water in the washer drum. Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.

MAYTAG MVW4505MW 4.5 Cu. Ft. Top Load Washer
www://maytag.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>