ENS E12W SIP Door Phone WiFi with Facial Recognition User Guide

June 5, 2024
ENS

ENS-LOHO

ENS E12W SIP Door Phone WiFi with Facial Recognition

ENS-E12W-SIP-Door-
Phon-WiFi-with-Facial-Recognition-PRODUCT

Power-On Operation

Power on the device with 12V/1A power supply and wait until the device Call button light turns RED breathing light and hear the bee tone from El2W. ENS-
E12W-SIP-Door-Phon-WiFi-with-Facial-Recognition-FIG-1

Wi-Fi Configuration

Press the Tamper-proof button three times to enter the Wi-Fi scanning mode as indicated by the BLUE flashing light on the card reader area. And wait until the BLUE light stays constant when the device has finished Wi-Fi scanning and entered Network Pre-configuration mode, which lasts for only 20 seconds before it expires. ENS-E12W-SIP-Door-Phon-WiFi-with-Facial-Recognition-
FIG-2

Before Network Pre-configuration mode expires, long press the Call button for 3 seconds to enter the Network Configuration mode, when the device will automatically enable its hotspot feature while creating a hotspot access connection named El2-XXXX with no access password. “XXXX” is the last four digits of the device’s MAC address.

Open the WLAN feature on your mobile phone, find the Wi-Fi named “El2-XXXX”, and click “connect”. During this process, the Call button BLUE light will keep flashing. And now you will have only 5 minutes to finish the device Network configuration on your mobile phone via Hotspot because both the Network Pre- configuration mode and Network Configuration mode will expire in 5 minutes. ENS-E12W-SIP-Door-Phon-WiFi-with-Facial-Recognition-
FIG-4

After your mobile phone is connected to the hotspot successfully, your mobile phone will automatically open the browser and enter the Wi-Fi Configuration page. You can also type the hotspot IP address 192.168.188.10 on the mobile phone’s browser to enter the configuration page. Now, you can select the Wi-Fi network you want the device to be connected to, enter the corresponding Wi-Fi password, and tap Connect button. ENS-E12W-SIP-Door-Phon-WiFi-with-Facial-
Recognition-FIG-5

During the connection process, the Call button BLUE light keeps flashing. If successfully connected to the Wi-Fi, you will see the Call button BLUE light stays on and hear a prompt sound for the successful connection. If the connection failed, you will see a PURPLE flashing light, requiring you to proceed from step 1.

Note:
In this step, you can always press the Tamper-proof button 3 times to proceed from the steps if anything goes wrong such as having entered the incorrect password. ENS-E12W-SIP-Door-Phon-WiFi-with-Facial-Recognition-
FIG-6

Indicator Light


Mode

| ****

Indicator Status

---|---
Power on without network| Call button: Red light flashes once every 400ms


Wi-Fi scanning mode

| ****

Card reader area: flashes once every 400ms. Call button: always off


Pre-configuration mode

| ****

Card reader area: always on Call button: always off


Network configuration mode

| Card reader area: always off

Call button: Blue light flashes once every 400ms




Connect Wi-Fi

| Success:

Card reader: always off

Call butt on: blu e light is always on

Failed:

Card reader: always off

Call butt on Purple e light keeps flashing for 400ms

Notice Information

Information contained in this document is believed to be accurate and reliable at the time of printing. This document is subject to change without notice, any update to this document can be viewed on Akuvox’s website: http://www.akuvox­.com © Copyright 2021 Akuvox Ltd. All rights reserved.

AKUVOX (XIAMEN) NETWORKS CO., LTD.
ADD: 10/F, NO.56 GUANRI ROAD, SOFTWARE PARK 11, XIAMEN 361009, CHINA www.akuvox.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals