PYLE PLRGSW104BK 10 Inch Slim Waterproof Subwoofer User Guide
- June 4, 2024
- Pyle
Table of Contents
PLRGSW104BK 10 Inch Slim Waterproof Subwoofer
**User Guide
**
PLRGSW104WT – PLRGSW104BK 10” Slim Waterproof Subwoofer
400 Watts at Dual 4-Ohms Car Audio Powered Subwoofer with Multi-Color RGB
Lights and Remote Control, PP Cone with Rubber Edge
Features:
- 10” Slim Waterproof Subwoofer
- Completely Waterproof
- For Marine or Car Use
- Multi-Color RGB Lights and Remote Control
- PP Cone with Rubber Edge
- High-Powered Car Subwoofer
- Lab Tested Pro Audio Woofer Performance
- Massive Butyl Rubber Surround
- High Strength Engineering Plastic Basket
- Quick Connect Speaker Terminal
- Compatible with Sealed Enclosure Speaker Box Audio Setup
- Impressive Bass Response, Low-Resonance Frequency Output
- Designed for Custom Audio Car, Truck, Mobile Vehicle Applications
Connection Diagram
Installation Guide
Cut the drywall.
Note: Always allow at least one-half inch between a wall stud
and the speaker cutout or the locking tabs will not be able to swivel into
place.| Connect the speaker wires to the speaker.
Screw down each of the four Phillips head screws. The locking tabs will swivel
into place and secure
the unit to the rear surface of the drywall. Put in the strips of adhesive to
secure the grille.| Replace the metal grille.
Remote Control
1. Turn On/Standby: Press this key to turn ON the unit or switch to
standby mode. At power on, the unit will automatically turn ON and restore to
its previous status.
2/9. Dynamic Mode Adjust: Switch to dynamic mode from static color or
switch between dynamic modes.
3/10. Dynamic Speed Adjust: Adjust dynamic playing speed. Press SPEED+ to
increase speed and press SPEED- to decrease. The unit will switch to dynamic
mode if pressing this key at static color mode.
4/5. Static Color Adjust: Switch to static color mode from dynamic mode
or switch between static colors.
6. Direct Color Select: Shortcut key to static colors. When pressing the
specific color key, LED will play the same static color. The direct colors are
included in the ‘COLOR+’ and ‘COLOR-‘ operations.
7/8. Brightness Adjust: Adjust static color brightness. Press BRIGHT+ to
increase brightness and press BRIGHT- to decrease. The unit will switch to
static color mode if this key is pressed at dynamic mode.
11. Demo Mode: Press this key to switch to Demo mode. At demo mode, it
plays 17 dynamic modes in the loop, each mode repeat 3 times.
What’s in the Box:
- 10” Slim Waterproof Subwoofer; RGB wire; remote control
Technical Specs:
-
Construction Materials: Engineered ABS
-
Power Handling: 400W Max, 200W RMS
-
Impedance: Dual 4 Ohms
-
Voice Coil: 2.0” -in
-
Voice Coil Type: High-Temp Aluminum
-
Magnet Size: 40 Oz
-
Magnet Type: Barium Ferrite Magnet
-
Frequency Response: 30Hz – 200Hz
-
Sensitivity: 92 dB
-
Remote Control Battery Operated, Requires (1) x `CR2025′ Batteries
-
Battery Type: 3V Lithium Battery
-
Battery Life: Up to 2+ Hours
-
Product Dimensions: 10.5” x 9.3” x 3.1” inches
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www.PyleUSA.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>