VARMA TEC 550 Varma Tandem Radio Instruction Manual
- June 4, 2024
- VARMA TEC
Table of Contents
TEC 550 Varma Tandem Radio
Instruction Manual
STAR PROGETTI RADIO ELECTRIC HEATERS
MADE IN ITALY
| no. | CODE | COLOUR | RATED POWER | RATED VOLTAGE |
|---|---|---|---|---|
| 1 | 550/20NR | BLACK | 1 x 2000W | 230Vac |
| 2 | 550/20BR | WHITE | 1 x 2000W | 230Vac |
Radio remote control unit code PTVTEL
15 CHANNELS
CHANNEL NO| FUNCTION
PP| REMOVE RADIO CONTROLS AND DETECTORS
12-Jan| HEATER MANAGEMENT
13| SELF-LEARNING
14| ENABLE / DISABLE
PIR DETECTOR
15| ST15 PIR DETECTOR TRANSMISSION
• Degree of protection: IP20
• Battery: 3 V type CR2450
• Dimensions: 13544*10 mm
• Weight: 40 g
• Operating frequency: 433 MHz
• two-digit display screen
• 15 channels| • 5 buttons
• Colour: white
• Material: ABS, plastic
• Certificate: EC ROHS
• Transmission distance: 20 m
• Type of coding: Learning code: EV1527
---|---
START
After installing the heater (Fig. a) on the wall:
Operate the main switch. Fig.1
The heater is now powered by 220-240Vac mains voltage. A green light flashes
for a few seconds to confirm the operation.Fig. 2
STORAGE OF 1 RADIO REMOTE CONTROL UNIT WITH 1 HEATER
ALWAYS CARRY OUT OPERATIONS WITH ONLY ONE HEATER CONNECTED WITH MAINS VOLTAGE.
Take the radio remote control unit cod. PTVTEL:
- use the “+” and “-” buttons to select channel 13 Fig. 3 and then press the button as shown in Fig. 4
- The blue led of the heater starts flashing Fig.5
Take the radio remote control unit cod. PTVTEL:
- Within 10 seconds use the “+” and “-” buttons to select the channel [1-12] selected for the assignment. Example «channel 1» Fig.6
- Immediately afterward press the button as shown in Fig. 7.
- The blue LED on the heater goes out to confirm that the storage operation is complete.
Fig.8
N.B. If programming does not work, repeat programming
Take the radio remote control unit cod. PTVTEL:
- Repeat the operations of the previous chapter by selecting the channels of your choice [1-12].
- All heaters can also be assigned to the same channel.
- It is also possible to form groups of heaters by creating heating zones.
YOU CAN STORE A MAXIMUM OF THREE RADIO REMOTE CONTROL UNITS PLUS A PIR OR ONLY FOUR RADIO REMOTE CONTROL UNITS
OPERATION OF THE REMOTE CONTROL
Switching ON
Take the radio command code no. PTVTEL:
- On channel «1», press the button as shown in fig. 9
- Red LED lights up Fig.10
Setting power.
Take the radio remote control unit cod. PTVTEL:
- On channel «1», press the button as shown in fig. 11
- Yellow LED lights up Fig.12 medium power
- On channel «1», press the button as shown in fig. 13
- Green LED lights up Fig.14 maximum power
When switched on for the first time with the power supply switched on
(230Vac), pressing the ON button will set the controller to idle (red LED).
During the following starts, pressing the ON button will set the controller to
the last power selection set (status MEMORY).
*Enable PIR from remote control**
Take the supplied radio control unit cod. PTVTEL
- By using the “+” and “-” buttons select channel 14 Fig.15 and immediately after pressing the button as shown in Fig. 16
- The blue LED on the heater starts flashing twice to confirm the operation Fig.17
*Disable PIR from remote control**
Take the supplied radio control unit cod. PTVTEL
- When switched on for the first time with the power supply switched on (230Vac), pressing the ON button will set the controller to idle (red LED).
- During the following starts, pressing the ON button will set the controller to the last power selection set (status MEMORY).
CLEARING THE HEATER MEMORY
REMOVE RADIO CONTROLS AND DETECTORS
Take the radio remote control unit cod. PTVTEL:
- By using the “+” and “-” buttons select channel PP Fig.19 and immediately after pressing the button as shown in Fig. 20
- The blue LED on the heater starts flashing to confirm the cancellation operation has been carried out Fig. 21
N.B. If deletion does not work, please repeat the operation.
In case of need, please contact our Technical Office tel. (+39) 02 90639261
TROUBLESHOOTING
| PROBLEM | CAUSES | SOLUTIONS |
|---|---|---|
| The radio remote control does not work | • Batteries are low | • Replace |
batteries Fig. 22
The radio remote control works but does not control the heater| • PTVTEL has
not been stored with the heater| • Store PTVTEL read chapter «STORAGE OF 1
RADIO REMOTE CONTROL WITH 1 RADIO HEATER»
The remote control does not store with heater| • Heater memory full if 4
devices are stored| • Clear the memory by removing one of the four previously-
stored PTVTELs, see chapter «CLEARING THE HEATER MEMORY»
The product does not switch on| • No mains voltage
• Incorrectly mounted plug or damaged cable.
• The remote control unit does not work| • Check that there is voltage in the
power cable and try again.
• Check that the plug is fitted correctly or replace the cable.
• Check the remote control
The heating element does not turn on at any set power level| • the heating
element is damaged.| • Contact technical support (+39 02 90639261 then dial 2)
or your dealer
Power control does not work| • The controller element is damaged.| • Contact
technical support
(+39 02 90639261 then dial 2)
or your dealer
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>