SIGMA BUSTER 800 Sport Helmet Light User Manual
- June 4, 2024
- SIGMA
Table of Contents
SIGMA BUSTER 800 Sport Helmet Light
CE INFORMATION
EN SIGMA-ELEKTRO GmbH hereby declares that the BUSTER 800 comply with the
fundamental requirements and other relevant regulations of Directive
2014/30/EU and RoHS Directive 2011/65/EU. You can fi nd the CE declaration at:
ce.sigmasport.com/buster800
WARNING
Possibly dangerous optical radiation! Never look directly into the lamp or
point it at other people‘s eyes while it is in operation.
FCC DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation. The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.
This equipment should be installed and operated with a minimum distance of 5
millimeters between the radiator and your body.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in
this manual. The further RF exposure reduction can be achieved if the product
can be kept as far as possible from the user body or set the device to lower
output power if such function is available.
UKCA STATEMENT
We, SIGMA-ELEKTRO GmbH, declare that the equipment above has been tested in
our facility and found compliance with the requirement limits of applicable
standards, in accordance with the Radio Equipment Regulations 2017 and the
Restriction of the Use of Certain Hazardous Sub-stances in Electrical and
Electronic Equipment Regulations 2012. The test record, data evaluation and
Equipment Under Test (EUT) confi gurations represented herein are true and
accurate under the standards herein specifi ed.
ACCESSORIES
-
Helmet Bracket Set
-
Silicone Bracket
-
Charging cable USB-C
-
Screw-Bracket Mount
-
Charger
-
Adapter for Action Camera Mount
MOUNTING
SCREW-BRACKET MOUNT
Adjust the BUSTER 800 so that it does not blind other road users. The BUSTER
800 must be securely attached to the bike and light distribution must not be
obstructed.
5 MODES
THERMAL PROTECTION CIRCUIT:
The lamp is sufficiently cooled while driving. If the temperature of the lamp
rises above 60 °C, it automatically switches to the next weaker mode.
MODE MEMORY FUNCTION
PRESET MODE PROFILES
PROFILE SELECTION:
You can adapt your BUSTER 800 individually to your requirements. For this
purpose, the lamp has 5 different profiles that you can select as follows.
Hold down the ON/OFF button for longer than 5 seconds when it is switched off,
then you will get to the profile selection. The lamp fl ashes once for profile 1,
twice for profile 2 and so on. To select the desired profile, press the ON/OFF
button once. Your selection is confirmed by four short fl ashes of the front
LED.
BATTERY INDICATOR
BATTERY STATUS
In the switched-off state, 1x short click shows the current battery status.
CHARGING
- Charge the light only if the ambient temperature is between +10 °C and +45 °C (50 °F and 110 °F). This protects the battery from damage and increases its service life.
- Ensure that the USB sealing marked red is always closed correctly after charging.
- No energy can be transferred out through the USB-C connection.
CHARGING INDICATOR
TECHNICAL DATA
-
Charging Temperature:
+10°C to +45°C
50 °F and 110 °F -
Battery Type:
3.7 V, 3500 mAh
Max power:
3W -
Water and Dust rating:
IP44
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>