ALDI 705715 Ferrex 65 W Multifunctional Sharpener User Manual
- June 4, 2024
- ALDI
Table of Contents
FOREX
705715 65 W
MULTIFUNCTIONAL SHARPENER
Product Info
http://help.tools
Read all safety warnings and all instructions thoroughly before operating this product. Ensure you keep your manual in a safe place for future reference. IM ed 3; 05/2022
QR codes take you where you want to go quickly and easily
Whether you require product information, spare parts, or accessories,
details on warranties or aftersales service, or if you want to watch a product
demonstration video, our QR codes will take you there in no time at all.
What is a QR code?
A QR-code (QR=Quick Response) is a type of matrix that can be read with a
smartphone camera that contains a link to a website or contact details, for
example. Advantage: You are not required to manually enter a website address
or contact details.
How it works
To scan the QR code, all you need is a smartphone with QR code reader software
and an Internet connection. This type of software can be downloaded for free
from your smartphone’s app store.
Try it out now
Just scan the QR code with your smartphone and find out more about the Aldi
product you have purchased.
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-
registration/TO
KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION.
The product is guaranteed to be free from defects in workmanship and parts for
a period of 12 months from the date of purchase. Defects that occur within
this warranty period, under normal use and care, will be repaired, replaced or
refunded at our discretion. The benefits conferred by this warranty are in
addition to all rights and remedies in respect of the product that the
consumer has under the Competition and Consumer Act 2010 and similar state and
territory laws. Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
Congratulations on the purchase of your FERREX® 65 W* Multifunctional
Sharpener. When you open your packaging, first remove all items and check
there are no parts damaged or missing. If you find anything wrong, do not
operate the product until the parts have been replaced or the fault has been
rectified. Failure to do so could result in serious personal injury.
*Intended use of the 65 W Multifunctional Sharpener
NOTE:** This product is for private domestic DIY use only. It is not
suitable for commercial, industrial, or trade use. This multi-task sharpener
tool includes three working modules:
- HSS (High-Speed Steel) drill sharpener — Sharpens all high-speed steel drill bits from 3 mm to 13 mm.
- Knife & Scissor Sharpener — Sharpens all straight-edged knives and scissors.
- Chisel & Planer Sharpener — Regrinds chisel and planer blades from 6 mm to 51 mm in width. Use the sharpener and modules only for intended applications. This user manual contains important information on how to use the 65 W* Multifunctional Sharpener. Read this user manual carefully, in particular the safety instructions, before using the product. Failure to follow this user manual may lead to severe injuries or product damage. Keep this user manual for further reference.
IMPORTANT INFORMATION.
NOTE: First-time users or inexperienced operators pay particular
attention to the operation of the 65 W Multifunctional Sharpener, including
details of starting and stopping and correct use of the 65 W Multifunctional
Sharpener on pages 10-15, as well as the maintenance instructions on page 15.
Contents of carton
1 x 65 W* Multifunctional Sharpener | Knives And Scissors |
---|---|
3 x Modules Including Drilling, | 1 x Instruction Manual |
Sharpening Chisels, Sharpening | 1 x Warranty Card & Certificate |
Description of symbols
The instruction manual or rating plate on your product may show symbols. These represent important information about the product or instructions on its use.
| To reduce the risk of injury, the user must read the instruction manual
---|---
| Double insulation
| Warning
| Wear ear protection
| Wear eye protection
| Wear dust mask
| Conforms to relevant standards for electrical safety and electromagnetic
compatibility.
| 12 Months Warranty Period.
| The box is recyclable at the curbside.
| The Insert is recyclable at the curbside.
General Safety Instructions
WARNING! Read all safety warnings, instructions, illustrations, and
specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire, and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
-
Work area safety
a) Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. -
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is arthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.3) -
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second. -
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations. -
Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. -
Recommendation
The recommendation is that the tool always is used with a residual current device having a rated residual current of 30 mA or less. Bench grinder safety warnings
a) Do not use a damaged accessory. Before each use, inspect the accessory such as abrasive wheels for chips and cracks. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
b) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
c) Never grind on the sides of a grinding wheel. Grinding on the side can cause the wheel to break and fly apart.
Parts List
1. Grinding wheel | 9. Knife sharpening slot |
---|---|
2. HSS drill sharpener module | 10. On/off switch |
3. Clamp | 11. Chisel & planer sharpener module |
4. Setting slot | 12. Integral magnet |
5. Clamping ring | 13. Eye protective shield |
6. “V” guide | 14. Angle adjustable knob |
7. Knife & scissor sharpener module | 15. Bench mountable hole/s |
8. Scissor sharpening slot
Operating instructions
NOTE: Before using the sharpener, read the instruction manual carefully.
| Mounting to a bench
NOTE: There are four bench mountable holes (15)on the base of the
sharpener. Use four screws (not provided) to fix it onto a stable position
before use
---|---
| Switching on and off
1. Insert the plug into the mains power socket and switch on the power.
2. To turn the sharpener on, move the on/off switch(10) to the “I” Position.
3. To turn the sharpener off, move the on/off switch(10) to the “O” position
(See Fig. A).
Sharpening HSS drill bits
WARNING: Before assembling the HSS drill sharpener module (2) , be sure
the sharpener is unplugged and the on/off switch (10) is in the of “O’’
position. 1) Slide the HSS drill sharpener module onto the side of the
sharpener with the grinding wheel
-
Make sure the HSS drill sharpener module is locked in place (See Fig. B1, B2).
-
Remove the clamp (3) from the clamp holder and insert the HSS drill bit (not supplied) to be sharpened. Rotate the clamping ring (5) in a clockwise direction to tighten the clamp lightly to leave the drill bit still free to move (See Fig. B3, B4).
-
Place the clamp containing your drill bit into thesetting slot (4), using the grooves in the side to lower it in correctly (See Fig. B5).
-
Move the drill bit forward so that it lays in the “V” guide (6) and touches the metal end stop (See Fig. B5).
-
Turn the drill bit until the “V” guide (6) fully drops over it. All four drill bit corners should now be touching the “V” guide (6) sides.
-
Ensure that the drill and holder are fully down in the setting slot. With the drill bit in this position, tighten the clamping ring (5) in a clockwise direction (See Fig. B6).
-
Lift up the “V” guide (6) and remove the clamp and drill bit (See Fig. B7).
-
Transfer the clamp and drill bit into the clamp holder (See Fig. B8).
-
Insert the plug into the mains power socket and switch on the power. Move the on/off switch (10) to the “I” position to turn the sharpener on.
-
Move the clamp holder from side to side as indicated by the arrow on the sharpener, securing with light finger pressure (See Fig. B9).
-
Switch the device off. Remove drill bit and clamp and turn over. Repeat Step 10.
-
Check the leading edge of both flutes is equally sharp. They should meet exactly in the middle as in Fig B10, not B11.
-
When you have finished sharpening, turn off the sharpener by moving the on/off switch (10) to the “O” position.
WARNING: Before removing the module, ensure the grinding wheel has
stopped.
Sharpening knives
WARNING: Before assembling the knife & scissor sharpener module (7) , be
sure the sharpener is unplugged and the on/off switch (10) is in Off ‘’O’’
position.
NOTE: This module is suitable for all straight-edged, household knives
and scissors only. Do not use serrated-edged blades.
-
Slide the knife & scissor sharpener module (7) onto the side of the sharpener with the grinding wheel (1) . Make sure the knife & scissor sharpener module (7) is locked in place.
-
Insert the plug into the mains power socket and switch on the power. Move the on/off switch (10) to the “I” position to turn the sharpener on.
-
Hold the knife handle towards you and insert the blade end of the knife into the knife sharpening slot (9) (See Fig. C1).
-
As soon as the blade touches the grinding wheel (1) , draw it with light steady pressure across the wheel to the tip, then remove it. Do not press hard.
-
Insert the opposite side of the blade into the other top guide slot and repeat step 4 (See Fig. C2).
-
Repeat sharpening each side in turn until a clean sharp edge is attained.
-
When you have finished sharpening, turn off the sharpener by moving the on/off switch (10) to the “O” position. Before removing the module, ensure that the grinding wheel has stopped.
Sharpening scissors
WARNING: Before assembling the knife & scissor sharpener module (7) , be
sure the sharpener is unplugged and the on/off switch (10) is in the ‘’O’’
position.
NOTICE! This module is suitable for all straight-edged, household knives and
scissors only. Do not use serrated-edged blades.
- Slide the knife & scissor sharpener module (7) onto the side of the machine with the grinding wheel (1) . Make sure the knife & scissor sharpener module (7) is locked in place.
- Insert the plug into the mains power socket and switch on the power. Move the on/off switch (10) to the “I” position to turn the sharpener on.
- Open the scissors fully.
- Slide the first scissor blade through the scissor sharpening slot (8) . Keep the pivot of the scissors and another blade to the right-hand side (See Fig. D).
- Draw the blade across the grinding wheel (1) from pivot to tip. Use light steady pressure, do not press too hard.
- Remove and turn the scissors over to sharpen the second blade. Keep the pivot to the right and sharpen from pivot to tip.
- Repeat if necessary, until clean sharp edges are achieved.
- When you have finished sharpening, turn off the sharpener by moving the on/off switch (10) to the “O” position. Before removing the module, ensure that the grinding wheel has stopped.
Sharpening chisel & planer blades
Before assembling the chisel & planer sharpener module (11) , be sure the
sharpener is unplugged and the on/off switch (10) is in the ‘’O’’ position.
-
Slide the chisel & planer sharpener module(11) onto the side of the machine with the grinding wheel (1). Make sure the chisel & planer sharpener module (11) is locked in place.
-
Place the blade against the back lip of the plate. The magnet helps to hold it in place (See Fig. E1).
-
The sharpening angle must match the existing beveled angle on the blade tip. Adjust, if necessary
-
To alter the angle:
• Loosen the angle adjusting knob in an anticlockwise direction.
• Adjust the plate. The sharpening angle is indicated by the small arrow. The
adjustable grinding angle is from 15°to 50°. Make sure the blade edge touches
the grinding wheel.
• Tighten the angle adjusting knob (See Fig. E2).
- insert the plug into the mains power socket and switch on the power. Move the on/off switch(10) to the “I” position to turn the sharpener on.
- Slide the blade and plate with light steady pressure back and forth across the grinding wheel (1) in a continuous motion. Do not hold the blade stationary. This causes irregular sharpening (See Fig. E3).
- Gradually adjust the blade down The plate while sharpening. Do not press hard. Grind gradually, repeating the step (See Fig. E4).
- Remove the blade and make sure the beveled edge and tip are evenly sharp. If not, adjust the grinding angle. It is important that the sharpening angle matches the existing beveled angle of the blade. This avoids removing too much metal unnecessarily and keeps planer blades at their optimum shaving angle (See Fig. E5).
- When sharpening thin chisel blades, place the small chisel guide onto the plate to act as a spacer and sharpen as before (See Fig. E6).
- When you have finished sharpening, turn off the sharpener by moving the on/off switch (10) to the “O” position. Before removing the module, ensure the grinding wheel has stopped.
- Recommend that after grinding, the blade tip is honed on an oil stone.
Maintenance
Remove the plug from the mains power socket before carrying out any
adjustment, servicing, or maintenance.
Your sharpener requires no additional lubrication or maintenance. There are no
user-serviceable parts in your sharpener. Never use water or chemical cleaners
to clean your sharpener. Wipe clean with a dry cloth. Always store your
sharpener in a dry place. Keep the motor ventilation slots clean. Keep all
working controls free of dust. Occasionally you may see sparks through the
ventilation slots. This is normal and will not damage your sharpener. If the
supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Storage and cleaning
Clean the molded plastic housing of the machine using a soft brush and clean cloth. Do not use water, solvents or polishes. Remove all debris, especially from the motor cooling vents. Store in a secure, dry place out of the reach of children. Do not place other objects on the product.
Warranty
Your new FERREX® Multifunctional Sharpener will more than satisfy your
expectations. It has been manufactured under stringent FERREX®. Quality
Standards to meet superior performance criteria. You will find your new
Multifunctional Sharpener easy and safe to operate, and, with proper care, it
will give you many years of dependable service.
CAUTION. Carefully read through this entire instruction manual before
using your new FERREX® Multifunctional Sharpener. Take special care to heed
the Cautions and Warnings. Your FERREX® Multifunctional Sharpener has many
features that will make your job faster and easier. Safety, performance, and
dependability have been given top priority in the development of this FERREX®
Multifunctional Sharpener, making it easy to maintain and operate. Use only
FERREX® replacement parts for your product.
Non-conforming parts or modifications made to parts will void your warranty.
Environmental protection
Recycle unwanted materials instead of disposing of them as waste. All tools, hoses, and packaging should be sorted, taken to the local recycling center, and disposed of in an environmentally safe way.
What your 1-year warranty means
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly. In the
event of a product failure within its intended use over the course of the
first 1 year after the date of purchase, we will remedy the problem as quickly
as possible once it has been brought to our attention. In the unlikely event
of such an occurrence, or if you require any information about the product
please contact us via our after-sales support services, details of which can
be
found in this manual and on the product itself. After Sales Support TEL: 1300
889 028 or email:
info.aldi@positecgroup.com
Troubleshooting
Symptom | Possible causes | Solution |
---|---|---|
The product does not start | 1.1 Not connected to the power supply. |
1.2 The product is not turned on.
1.3 Power cord or plug is defective.| 1.1 Connect to the power supply.
12 To turn the sharpener on, move the on/off switch to the “r position.
13 Contact customer service.
The product does not work properly| 2.1 Grinding wheel is defective.| 2.1
Contact customer service.
The motor is
overheating| 3.1 Cooling vents may be obstructed by dust or other obstacles.|
3.1 Clean and clear vents. Do not cover with a hand during operation.
For further inquiries or issues associated with your 65 W* Multifunctional Sharpener, call our Customer Service on 1300 889 028 or email us at info.aldi@positecgroup.com
Technical Specifications
Voltage: | 220-240 V~50 Hz |
---|---|
Power Input: | 65 W S2: 8 min 25 W S1 |
No-load Speed: | 7000 /min |
Wheel Diameter: | Φ 51 mm |
Planer Blades Width: | 6 mm-51mm |
Drill Diameter: | 3 mm-13 mm |
Charger Protection Class: | /II |
Machine Weight: | 1.2 kg |
Product Dimensions: | 190 x 200 x 130 mm |
This 65 W * Multifunctional Sharpener complies with the following standards:
Safety: | AS/NZS 62841.1 AS/NZS 62841.3.4 |
---|---|
EMC: | EN 55014-1 EN 55014-2 EN 61000-3-2 EN 61000-3-3 |
ALDI guarantees that our exclusive brand products are developed to our stringent quality specifications. If you are not entirely satisfied with this product, please return it to your nearest ALDI store, within 60 days from the date of purchase, for a full refund or replacement, or take advantage of our after-sales support by calling the supplier’s Customer Service Hotline.
Made in China
FERREX® is a registered trademark of ALDI Stores
DISTRIBUTED BY:
ALDI STORES
1 SARGENTS ROAD
MINCHINBURY NSW 2770
www.aldi.com.au
AFTER-SALES SUPPORT
1300 889 028 (toll free)
e-mail:info.aldi@positecgroup.com
MODEL: BDS651 • 05/2022 • 705715
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>