Hunter 19359 Saddle Creek 5 Light Chandelier Instruction Manual

**Saddle Creek

For Models: 19359/19360/19361/19362**

Light Chandelier
Fixture weight ±2 lbs: 10.92 lbs (4.95 kg)

Hardware Service Kit

Glass

Here are the tools you’ll need to complete your installation:

INSTALLATION INSTRUCTIONS

WARNING

• To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
• The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
• All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.

READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning installation of the lighting fixture.

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (F) should be attached to the mounting bracket (A) with a washer (D) and a hex nut (E) in place. The other end should have the canopy loop (G) attached. Unscrew the canopy loop ring (I) from the canopy loop (G). Depending on the placement of your junction box the position of the threaded post (F) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and placing canopy (H) over the canopy loop (G), so that it is flush with the ceiling. Adjust the position of a threaded post (F) on the mounting bracket (A) so that the canopy (H) covers at least half of the exterior threads on the canopy loop (G) while it is securely connected to the threaded post (F). The threaded post (F) can be adjusted by loosening the hex nut (E) to allow movement of the threaded post (F) on the mounting bracket (A). Once the ideal position of the threaded post (F) is determined, tighten up the hex nut (E) onto the threaded post (F) just beneath the mounting bracket (A) to secure the threaded post in place.

ASSEMBLING THE FIXTURE

Thread the wires through and attach the center rod (O) to the hexagon nut (P) of the fixture, then slide the rod cover (N) and lock ring (M) onto the center rod (O) and secure with the hanging ring (L). By measuring, determine the correct number of chain links needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach one quick- connect link (J) to each end of the chain (K). Use one quick-connect link (J) to attach chain (K) to the hanging ring (L) and securely close. Feed the fixture wires up through the chain (every three links or so) pulling the wires until taut. Slide canopy loop ring (I) and canopy (H) onto the chain/wire. Use the remaining quick-connect link (J) to attach chain (K) to the canopy loop (G)and thread the wires through. To shorten the fixture, trim the wires to the desired length. Leave at least 8 to 10 inches of wire in addition to the desired length. Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

CONNECTING THE WIRES

Have a helper support the fixture’s weight while completing the wiring. Attach the fixture wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (C) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.

FINISHING THE INSTALLATION

Place the canopy (H) flush to the ceiling and slide the canopy loop ring (I) up beneath the canopy. Tightly screw the canopy loop ring (I) onto the canopy loop (G) to properly secure the canopy (H) in place. Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Secure glass (S) onto the socket (Q) with screws (R). Your installation is now complete. Turn on the power and test.

CLEANING TIPS

Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray the cleaner directly onto the fixture.
Hunter Pro Tip:
Let the tool do the work! Use chain pliers to easily open and close chain links to shorten your fixture.

Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the downloads. Threaded posts may also be removed for easier wire access.

©2022 Hunter Fan Co.
ML284
r_031522

Documents / Resources

| Hunter 19359 Saddle Creek 5 Light Chandelier [pdf] Instruction Manual
19359, 19360, 19361, 19362, Saddle Creek, 5 Light Chandelier, Saddle Creek 5 Light Chandelier, 19359 Saddle Creek 5 Light Chandelier, Chandelier
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>