iArmor IA-S106H Side Steps Armor Installation Guide
- June 4, 2024
- iArmor
Table of Contents
iArmor IA-S106H Side Steps Armor
Product Information
Specifications
- Part Number: IA-S106H
- Mounting Type: Rocker Panel Mount
- Installation Method: No Drilling/Trimming Required
Product Usage Instructions
- Remove all contents from the box and verify all parts are present.
- Read the instructions carefully before starting the installation.
- It is recommended to seek assistance during installation.
- Thank you for choosing our product!
FAQ
- Q: Is professional installation recommended?
- A: Yes, we strongly recommend professional installation for the best results. We are not responsible for any damage caused by incorrect installation.
- Q: What should I do if any parts are missing from the box?
- A: Please contact our customer support at info@iarmorauto.com for assistance in getting the missing parts.
BEFORE INSTALLATION
- REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. THANK YOU FOR CHOOSING OUR PRODUCT!
- ROCKER PANEL MOUNT
- NO DRILLING / TRIMMING REQUIRED
Torque Value
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | √ |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Hardware Package
Hardware Package A (For Bracket Installation)
Item| QTY| Description| Item| QTY| Description
1#| 4| U Brackets| 7#| 12| M8 Lock Washers
2#| 4| M8X1.25 Nut Plates| 8#| 8| M8X1.25 Hex Nuts
3#| 4| M8X1.25-35mm Hex Bolts| 9#| 8| M6X1-25mm Inner Hex Bolts
4#| 8| M8X1.25-25mm Hex Bolts| 10#| 8| M6 Large Flat Washers
5#| 4| M8 Large Flat Washers| 11#| 8| M6 Flat Washers
6#| 16| M8 Flat Washers| 12#| 8| M6X1 Nylon Lock Nuts
Hardware Package B (For Step Bar Installation)
Item| QTY| Description| Item| QTY| Description
1#| 4| M8X1.25-55mm Carriage Bolts| 3#| 4| M8 Lock Washers
2#| 4| M8 Large Flat Washers| 4#| 4| M8 Hex Nuts
Installation Instructions
The instructions here are for your reference only. We strongly recommend the professional installer for the best result. We are not responsible for any damage caused by the installation.
STEP 1
- Start installation toward the front of the driver’s side of the vehicle. Determine if the vehicle has an open floor panel or a threaded hole in the floor panel for the top tab on the Bracket, (Figs 1 & 2).
STEP 2
- Assemble (2) Driver Side Mounting Brackets and Driver Support Brackets as shown, (Figs 3-4). Do not fully tighten the hardware at this time.
STEP 3
- Select the assembled Driver Front Mounting Bracket.
Vehicles open mounting location
- Insert (1) M8 Nut Plate into the large square opening in the floor panel. Line up the threaded nut with the small hole in line with the tab on the Bracket, (Figs 5A & 5B). Bolt the Mounting Bracket to the Nut Plate with (1) M8X1.25-35mm Hex Bolt, (1) M8 Lock
- Washer and (1) M8 Large Flat Washer. Do not fully tighten hardware at this time, (Fig 6).
Vehicles with factory threaded holes in the floor panel
- Bolt the tab on the Mounting Bracket to the threaded hole in the floor panel with (1) M8X1.25-35mm Hex Bolt, (1) M8 Lock Washer and (1) M8 Large Flat Washer, (Figs 6). Do not fully tighten the hardware at this time.
STEP 4
- Line up the Support Bracket with the (2) factory holes on the pinch weld. Bolt the Support Bracket to the back of the pinch weld using the included (2) M6X1-25mm Inner Hex Bolts, (2) M6 Flat Washers, (against pinch weld), (2) M6 Large Flat Washers, (inside against the bracket) and (2) M6X1 Nylon Lock Nuts, (Fig 7). Do not fully tighten the hardware at this time.
STEP 5
Move to the Driver Side Rear Mounting Location, (Fig 8A). Repeat Steps 1-3 for
the assembled Driver Rear Mounting Bracket installation, (Figs 2 & 8B).
NOTE: Determine the correct Rear Support Bracket installation procedure
according to the model year of the vehicle: A. 2007 Model: Line up the centre
hole on the Support Bracket to the pinch weld, secure by using (1) M6X1-25mm
Inner Hex Bolt, (1) M6 Flat Washer (outside), (1) M6 Large Flat Washer,
(inside against bracket), and (1) M6X1 Nylon Lock Nut to attach the rear
bracket to the back of the pinch weld, (Fig 9).
B. 2008-UP Models: Attach the Support Bracket to the back of the pinch weld by
using (2) M6X1-25mm Inner Hex Bolts, (2) M6 Flat Washers (outside), (2) M6
Large Flat Washers (inside against the bracket) and (2) M6X1 Nylon Lock Nuts,
(Fig 10).
STEP 6
- Once all (2) Driver side mounting brackets are installed, select and attach the Driver Side Step Bar onto the Mounting Brack-ets with (2) U Brackets, (2) M8X1.25-55mm Carriage Bolts, (2) M8 Flat Washers, (2) M8 Lock Washers and (2) M8X1.25 Hex Nuts (Fig 11). Do not fully tighten the hardware at this time.
- Properly level and adjust the Step Bar and fully tighten all hardware.
STEP 7
- Move to the other side of the vehicle. Repeat Steps 1-6 to install the other side step bar.
Installation completed.
Attention
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
- To protect your bars/boards, please use mild soap/non-abrasive products for cleaning only.
NOTE: Torque all M8 X1.25-55mm Carriage Bolts to 16~18 Ib-ft. Don’t over- tighten, or the square bars will be damaged by the brackets
Customer Support: info@iarmorauto.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>