Bluedio H+ T2+（could-based version） User Manual

USER MANUAL
Model: Bluedio H+ T2+

Bluetooth 5.0 Headset
Read this user manual carefully and completely before using the product.

Important safety information

1. Do not listen at high volume levels for long periods of time to prevent hearing damage.
2. Do not use the product if there is any potential danger.
3. Do not turn the volume too high to hear sounds around you, turn down the volume if you feel a tinnitus or the volume is too high.
4. Do not use the product in an environment that requires your special attention(e.g. in traffic).
5. Keep the product, accessories and packaging parts out of reach of children, to prevent accidents and choking hazards.
6. Always keep the product dry to avoid corrosion .
7. Do not use the product if you feel obvious discomfort, irritation or have other adverse reactions.
8. Do not expose the product to extreme temperatures below -15°C (5°F) or above 55°C (131°F) , to maintain the lifespan of headset or battery.

Delivery includes
Bluetooth headset 1pc
USB charging cable 1pc
User manual 1pc

Charging and battery
Only use charging cable supplied by Bluedio, or may cause damage to the headset.

Warning
The DC voltage should be 5V and current should exceed 400mA. Charging The headset built-in battery is rechargeable and non-detachable. Do not replace the battery.

1. Switch off the headset before charging.
2. Connect the smaller plug of the charging cable to the USB socket of the headset; connect the other plug to the USB socket of your computer or other charging device; the LED lights up red and the headset is being charged.
3. When the headset is fully charged(about 1.5-2hrs), the LED lights up blue or LED goes out .

Headset Overview

Pairing mode
Keep the MF button pressed until the LED remains blue.

Reconnection mode
Keep the MF button pressed until the LED flashes blue.

Switch the headset off
Keep the MF Button pressed until the LED flashes blue then goes off.

Pair the headset with your mobile phone

1. Keep the distance between the headset and your mobile phone ( or other Bluetooth device) within 1 meter. The closer, the better.
2. Keep the MF button pressed until the LED remains blue. the headset is in pairing mode.
3. Switch on the Bluetooth function of your mobile phone, on which start a search for Bluetooth devices.
4. From the found Bluetooth devices, select “Bluedio” to establish a Bluetooth connection to the headset. If necessary, enter thedefault PIN code “0000”.
5. Once the headset is paired with the mobile phone, the LED flashes blue.

Attention.
If pairing is not successful within 60 seconds, the LED goes off and the Bluetooth pairing ends. Repeat the pairing procedure.

Disconnect the headset with your mobile phone

1. Switch the headset off.
2. Or switch off the Bluetooth function of your mobile phone.
3. Or take the headset from your mobile phone 20m (60ft) away or even farther

Reconnect the paired headset to your mobile phone

1. Keep the distance between the headset and your mobile phone( Pr other Bluetooth device) within 1 meter. The closer, the better.
2. Keep the MF button pressed until the LED flashes blue. The headset is in reconnection mode.
3. Switch on the Bluetooth function of your mobile phone. The headset will automatically reconnect to it.

Answer a call
Press the MF button once, or use your made phone to answer it

End a call
Press the MF button once. Or use your mobile phone to end it.

Reject a call
After hearing a beep, keep the MF button pressed for around 2 seconds or use your mobile phone to reject it.

Cloud function:
The headphones support Cloud service. Users can download the APP by scanning the OR code on the last page.

Wake up the cloud( installed the Cloud APP on your phone)
Connect the headset with your phone, then double-click the MF button to wake up the Cloud. Cloud service is on, you can enjoy smart Cloud service.

Micro-SD card mode:
1. Insert the Micro-SD card.
2. Switch the headset on, and it will enter into reconnection mode. Or connect the headset with your mobile phone via Bluetooth . 3.Keep the Wheel switch pressed until the LED lights up green. The headset will enter into the Micro-SD card mode.

• If the headset doesn’t connect with mobile phone via Bluetooth, it will not support Bluetooth conversation.
• The headset will enter into Micro-SD card mode in priority if there is a Micro-SD card inside it. Press the Mode button once to enter into FM mode.
• When the headset and your mobile phone are under Bluetooth connection, if there comes a call during the Micro-SD card mode, the headset will emit a ringtone and the LED flashes blue. After call the headset will go back to the Micro-SD card mode.

Switching the Micro-SD card mode off
Keep the Wheel switch pressed for about 4 seconds, the headset will go back to Bluetooth music mode(if the headset and your mobile phone are under Bluetooth connection).

FM mode

1. Switch the headset on, and it will enter into reconnection mode. Or connect the headset with your mobile phone via Bluetooth. 2. Keep the Wheel switch pressed until the LED lights up green. The headset will enter into the FM mode.
2. Press the FM scan button once to search for channels, and the LED blinks green.
3. It takes about 2 minutes to finish searching, after the LED lights up green , push the Wheel switch up or down to adjust channel.

*If the headset doesn’t connect with mobile phone via Bluetooth, it will not support Bluetooth function.

*The headset will enter into Micro-SD card mode in priority if there is a Micro-SD card inside the headset. Press the Mode button once to enter into FM mode.

*When the headset and your mobile phone are under Bluetooth connection, if there comes a call during the FM mode, the headset will emit a ringtone and the LED flashes blue. After call the headset will go back to FM mode.

Switching the FM mode off
Keep the Wheel switch pressed for about 4 seconds, the headset will go back to Bluetooth music mode(if the headset and your mobile phone are under Bluetooth connection).

Track control/ volume adjustment
Track play/pause: press the MF button once.(Bluetooth mode) Play/pause: press the Wheel switch once.(Micro-SD card/FM mode) Next track/channel: push up the Wheel switch Previous track/channel: push down the Wheel switch Volume up: keep pushing the Wheel switch up until reaching proper volume. Volume down: keep pushing the Wheel switch down until reaching proper volume .

Micro-SD card file transference
Connect the headset (with a Micro-SD card inside)with your PC via USB charging cable.

Mode Selection( Bluetooth/Micro-SD card/FM)
Bluetooth mode to Micro-SD card/FM mode: Stop Bluetooth music playing; keep the Wheel switch pressed until the LED lights up green. the headset will enter into Micro-SD card mode in priority if there is a Micro-SD card inside it)

Note:
‘Press the Mode button once to select Micro-SD card/ FM mode. In Micro-SD card mode, remove the Micro-SD card, the headset will enter into FM mode automatically. In the FM mode, insert the Micro-SD card, the headset will enter into Micro-SD card mode automatically. Such operations may cause damage to the headset)

FAQ

1. Headset cannot be paired to your mobile phone.
   Solution: Check if your mobile phone supports the HS or HF profile. Check if the Bluetooth search function of your phone is switched on. Check if your mobile phone is switched off. Check if the distance between the headset and your phone exceeds loon.

2. Headset cannot be switched on.
   Solution: The battery is fiat. Recharge the battery.

3. Can the battery be replaced?
   Answer: The battery is non-detachable and cannot be replaced.

4. Can the headset be used while driving?
   Answer: Do not use the headset in an environment that requires your special attention. If necessary. use it for communication.

5. Bluetooth connection is suddenly interrupted within 10 meter.
   Solution: Chas* if there is metal or other material interfering with the transmission.

6. No audio signal
   Solution: Check if the headset is switched off. Check if the headset is paired. If necessary, pair the headset with the audio source again. Check the connection to your audio source. The volume is adjusted too low, increase the volume.

7. Can the headset be used to control the APPS on your mobile phone.
   Answer: Software settings of APPS may be varied , thus some APPS may not controlled by the headset.

8. The headset cannot be recharged.
   Solution: Check the connection of USB plugs. If necessary, remove the USB cable and reconnect again. Switch the headset on then turn it off.

Technical specification:
Driver units: 2 speakers(57mm)
Transducer type: dynamic
Bluetooth version: V5.0
Operating distance: up to 10m (free space)
Profiles: A2DP, AVRCP, HSP, HFP
Speaker impendence: 160
Frequency response: 20-20KHz
Sensitivity: 110dB
THD: <0.1% Supported
Micro-SD card capacity: up to 32 GB
Micro-SD card play time: about 15hrs
FM playtime: about 15his
Bluetooth music time: about 40hrs
Talk time: about 45hrs
Standby time: about 1625hrs(around 50days)
Fully charged time: about 2hrs
Operating environment: -10°C to 50°C

Technical specifications are subject to change without notice, we apologize for any inconvenience.

Questions about your Manual ? Post in the comments!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>