fortum 4770840 Tile Cutter User Manual

: June 3, 2024
: fortum

Table of Contents

fortum 4770840 Tile Cutter
Introduction
Technical specifications
Preparing the tile cutter for use
Scoring the tile
Snapping the tile
Storage of the laser source
Disposal of the laser source
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

fortum 4770840 Tile Cutter

fortum-4770840-Tile-Cutter-User-Manual-PRODUCT

Introduction

fortum-4770840-Tile-Cutter-User-Ma

Dear customer,
Thank you for the confidence you have shown in us by purchasing this product. This product has been tested for reliability, safety, and quality according to the prescribed norms and regulations of the European Union. Contact our customer and consulting center for any questions at: www.fortum.cz [email protected]
Manufacturer: Madal Bal a. s., Průmyslová zóna Příluky 244, 76001 Zlín, Czech Republic. Date of issue: 12. 5. 2020

Technical specifications

fortum-4770840-Tile-Cutter-User-Manual-
FIG-2

Preparing the tile cutter for use

Setup the tile cutter according to fig. 1. Secure both side bars with scales in place. For cutting larger tiles, tilt out the side support bar as shown in fig. 2 and secure it in place so that the tile is supported by this support to prevent it from damage while snapping it off.
There is a sliding „corner“ on the side bar that serves to secure the corner of the tile in place when making diagonal cuts, see fig. 4. To perform other types of cuts, it is not necessary to remove the sliding „corner“, simply slide it to such a distance so that it provides the tile with stability while the cut is made (see fig. 3), whilst proper-ly securing it using bolts against accidental movement.
A laser (fig. 5a) can be purchased as an optional acces-sory, that is mounted on the front part of the tile cutter using two screws (fig. 5b), that projects the cut line (fig. 5c). The laser is not included, but can be purchased under the part number 4770840A and it can also be used as an accessory for all tile cutters of this model line. The laser is powered using two type AAA, 1.5V batteries. The laser is turned on and off using a button.
The tile cutter comes with a lubricating oil tank with a manual pump. Sewing machine oil can be poured into the tank and pressing the pump button several times will lubricate the mechanism of the tile cutter. For the manual pump to function properly, it is necessary for the oil in the tank to be kept filled above half the volu-me of the tank.

Scoring the tile

Place the tile on the plate of the cutter with the glazed surface facing upwards utilising the guide to achieve the required position of the cut. If the cutter is fitted with an additional laser, turn it on to mark out the cut line (fig. 5c). Gently hold down the tile with one hand and use the other hand to drag the lever handle to ride the cutting wheel over the full length of the glazed surface of the tile there and back again (fig. 7).
Notes:
The function of the cutting wheel is only to score the glazed surface and not to cut through the tile.
The maximum tile cutting thickness is 18 mm and the minimum width is 35 mm.
The cutter can also be used to cut frost-resistant paving tiles, with the exception of paving tiles that have stones on the surface or other similar surfaces.

Snapping the tile

Place the snapping head of the cutter on to the edge of the tile as close to the guide as possible (fig. 8), i.e. to the position of the snapping ridge with the rubbe-rised surface, and make sure that the tile is freely positioned on the snapping ridge of the cutter with the glazed surface on top and that there are no unde-sirable items underneath the tile, e.g. tile fragments, etc. The snapping ridge of the cutter underneath the tile must be in alignment with the cut line on its glazed surface.

Using the handle, gently start pushing the snapping head down on the tile, gradually applying increasing pressure in order to achieve the minimum force necessa-ry for snapping the tile into two parts along the cut line.

ATTENTION

Prevent the cutting wheel from coming into contact with the tile when snapping it as this could cause the tile to crack in an undesirable manner.

Safety instructions for the laser source

Prevent small children, physically and mentally unfit persons and uninstructed persons from using the devi-ce. Ensure that children do not play with the device.
Do not remove the technical rating label from the device.
Never look into a laser beam. This could result in damage to eye sight. In the event that a laser beam enters your eye, immediately close your eye and move your head out of the line of the laser beam. It is not possible to use standard eye protection aids such as for example sun glasses with UV filters for protection against the laser. Never view the beam with optical devices.
Never point the laser beam at people, animals or at yourself.
Do not use the device in an environment with an explosion or fire hazard, where there are flammable materials, flammable gases or dust.
Do not disassemble the device and do not modify it in any way.
Do not point the beam at reflective surfaces. The beam could be deflected and hit the eyes of people.
When not using it, turn the laser off. This could result in eyes being hit.
Do not place the device near data storage devices, pacemakers and devices sensitive to magnetic fields. A magnetic field could result in the loss of data, endanger the life of a user with a pacemaker damage sensitive devices.
The laser source is sensitive equipment, so protect it against impacts and rough handling. Protect the laser beam outlet window against breakage.

MEANINGS OF THE MARKINGS ON THE LABEL OF THE LASER SOURCE

Storage of the laser source

Store the cleaned device in a safe, dry location that is out of reach of children and protect it against direct sunlight, radiant heat sources, frost, high humidity and ingression of water. Prior to storing the device, take out its batteries.

Disposal of the laser source

Throw packaging into the appropriate sorted waste container.
An unusable laser device is electrical equipment that must not be thrown out with household waste, but rather according to the European Directive (EU) 2012/19, it must be handed over for ecological disposal/ recycling at an appropriate electrical waste collection point.
Prior to handing over the device for disposal, the batte-ries must be removed, which, likewise, must not be thrown out with household waste, but rather must be handed over separately for ecological dispo- sal at a battery collection point. You will receive information about electrical equip- ment collection points at your local town council office.