Modules TGW206-16 Module User Manual

Modules TGW206-16 Module

DISCLAIMER AND COPYRIGHT NOTICE

Information in this document, including URL references, is subject to change without notice. This document is provided “As if” with no whatsoever, including any warranty of merchantability, noninfringement, fitness for any purpose, or any warranty otherwise arising out of any proposal, specification or samples. All liability, including liability for infringement of any proprietary rights, relating to use of information in this document is disclaimed. No licenses express or implied, by estoppel or otherwise, to any intellectual property rights are granted herein. The Bluetooth logo and symbol belong to the Bluetooth SIG Inc. The Wi-Fi Alliance Member Logo is a trademark of the Wi-Fi Alliance.
All trade names, trademarks and registered trademarks mentioned in this document are property of their respective owners, and are hereby acknowledged. Copyright ITON Technology Corp. All rights reserved.

summary

function
Product characteristics

• 802.11b/g/n，Wi-Fi+Bluetooth LE5. 0 combo, supports STA, soft AP and sniffer
•  Open source self controllable risc-v CPU, 1-160mhz adjustable, 276KB SRAM
•  Ultra low power consumption: sleep power consumption is only 0.5ua, networking standby power consumption is only 40ua (dtim10)
•  Super fast connection: cold start fast connection only 70ms
• Ultra long distance: maximum transmission power 15.05dBm, sensitivity – 98dbm, more than one wall
•  High security: support safe startup, safe debugging, AES 128 / 192 / 256 encryption engine, WPA3, MD5, SHA-1 / 224 / 256, PKA (RSA / ECC) encryption engine
•  Support the coexistence of Wi Fi and Bluetooth

Application scenario

•  Intelligent lighting
•  Smart switch
•  Smart socket
•  Smart home appliances
•  Monitoring and remote control

describe
XJ-WB60 is an intelligent new generation of highly integrated Wi Fi and Bluetooth Le chip. The wireless subsystem includes 2.4G RF, Wi Fi 802.11b/g/n and ble baseband / MAC design. The microcontroller subsystem includes a low- power 32-bit RISC CPU, cache and memory. The power management unit provides flexible settings to realize low power consumption mode and supports multiple security functions.

Functional block diagram

Pin pin definition

ModulePIN Interface diagram

Pin pin definition

Description

1. The standard transparent firmware uses gpio3 (user communication serial port RXD) and gpio4 (user communication serial port TXD) as communication serial ports with MCU.
2. The module supports up to five PWM outputs, and only one GPIO port can be set for thePWM of the same group.
3. Module characteristics and specifications

WiFi RF specification

Ble RF specification

Module electrical parameters

Reference application and PCB layout

Application schematic reference

PCB layout reference

• Keep clearance at the module antenna
• The module is far away from strong interference sources
• The capacitance shall be increased at the power supply, and the wiring shall be short and thick
• The module can be pasted on the PCB board or welded on the PCB board with 2.0 rows of pins
• PCB can use on-board antenna or IPEX base to connect external antenna (as shown below). This version is on-board antenna
• Onboard antenna: R8 (0r) / R9 (NC)
• PEX sub external antenna: R8 (NC) / R9 (0r)
• The module layout is recommended as follows:

Reference PCB package

Package size

Recommended pads

Revision history

FCC Caution

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IMPORTANT NOTE
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01

List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular. 2.3 Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

Limited module procedures
Not applicable

Trace antenna designs
Not applicable

RF exposure considerations
To maintain compliance with FCC’s RF Exposure guidelines.

Antennas
This radio transmitter FCC ID: 2AXSO-XJ-WB60 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID: 2AXSO-XJ-WB60”

Information on test modes and additional testing requirements
Host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.

Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>