RANGEMASTER RDWT6012-I1E 60cm Integrated Dishwasher User Guide
- June 13, 2024
- RANGEmaster
Table of Contents
- RDWT6012-I1E 60cm Integrated Dishwasher
- Product Information
- Product Usage Instructions
- 1. Before You Start
- 2. Before Using Your Appliance
- 3. Overview
- 4. Control Panel
- 5. Looking after your Dishwasher
- 6. Troubleshooting
- 7. Installation
- 8. Circuit Diagram
- 9. Technical Data
- 10. Warranty/After Sales Service
RDWT6012-I1E 60cm Integrated Dishwasher
Product Information
Product Name: T60 Dishwasher
User Guide & Installation & Service
Instructions: U111340 – 01
For Use In: GB and IE only
After Sales Service: Applies to GB and IE
only
Manufacturer’s Website: www.rangemaster.co.uk/co- ordinatingcollection/dishwashing
Product Usage Instructions
1. Before You Start
At Time of Delivery:
-
Check packaging and dishwasher immediately for signs of
transport damage. If the dishwasher is damaged, DO NOT USE. Contact
your supplier or customer services. -
Please dispose of packaging materials properly.
About these Instructions:
-
Please read these instructions carefully before using this
dishwasher. The instructions contain important information which
will help you get the best out of the dishwasher and ensure safe
and proper installation, use, and maintenance. -
Keep this manual in a convenient place so you can always refer
to it for the safe and proper use of the dishwasher. -
If you sell the dishwasher, give it away, or leave it behind
when you move house, make sure you also pass this manual so that
the new owner can become familiar with the dishwasher and safety
warnings.
During Installation:
- Follow the installation instructions provided in this
manual.
During Normal Use:
- Follow the operating instructions provided in this manual.
If a Fault Occurs:
-
If the dishwasher malfunctions, turn off the water supply and
disconnect the plug from the wall socket. -
If you cannot solve the problem, contact one of our service
centres:- UK Service Centre Tel: 0844 847 6711
- Republic of Ireland Service Centre Tel: 051 302 333
-
Only authorized persons should make repairs.
-
If the supply cord is damaged, it must be replaced by the
manufacturer, service agents, or authorized persons.
2. Before Using Your Appliance
Refer to the detailed instructions provided in this manual for
information on how to properly use your dishwasher.
3. Overview
Refer to the detailed instructions provided in this manual for
an overview of the dishwasher’s features and components.
4. Control Panel
Refer to the detailed instructions provided in this manual for
information on how to use and navigate the control panel of your
dishwasher.
5. Looking after your Dishwasher
Refer to the detailed instructions provided in this manual for
tips on how to properly care for and maintain your dishwasher.
6. Troubleshooting
Refer to the detailed instructions provided in this manual for
troubleshooting tips and solutions for common issues that may arise
with your dishwasher.
7. Installation
Positioning the Dishwasher:
Follow the installation instructions provided in this manual to
properly position your dishwasher.
Drain Hose Connection:
Follow the installation instructions provided in this manual to
properly connect the drain hose of your dishwasher.
Electrical Connection:
Follow the installation instructions provided in this manual to
properly connect the electrical supply to your dishwasher.
8. Circuit Diagram
Refer to the circuit diagram provided in this manual for a
visual representation of the electrical connections and components
of your dishwasher.
9. Technical Data
Refer to the technical data provided in this manual for detailed
specifications and information about your dishwasher.
10. Warranty/After Sales Service
Contact our service centres for warranty and after-sales
service:
- UK Service Centre Tel: 0844 847 6711
- Republic of Ireland Service Centre Tel: 051 302 333
Note: The above information and instructions are based on
the text-extract from the user manual. For complete and accurate
guidance, please refer to the original user manual provided with
the product.
T60
Dishwasher
User Guide
& Installation & Service Instructions
U111340 – 01
Contents
1. Before You Start
1
At Time of Delivery
1
About these Instructions
1
During Installation
1
During Normal Use
1
If a Fault Occurs
2
Caring for the Environment
2
Recommendations
3
2. Before Using Your Appliance 4
3. Overview
9
4. Control panel
10
5. Looking after your Dishwasher 12
6. Troubleshooting
14
7. Installation
16
Positioning the Dishwasher
16
Drain Hose Connection
17
Electrical connection
17
8. Circuit Diagram
18
9. Technical Data
19
10. Warranty/After Sales Service 21
1. Before You Start
DocNo.800-0101 – Introduction
This dishwasher is for use in GB and IE only. After sales service applies to
GB and IE only.
IMPORTANT: For an electronic copy of this user manual please go to the
following address:
www.rangemaster.co.uk/co-ordinatingcollection/dishwashing
At Time of Delivery
Check packaging and dishwasher immediately for signs of transport damage. If
the dishwasher is damaged DO NOT USE. Contact your supplier or customer
services.
Please dispose of packaging materials properly.
About these Instructions
Please read these instructions carefully before using this dishwasher. The
instructions contain important information which will help you get the best
out of the dishwasher and ensure safe and proper installation, use and
maintenance.
Keep this manual in a convenient place so you can always refer to it for the
safe and proper use of the dishwasher.
If you sell the dishwasher, give it away, or leave it behind when you move
house, make sure you also pass this manual so that the new owner can become
familiar with the dishwasher and safety warnings.
During Installation
· Site the dishwasher and connect in accordance with the installation
instructions.
· DO NOT connect the dishwasher to the electricity supply while carrying out
the installation.
· Make sure that the wiring is properly earthed.
· The mains electricity supply must conform to national and local regulations
and the details shown on the dishwasher nameplate.
· DO NOT connect the dishwasher to the electricity supply with an extension
cable.
· DO NOT connect the dishwasher to a socket with multiple outlets.
· Built-under and built-in dishwashers should always be installed under a
continuous work surface attached to adjacent cupboards. This will make sure
that the dishwasher is stable.
· After the dishwasher has been installed, the mains plug should be easily
accessible.
· DO NOT excessively bend or flatten the power supply cord during
installation. The dishwasher should not stand on the power supply cord.
· The water pressure should be between 0.03 Mpa and 1Mpa. Pressures above 1Mpa
will require a pressure relief valve to be fitted.
During Normal Use
· Following installation the first wash cycle must be with the dishwasher
unloaded.
· Commercial use of the dishwasher will void the guarantee.
· The dishwasher must only be used for washing household dishes and cooking
utensils.
· This dishwasher cannot be installed outdoors.
· DO NOT place heavy objects on the door or stand on it when it is open. The
dishwasher may tip forward.
· The water inside the dishwasher is NOT suitable for drinking.
· DO NOT use solvents of any kind inside your dishwasher. They could cause an
explosion.
1
· Use only detergent and rinse aid specifically designed for use in domestic
dishwashers.
· The suitability of plastic items must be checked before placing them in the
dishwasher.
· DO NOT place items in the dishwasher that are not suitable for dishwashing.
· DO NOT overfill the dishwasher baskets. This may result in basket movement
and damage the dishwasher.
· We do not recommend that the door is opened during operation. However, the
dishwasher door is fitted with a safety device that stops the dishwasher if
the door is opened during operation. As hot water may escape the dishwasher,
DO NOT open the door fully until the spray arms have stopped rotating. Also,
be careful of hot water escape at the base of the door.
· The dishwasher door should not be left open. Failure to close the dishwasher
door may lead to accidents.
· Sharp ended objects and knives should be placed into the cutlery basket with
the blade or sharp end facing down toward the base of the dishwasher.
· Never touch the dishwasher with wet hands.
· If the dishwasher is not operating properly or maintenance is required,
disconnect from the power supply.
· This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
· Keep detergents out of reach of children.
· When unpacking the dishwasher make sure that the packaging material is out
of reach of children.
· Keep children away from the dishwasher when the door is open.
· Keep children away from detergents and rinse aid.
· DO NOT allow children to play with or start the dishwasher.
If a Fault Occurs
If the dishwasher malfunctions, turn off the water supply and disconnect the
plug from the wall socket. If you cannot solve the problem, contact one of our
service centres on the below numbers:
UK Service Centre Tel: 0844 847 6711. Republic of Ireland Service Centre Tel:
051 302 333
Only authorized persons should make repairs.
If the supply cord is damaged it must be replaced by the manufacturer, service
agents or authorized persons.
To maintain the efficiency and safety of this dishwasher we recommend:
· Call only Service Centres authorized by the manufacturer.
· Always use original spare parts.
Caring for the Environment
Disposing of Your Packaging
Your new dishwasher was protected by suitable packaging while on its way to
you. All of the materials used are environmentally friendly for disposal and
can be recycled. Please make a contribution to protecting the environment by
disposing of the packaging appropriately.
2
Disposing of Your Old Dishwasher
Old dishwashers still have some residual value. An environmentally friendly method of disposal will make sure that valuable raw materials can be recovered and used again.
When your dishwasher has reached the end of its working life unplug it from the mains. Cut off the mains cable and dispose of it together with the plug.
Destroy the door locking mechanism so that children and pets cannot accidentally lock themselves in.
ArtNo.000-0019 Do not bin logo
This symbol on the product or its packaging indicates that the product may not be treated as household waste. Instead it should be handed over to your local community waste collection/recycling centre.
By disposing of this product correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused.
For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.
Recommendations
Removing coarse residue from items before placing them into the dishwasher
will save energy and water.
Try only to use your dishwasher when it is fully loaded.
Use the pre-wash program only whenever necessary.
Place hollow items such as bowls, glasses and pots face down into the
dishwasher.
DO NOT overload your dishwasher.
3
2. Before Using Your Appliance
Preparing your Dishwasher for first use
· Make sure the electricity and supply water specifications match the values
indicated in the installation instructions for the machine.
· Remove all packaging material inside the machine.
Test Strip
Run water through the tap (1min.)
Keep the strip in the water (1sec)
· Set the water softener level.
· Fill the rinse aid compartment.
Shake the strip.
Wait (1min.)
Set the hardness
level of your machine.
1
2
Fill the salt (IF AVAILABLE)
3
To add softener salt, open the salt compartment cap by
4
turning it counter clockwise. (1) (2) At first use, fill the
compartment with 1 kg salt and water (3) until it is almost overflowing. If available, using a funnel (4) will make filling
5
easier. Replace the cap and close it. After every 20-30 Cycles
add salt into your machine until it fills up (approx. 1 kg).
6
1
2
NOTE: The level is set to 3 as default. If the water is well water or has a
hardness level above 90 dF, we recommend that you use filter and refinement
devices.
Water Hardness Table
3
4
SALT
Only add water to the salt compartment on first use.
Use softener salt specifically produced for use in dishwashers.
When you start your dishwasher, the salt compartment is filled with water,
therefore put the softener salt in prior to starting your machine.
If the softener salt has overflowed and you do not start the machine
immediately, run a short washing program to protect your machine against
corrosion.
Level
German dH
French dF
British dE
1
0-5
0-9
0-6
2
6-11
10-20 7-14
3
12-17 21-30 15-21
4
18-22 31-40 22-28
5
23-31 41-55 29-39
6
32-50 56-90 40-63
Indicator
L1 is shown on the display. L2 is shown on the display. L3 is shown on the
display. L4 is shown on the display. L5 is shown on the display. L6 is shown
on the display.
Water Softener System
The dishwasher is equipped with a water softener which reduces the hardness in
the mains water supply. To find out the hardness level of your tap water,
contact your water company or use a test strip (if available).
Setting
Push the programme button and hold it down. Turn on the machine. Hold down the
programme button until “SL” disappears. The machine will display the last
setting. Set the level by pushing the programme button. Switch off the machine
to save the setting.
4
Detergent usage
Only use detergents specifically designed for domestic dishwashers. Add the
recommended amount of detergent for the selected programme to ensure the best
performance. Keep your detergents in cool, dry places out of reach of
children. See the detergent manufacturer’s instructions for further
information.
Filling the detergent
Push the latch to open the dispenser and pour in the detergent. Close the lid
and press it until it locks in place. The dispenser should be refilled just
before the start of each programme. If the dishes are heavily soiled, place
additional detergent in the pre-wash detergent chamber.
DETERGENT
Rinse-aid usage
Rinse-aid makes dishes sparkle and helps them to dry without spotting. Rinse-
aid is required for stain-free utensils and clear glasses. Use only rinse-aid
for domestic dishwashers.
Filling the rinse-aid and setting
To fill the rinse aid compartment, open the rinse-aid compartment cap. Fill
the compartment with rinse aid to the MAX level and then close the cap. Be
careful not to overfill the rinse aid compartment and wipe up any spills.
In order to change the rinse aid level, follow the below steps before turning
on the machine:
Push the programme button and hold it down.
Turn on the machine.
Hold down the programme button until “rA” disappears from the display. Rinse
aid set follows water hardness set.
The machine will display the current setting.
Change level by pushing the programme button.
Switch off the machine to save the setting.
The factory setting is “4”.
If the dishes are not drying properly or are spotted, increase the level. If
blue stains form on your dishes, decrease the level.
Using combined detergents
These products should be used according to the manufacturer’s instructions.
Never put combined detergents into the interior section or the cutlery basket.
Combined detergents contain not only the detergent but also rinse-aid, salt
replacement substances and additional components depending on the combination.
We recommend you do not use combined detergents in short programmes. Please
use powder detergents in such programmes.
If you encounter problems when using combined detergents, please contact the
detergent manufacturer.
When you stop using combined detergents, make sure that water hardness and
rinse aid settings are set to correct level.
Level 1 2 3 4 5
Brightener Dose Rinse-aid not dispensed
1 dose is dispensed 2 doses are dispensed 3 doses are dispensed 4 doses are
dispensed
Indicator r1 is shown on the display. r2 is shown on the display. r3 is shown on the display. r4 is shown on the display. r5 is shown on the display.
5
Loading your dishwasher
For best results, follow these loading guidelines.
Loading the household dishwasher up to the capacity indicated by the
manufacturer will contribute to energy and water savings.
Manual pre-rinsing of tableware items leads to increased water and energy
consumption and is not recommended. You can place cups, glasses, stemware,
small plates, bowls, etc. in the upper basket.
Do not lean long glasses against one another as they may become damaged.
When placing long stem glasses and goblets, lean them against the basket edge
or rack and not against other items.
Place all containers such as cups, glasses and pots in the dishwasher with the
opening facing downwards otherwise water can collect on items.
If there is a cutlery basket, you are recommended to use the cutlery grid in
order to obtain the best result.
Place all large (pots, pans, lids, plates, bowls etc.) and very dirty items in
the lower rack.
Dishes and cutlery should not be placed above each other.
n WARNING: Take care not to obstruct the rotation of spray arms.
n WARNING: Make sure after loading the dishes do not prevent opening the
detergent dispenser.
Upper Basket
Height adjustment
Turn the Rail Stop Clips, at the ends of the rails, to the sides to open them
(as shown in the image below), then pull out and remove the basket. Change the
position of the wheels, then reinstall the basket to the rail, making sure to
close the Rail Stop Clips.
When the upper basket is in the higher position, large items such as pans can
be placed on the lower basket.
Recommendations
Remove any coarse residue on dishes before placing the dishes in the machine.
Start the machine with full load.
n Do not overload the drawers or place dishes in the wrong basket.
n WARNING: To avoid any possible injiuries, place long-handle and sharp-
pointed knives with their sharp points facing down or horizontally on the
baskets.
Alternative basket loads
Lower basket
6
Upper basket Incorrect loads
n IMPORTANT: In future, purchase dishwasher-proof kitchenware.
Incorrect Loads
Incorrect loading can cause poor washing and drying performance. Please follow
the manufacturer’s recommendations for a good performans result.
Unsuitable items for dishwashing Cigarette ashes, candle left overs, polish,
paint, chemical substances, iron alloy materials. Forks, spoons and knives
with wooden, bone, ivory or nacre coated handles; glued items, items soiled
with abrasive, acidic or base chemicals. Temperature-sensitive plastics,
copper or tin coated containers. Aluminium and silver objects. Some delicate
glasses, ornamental printed porcelains; some crystal items, adhered cutlery,
lead crystal glasses, cutting boards, synthetic fibre items. Absorbent items
such as sponges or kitchen rugs.
7
Programme table
P1
P2
P3
Programme name
Eco
Intensive 65°C
Auto
Hygiene 70°C
Type of Soil:
Standard program for
normally soiled daily dishes with
reduced energy and water consumption
Suitable for heavily soiled dishes
Auto program for heavily soiled dishes
Suitable for heavily soiled dishes requiring hygienic washing
Level of Soil: Medium
Heavy
Heavy
Heavy
Amount of
detergent:
A
A
A
A
A 25 cm3
B 15 cm3″
Program duration (h/min)
03.25
01:57
01:25 – 01:57
02:07
Electricity consumption (kWh/cycle)
0.923
1.700
1.450 – 1.700
1.900
Water
consumption
12.0
(L/cycle)
17.2
11.9 17.2
16.0
P4 Super 50′
Suitable for normally soiled daily dishes with faster program
Medium
A
00:50
1.100
12.0
P5 Quick 30′
P6 Prewash
Suitable for lightly soiled dishes and quick wash
Suitable to rinse dishes that you plan to wash later.
Light A
Light –
00:30 0.740 12.4
00:15 0.020
4.5
· The program duration may change according to the amount of dishes, the water
temperature, the ambient temperature and selected additional functions.
· Values given for programmes other than the eco programme are indicative
only.
· Eco programme is suitable to clean normally soiled tableware, that for this
use, it is the most efficient programme in terms of its combined energy and
water consumption, and that it is used to assess compliance with the EU
ecodesign legislation.
· Washing tableware in a household dishwasher usually consumes less energy and
water in the use phase than hand dishwashing when the household dishwasher is
used according to the manufacturer’s instructions.
· Only use powder detergent for short programs.
· Short programs do not include drying.
· To assist drying, we recommend slightly opening the door after a cycle is
complete.
· You can access the product database where the model information is stored by
reading the QR code on the energy label.
Note: According to regulations 1016/2010 and 1059/2010, Eco program energy
consumption values may differ. This table is in line with regulations
2019/2022 and 2017/2022.
8
3. Overview
Fig. 3.1
A Upper basket with racks
A
B
B Upper basket track latch
C
C Upper spray arm
D Lower basket
D
E Cutlery basket
E
F Control panel
G Lower spray arm
H Salt dispenser
F
I Washing filter
J
Detergent and rinse aid dispenser
K Rating plate
L Water inlet hose
M Drain hose
N Power supply cord
O Active drying unit
DocNo.800-0203 – Overview – RDW459 diswasher
L M N G H I J
K
O
9
4. Control panel
3
12
4 5 67 8
1. On/Off Button
2. Programme Selection Button
3. Display
4. Delay Button
5. Half Load Button
6. Half Load LED
7. Salt Indicator
8. Rinse Aid Indicator
1. On/Off Touch Button Turn the machine on by pressing the On/Off button.
When the machine is on, “–” will be shown on the Display (3).
2. Programme Touch Button Select a suitable programme for your dishes by
touching programme selection button (2). The programme will start
automatically when the door is closed.
3. Display The display shows the number and total time of the selected
programme, alternately, and the remaining time during operation.
4. Delay Buttton Press the delay button to delay the start time of the
selected programme from 1 hour up to 19 hours. Pressing the button once delays
the start time for 1 hour, continuing to press will increase the delay time.
Press the Delay button to change or cancel the delayed start. If you switch
off the machine while delay timer is active, the delayed time is cancelled.
5. Half Load Button Press the half load button to reduce the duration of the
selected programme, and therefore decrease your energy and water consumption.
When the half load option is selected, half load LED (6) will illuminate.
NOTE: If you decide not to start the selected programme, please see the
“Changing a Programme” and “Cancelling a Programme” sections. NOTE: When there
is insufficient softening salt, the Salt Warning Indicator (7) will illuminate
to indicate the salt chamber needs filling. NOTE: When there is insufficient
rinse aid, the Rinse Aid Warning Indicator (8) will illuminate to indicate the
rins chamber needs filling.
Changing a Programme
Follow the steps below to change a programme while in operation.
2
1. Open the door and press the Programme selection button (2) to select a new
programme.
2. After closing the door, the newly selected programme will resume the
course of the old programme.
NOTE: Open the door slightly at first to stop a wash programme before it is
complete in order to avoid water spillage.
10
Cancelling a Programme
Follow the steps below to cancel a programme while in operation.
1. Open the door of the machine, the selected programme will be shown on the
display.
2. Press and hold the Programme selection button (2) for 3 seconds. At the
end of 3 seconds, `1′ will show on the Display (3).
3. The water discharge process will start after the door of the machine is
closed and will continue for 30 seconds. When the programme is cancelled, a
buzzer will sound 5 times.
Switching the Machine Off
“00” will be shown on the display when the selected wash programme is
complete, a buzzer will also sound 5 times. You can then switch your machine
off using the Power On/Off button (1).
NOTE: Do not open the door before a programme is complete.
NOTE: If the door of the machine is opened or the power is cut during
operation, the programme will continue when the door is closed or the power
returns.
NOTE: If the power is cut or the machine door is opened during the drying
process, the programme will terminate. Your machine will now be ready for a
new programme selection.
Buzzer Sound Control
To change the buzzer sound level, follow the below steps:
1. Open the door and press the Programme (2) and Delay (4) buttons
simultaneously for 3 seconds.
2. When the sound setting is recognised, the buzzer gives a long sound and
the machine will display the last set level, from “S0” to “S3″.
3. To decrease the sound level press the Programme button (2). To increase
the sound level, press the Delay button (4).
4. To save the selected sound level, turn off the machine.
”S0” level means all voices are off. Factory setting is “S3”.
Power Save Mode
To activate or deactivate power save mode, follow the below steps:
1. Open the door and press the Delay (4) and Half Load (5) buttons
simultaneously for 3 seconds.
2. After 3 seconds, the machine will display last Setting, “IL1” or “IL0”.
3. When Power Save Mode is activated, “IL1” will be displayed. On this mode,
interior lights will turn off 4 minutes after the door is opened, and the
machine will turn off after 15 minutes of no activity in order to save energy.
4. When Power Save Mode is deactivated “IL0” will be displayed. If Power Save
Mode is deactive, interior lights will be on as long as the door is open, and
the machine will always be on unless it is turned off by user.
5. To save the selected setting, turn off the machine.
In factory setting, Power Save Mode is active.
Info. LED (Model Dependent)
LED Indicator Red, continuous
Red, flashing
State of the Machine The machine is running a
program. A program is cancelled.
Red, flashing rapidly
The machine has a fault. Refer to section “Automatic fault warnings and what to do”.
Green, continuous
Program has finished.
11
5. Looking after your Dishwasher
Fig. 5.1
Fig. 5.2
a
Cleaning your dishwasher is important to maintain the machine’s service life
Make sure that the water softening setting (If available) is done correctly
and correct amount of detergent is used to prevent limescale accumulation.
Refill the salt compartment when the salt sensor light comes on.
Oil and lime may build up in your Dishwasher over time. If this occurs:
· Fill the detergent compartment but do not load any dishes. Select a
programme which runs at high temperature and run the Dishwasher empty. If this
does not clean your Dishwasher sufficiently, use a cleaning agent designed for
use with dishwashers.
· To extend the life of your dishwasher, clean the appliance regularly; once a
month.
· Wipe the door seals regularly with a damp cloth to remove any accumulated
residue.
b
Fig. 5.3
Filters
Clean the filters and spray arms at least once a week. If any food waste
remains on the coarse and fine filters, remove them and clean them thoroughly
with water.
a. Micro Filter b. Coarse Filter c. Metal Filter · To remove and clean the
Micro/Coarse filter combination, turn it counter clockwise and take it out by
lifting upwards (Fig. 5.1 and Fig. 5.2).
· Pull and remove the metal filter (Fig. 5.3).
· Rinse the filters with lots of water until they are free of residue.
· Refit the metal filter.
· Insert the Micro/Coarse filter and rotate it clockwise (Fig. 5.4).
c
Fig. 5.4
12
Cleaning
Drain Pump
Large food residues or foreign objects which were not captured by the filters
may block the waste water pump. The rinsing water will then be above the
filter.
n Warning Risk of cuts!
When cleaning the waste water pump, ensure that you do not injure yourself on
pieces of broken glass or pointed implements.
1. First, always disconnect the appliance, from the power supply.
2. Take out baskets.
3. Remove the filters.
4. Scoop out water, use a sponge if required.
5. Check the area and remove any foreign objects.
6. Install filters.
7. Re-insert baskets.
Spray arms (Fig. 5.5)
Make sure that the spray holes are not clogged and that no food waste is stuck
to the spray arms. If there is any clogging, remove the spray arms and clean
them under water.
To remove the upper spray arm undo the nut holding it in position, by turning
it clockwise, and pulling it downwards. Make sure that the nut is properly
tightened when refitting the upper spray arm.
Fig. 5.5
13
6. Troubleshooting
DocNo.800-0401 – Troubleshooting – RDW6012 dishwasher
FAULT
The programme does not start.
Water remains inside the machine.
Machine stops during washing. Shaking and hitting noises are heard during a
wash operation.
Partial food wastes remain on the dishes.
Whitish stains remains on dishes.
Dishes do not dry.
Rust stains form on the dishes.
Detergent remains in the detergent compartment.
POSSIBLE CAUSE
Your Dishwasher is not plugged in. Your Dishwasher is not switched on.
Fuse blown. Water inlet tap is closed. Your Dishwasher door is open.
Water inlet hose and machine filters are clogged.
Water drain hose is clogged or twisted. The filters are clogged.
The programme is not finished yet. Power failure.
Water inlet failure.
The spray arm is hitting the dishes in the lower basket.
Dishes placed incorrectly, sprayed water not reaching affected dishes.
Dishes leaning on each another.
Not enough detergent used.
Wrong wash programme selected.
Spray arms clogged with food waste. Filters or water drain pump clogged or
filter misplaced.
Not enough detergent used.
Rinse aid dosage and/or water softener setting set too low.
High water hardness level. Salt compartment cap not closed properly.
Drying option is not selected. Rinse aid dosage set too low. Stainless-steel
quality of the dishes is insufficient.
High level of salt in wash water.
Salt compartment cap not closed properly. Too much salt spilled in the
Dishwasher while filling it with
salt. A poor mains grounding. Detergent was added when the detergent
compartment
was wet.
TROUBLESHOOTING
Plug your Dishwasher in. Switch your Dishwasher on by pressing the On/Off
button.
Check your indoor fuses. Turn on the water inlet tap. Close the Dishwasher
door. Check the water inlet hose and machine filters and make sure they are
not clogged. Check the drain hose, then either clean or untwist it.
Clean the filters. Wait until the programme is finished.
Check mains power. Check water tap.
Move or remove items blocking the spray arm.
Do not overload baskets.
Place dishes as instructed in the section on loading your dishwasher.
Use the correct amount of detergent, as instructed in the programme table.
Use the information in the programme table to select the most appropriate
programme.
Clean the holes in the spray arms with thin objects. Check the drain hose and
filters are correctly fitted. Use the correct amount of detergent, as
instructed in the
programme table.
Increase rinse aid and/or water softener level.
Increase water softerner level and add salt. Check that the salt compartment
cap is closed properly.
Select a programme with a drying option. Increase rinse aid dosage setting.
Use only dishwasher-proof sets.
Adjust the water hardness level using water hardness table.
Check that the salt compartment cap is closed properly. Use funnel while
filling salt to the compartment to avoid
spillage. Consult a qualified electrician immediately.
Make sure detergent compartment is dry before use.
14
Automatic fault warnings and what to do
ERROR CODE
FF
F5 F3
F2
F8 F1 FE F7 F6 F9 HI LO
POSSIBLE FAULT
Water inlet system failure
Pressure system failure Continuous water input
Inability to discharge water
Heater error Overflow
Faulty electronic card Overheating error Faulty heater sensor
Divisor position error High voltage failure Low voltage failure
WHAT TO DO
Make sure the water inlet tap is open and water is flowing. Separate the inlet
hose from the tap and clean the filter of
the hose. Contact for service if the error continues.
Contact for service. Close the tap and contact for service. Water discharge
hose and filters may be clogged.
Cancel the program. If the error continues, contact for service.
Contact for service. Unplug the machine and close the tap.
Contact for service. Contact for service. Contact for service. Contact for
service. Contact for service. Contact for service. Contact for service.
The installation and repair procedures should always be carried out by the
Authorised Service Agent, in order to avoid possible risks. The manufacturer
shall not be held liable for damages that may arise from procedures carried
out by unauthorised persons. Repairs may be carried out by technicians only.
If a component has to be replaced, ensure that only original spare parts are
used.
Improper repairs or use of non-original spare parts may cause considerable
damage and put the user at considerable risk.
Contact information for your customer service can be found on the back of this
document.
Function-relevant genuine spare parts according to the corresponding Ecodesign
order can be obtained from Customer Service for a period of at least 10 years
from the date on which your appliance was placed on the market within the
European Economic Area.
15
7. Installation
· DocNo.800-0503 – Installation – RDW459 dishwasher
This dishwasher is for use in GB and IE only. After sales service applies to GB and IE only.
Fig. 7.1
Positioning the Dishwasher
Read all warnings located on the packaging before removing the packaging and
positioning the machine.
n Do not install the dishwasher in a room where the temperature is likely to
fall below freezing (0 °C).
n Do not grip the door when moving the dishwasher.
When positioning the machine, place it in an area where dishes can be easily
loaded and unloaded.
The dishwasher should be aligned to the front of the adjacent cabinets, with
allowance made for the door thickness. Place the machine close to a water tap
and drain. Take into consideration that the connections will not be altered
once the machine is in position.
Before installing the dishwasher into a kitchen cabinet, holes must not be
drilled into the sides, or door, to avoid compromising the performance and
operation of the dishwasher.
A plastic self-adhesive anti-condensation strip is supplied with the
dishwasher. Fix the strip to the underside of the worktop, along the front
edge (Fig. 7.1).
Connect up the cold water supply, the drain hose and the electrical
connections (see below) then slide the dishwasher into the cabinet opening.
Leave an adequate distance around the machine to allow ease of movement when
cleaning.
n Ensure the water inlet and outlet hoses are not squeezed or trapped and that
the machine does not stand on the electrical cable while positioning.
Adjust the feet so the machine is level and balanced. The machine should be
placed on flat ground otherwise it will be unstable and the door of the
machine will not close properly.
Fig. 7.2
Note printing on the water inlet hose! If models are marked with 25° the water
temperature may be max. 25 °C (cold water). For all other models: Cold water
preferred; hot water max. temperature 60 °C.
Water connection (Fig. 7.2)
We recommend fitting a filter to your water inlet supply in order to prevent
damage to your machine due to contamination (sand, rust, etc.) from indoor
plumbing. This will also help prevent yellowing and deposit formation after
washing.
Water inlet hose
n WARNING: Use the new water inlet hose supplied with your machine, do not use
an old machine’s hose.
n WARNING: Run water through the new hose before connecting.
16
Fig. 7.3 Fig. 7.4
n WARNING: Connect the hose directly to the water inlet tap. The pressure
supplied by the tap should be a minimum of 0.03 MPa and a maximum of 1 MPa. If
the pressure exceeds 1 MPa, a pressure relief valve must be fitted between the
connection.
n WARNING: After the connections are made, turn the tap on fully and check for
water leaks. Always turn off the water inlet tap after a wash program has
finished (Fig. 7.3).
n An Aquastop water spout is available with some models. Do not damage it or
allow it to become kinked or twisted.
Drain Hose Connection
Connect the water drain hose directly to water drain hole or to the sink
outlet spigot. This connection should be minimum 50 cm and maximum 110 cm from
floor plane (Fig. 7.4).
n IMPORTANT: Items will not wash properly if a drain hose longer than 4m is
used.
Electrical connection
n WARNING: Your machine is set to operate at 220-240 V. If the mains voltage
supply to your machine is 110 V, connect a transformer of 110/220 V and 3000 W
between the electrical connection.
n The earthed plug of the machine must be connected to an earthed outlet
supplied by suitable voltage and current.
n In the absence of earthing installation, an authorised electrician should
carry out an earthing installation. In the case of use without earthing
installed, we will not be responsible for any loss of use that may occur.
n The indoor fuse current value should be 10-16 A. n The plug on this
appliance may incorporate a 13A
fuse depending on the target country (for example UK, Saudi Arabia).
17
8. Circuit Diagram
Code Description TS Turbidity sensor RI Rinseaid indicator SI Salt indicator FM Flow meter NTC NTC sensor DV Diverter IV Inlet valve FS Float sensor DP Drain pump TF Turbo fan PS Pressure switch RV Regeneration valve DS Door switch DE AC dispanser HE Heating element SF Heating safety
Code Description CP Circulation pump C Capasitor RW Rotary switch
BLDC BLDC pump PST Power supply terminal MS Main switch DUB Display and user
board U1X Display end user board U2X Display end user board U3X Display end
user board SFL Safety lock LM Light module PSW Pressue level switch WHS Water
hardness sensor CULCD Control unit LCD ATSW Automatic on off switch
Code Description
LCD Liquid crystal display
PFLT TRF ALL
Parasite filter
Transformer light module
Ambi light LED
AOD Automatic open door
TFT TFT LCD
FC Ferrit core
WRV Water recycling valve
WRP Water recycling pump
SC Silicon cable
HIP Heater integrated pump
Code Description or Orange wh White blu blu re Red br Brown pi Pink vi Violet
bl Black gr Green yl Yellow
yl / gr Yellow / Green gry Grey
18
9. Technical Data
INSTALLER: PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER. DATA BADGE LOCATION:
INSIDE FACE ON THE SIDE OF THE DOOR. COUNTRY OF DESTINATION: GB, IE.
Dimensions
598 570 min
820 – 870 max
600 min 820 – 870
647 – 717 max
All dAirmtNoe.8n00s-i0o1n28s-i4n5 mm dishwasher dimensions
550
Connections
ELECTRIC
Technical specifications
Capacity Dimensions: Height x Width xDepth Net weight Operating voltage /
frequency Total current Total power
Water supply pressure
220240 V 50 Hz
12 place settings 820-870 (mm) x 598 (mm) x 550 (mm)
31.5 kg 220-240V 50 (Hz)
10(A) 1900(W) Maximum: 1 (Mpa) Minimum: 0.03 (Mpa)
19
Ratings
Supplier’s trade mark
Rangemaster
Supplier’s model
RDW6012D22
Capacity of dishwasher
12
The energy efficiency class
A++
Annual energy consumption in kWh per year (AEc) ( 280 Cycle )*
258
Energy consumption (Et) (kWh per cycle)
0,90
Off-mode power consumption (W) (Po)
0,50
Left-on mode power consumption (W) (Pi)
1,00
Annual water consumption in litres per year (AWc) ( 280 Cycle )**
3360
Drying efficiency class***
A
Standard programme name****
Eco
Programme time for standard cycle ( min)
187
Duration of the left-on mode (Ti ) (min)
–
Airborne acoustical noise emissions ( dB(A) re 1 pW ) Freestanding/Built-in
49 Built-in
in* Energy consumption 258 kwh per year, based on 280 standard cleaning cycles using cold water fill and the consumption of low power modes. Actual energy consumption will depend on how the appliance is used.
** Water consumption 3360 litres per year based on 280 standard cleaning cycles. Actual water consumption will depend on how appliance is used.
*** Drying efficiency class A on a scale from G (least efficient) to A (most efficient).
**** The “Eco” is the standard cleaning cycle to which the information in the label and the fiche relates. This programme is suitable to clean normally soiled tableware and it is the most efficient programme in terms of combined energy and water consumption.
20
10. Warranty/After Sales Service
If consultation or technical assistance is needed, please provide the local
authorised service agent with the purchase invoice and the product code/serial
number.
The 2 years free maintenance for the operation of the appliance started from
the date of purchase of this product.
Any cosmetic damage to the appliance must be reported within 30 days of
delivery.
Please note that AGA Rangemaster Limited have appointed Pacifica to administer
in warranty repairs on our behalf. If you make a request for an in warranty
repair, your details will be held by Pacifica
Warranty Support Pacifica 0844 847 6711
DocNo.111-0003 Warranty No.10
21
NOTES 22
NOTES 23
·
DocNo.000-0001 – Back cover Rangemaster
Clarence Street, Royal Leamington Spa, Warwickshire, CV31 2AD, England.
Tel: +44 (0) 1926 457400 Fax: +44 (0) 1926 450526 E-mail:
consumers@rangemaster.co.uk
www.rangemaster.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>