LILIN 3782CSB-3 HD Dome IP Camera Installation Guide

LILIN 3782CSB-3 HD Dome IP Camera

Product Information

Specifications :

• Model: HD Dome IP Camera
• Dimensions: 48mm x 110mm
• Connectivity: M12 connector (supports PoE), RJ-45 Ethernet connector (supports PoE), DC Power Input
• Features: Alarm In/Out Terminal, Micro SD Card Slot, Factory default button, Network Indicator LEDs

Product Usage Instructions

Installation:

1. Retrieve the camera from the box and connect the Ethernet/M12 cable and DC power cable to the appropriate connectors.
2. Remove the bottom chassis from the dome cover, fix the camera in the desired location, and tighten the screws.
3. Adjust the camera angle by loosening and tightening the screws on the translucent cover.
4. Connect the RJ-45 Ethernet cable with a waterproof connector and attach the dome cover to the bottom chassis.

Configuring IP Addresses via Web Interface:
To change the IP address via web interface, access the default IP address (192.168.0.200) in your Internet browser and follow the provided steps.

System Architectures:
Choose one of the following system architectures for connecting the IP Camera series to the network:

1. Use DC12V power adaptor and network switch connected to a network.
2. Use PoE of the network switch connected to the network.

Software Requirements :
Universal ActiveX software components are required for web interface display of JPEG or Full HD video. Install the Universal ActiveX when prompted by the security warning dialog box in Internet Explorer.

Configuring IP Addresses with IPScan Software:

1. Run the IPScan software.
2. Click Refresh to list all available devices.
3. Select your device from the list and change the IP address, subnet mask, gateway, or HTTP port as needed.

FAQ

• Q: How do I reset the camera to factory settings?
  A: Locate the factory default button on the camera body and press it for a few seconds to reset the camera to its default settings.

HD DOME IP CAMERA
Installation Guide

Warning: Do not throw your product in municipal waste. This product has been designed to enable proper reuse of parts and recycling. The symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulation for disposal of electronics products

Part Description & Dimensions

1. M12 connector (supports PoE) [Used in M12 Model]
2. RJ-45 Ethernet connector (supports PoE) [Used in RJ-45 Model]
3. DC Power Input [Used in DC Jack]
4. Alarm In/Out Terminal
5. Bottom Chassis
6. Dome Cover
7. Mask Cover
8. Camera Body
9. Micro SD Card Slot
10. Factory default button
11. Network Indicator LEDs
12. Green(Link): Network connection. LED remains lit white connection is in place. Orange(ACT): Data communications. This LED should continue to blink. Microphone [Used in MIC function]

Installation

1.  Retrieve the camera from the box first. Connect the Ethernet/M12 cable and DC power cable to the camera’s RJ-45/M12 connector and DC power-in connector (FIG.1).
   Note: For outdoor installation, it is recommended to install a waterproof junction box (FIG.2).

2. Remove the bottom chassis from the dome cover with a torx wrench (FIG.3).
   Use the included screws (T4.0x19) through the holes marked as “a”, and fix the camera in the desired location (FIG.4&5).

3. Loose the screws on the translucent cover to rotate the camera body to the desired angle and then tighten the screw (FIG.6).

Connect the RJ-45 Ethernet cable with a waterproof connector[Used in RJ-45 Model] First, remove the waterproof connector and unscrew the waterproof nut. Insert the Ethernet cable and connect to the RJ-45 connector with proper tools (FIG.7). Then, tighten the waterproof connector and nut before the RJ-45 connector is connected to the camera (FIG.8).

Attach the dome cover to the bottom chassis. Use torx wrench to tighten the screws (FIG.9).

• During installation in a humid environment, leaving the transparent top cover open for an extended period of time may cause fogging.
• Do not remove the desiccant from its vacuum packaging for more than 5 minutes.
• Ensure that moisture does not come into contact with the desiccant. 【Angle adjustment → Desiccant → Transparent top cover】 The installation process should be completed within 10 minutes.

System Architectures

For connecting IP Camera series to the network, please follow one of the system architectures:

1. Use DC12V power adaptor and network switch connected to a network.
2. Use with PoE of the network switch connected to the network.
3. Use PoE power injector and the network switch connected to the network.

Before Accessing IP Cameras

• Before accessing the IP camera, make sure that the camera’s RJ-45 network, audio, and power cables are properly connected. To set the IP address, consult your network administrator for an available
• IP address. The default IP address for each IP camera is 192.168.0.200. Users can use the default IP address for verifying the camera’s network connection.

Emergency Factory Default

To restore the hardware to factory default settings, please follow these steps:

1. Press and hold “RESET Key” for 10 seconds and release.

2. Wait for about 40 seconds, and the network LED light should turn off, and go back on again.

3.  The camera is now restored to factory default settings, and will reboot automatically.

4.  Search for the IP device using the IPScan software.

5.  Start the IP device via an Internet browser.

6.  Enter the username and password to operate.

   • NOTE1
     The factory default username and password are empty, and the user can set an account for login

   • NOTE2:
     The IP address will revert to the default setting of 192.168.0.200

Configuring IP Addresses via Web Interface
To change an IP address via web interface, type the default IP address (192.168.0.200) in the Internet browser and follow the steps below:

1. Login to the Full HD IP camera with the set username and password.
2. Click Basic Mode configuration hyperlink.
3. Click Network->General hyperlink.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP camera.
5. Click Submit to verify the settings.

Software Requirements
Universal ActiveX software components are required for web interface display of JPEG or Full HD video. When you login to the IP camera by Internet Explorer, the security warning dialog box will prompt the installation of the Universal ActiveX. Click Install to download it.

Configuring IP Addresses with IPScan Software
To change the settings of the IP address, subnet mask, gateway, or HTTP port, you can follow the steps below:

1.  Run the IPScan software.
2. Click Refresh. All available devices should be listed in the device list.
3. Select your device from the list provided.
4.  Change the IP address, subnet mask, gateway, or HTTP port for the IP camera.
5. Click Apply to submit the settings.
6. Click Refresh to verify the settings.

Login

The factory default username and password are empty. To login to the Full HD IP camera, please set the username and password on the login page. Press [Login] to complete the setting and login simultaneously.

Password have to meet the following criteria:

1. More than or equal to 8 characters.
2. Allow uppercase letter, lowercase letter, number digit, and special character.
3. Must have at least three types of character sets.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>