Hunter 19715 Lochemeade Natural Black Iron with Smoked Glass 4 Light Instruction Manual
- June 1, 2024
- Hunter
Table of Contents
Hunter 19715 Lochemeade Natural Black Iron with Smoked Glass 4 Light
Lochemeade
For Models: 19714 19715 19720
Instructions
Tools
Here are the tools you’ll need to complete your installation:
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. It you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These Instructions are provided for your safety. It Is very important that
they are read carefully and completely before beginning Installation of the
lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Remove cap nuts (N) from mounting screws (A). Put the drywall anchor (H) inside the hole in the ceiling. Place the mounting plate (B) over the junction box so that mounting screws (A) and nuts (C) extend out away from the ceiling. Pull the house wires through the center of mounting plate (B). Secure mounting plate (B) to the junction box by tightening the screws (D), then insert the drywall screw (I) through the mounting plate (B) into the drywall anchor (H).
ASSEMBLING THE FIXTURE
There are 4 12-inch rods (P), and 1 6-inch rod (Q) included for each side of the fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. Screw the lower end of rod onto the threaded post (R) of the lighting fixture. Place reinforcing plate (M) inside canopy (G) and the canopy (G) over the threaded post (0) of the top rod. Put the center of threaded post (0) though the wire rope noose (F) and washer (L). Lock the reinforcing plate and canopy with the wing nut (K) on threaded post (0). Hide wire rope inside the canopy (G). Secure the screw collar loop (J) into mounting plate (B).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach
the fixture’s wires to the power supply wires from the junction box. Connect
black to black (Live); white to white (grounded); grounding to grounding
(green or copper). Twist the ends of the wire pairs together. Then, twist on a
wire connector. Make sure all twists are in the same direction. Loop fixture’s
ground wire around grounding screw (E) and tighten. If there is no ground wire
(green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Raise canopy (G) to mounting plate (B) and position mounting screws (A) so
that they protrude through the openings of canopy (G). Secure canopy (G) in
place with cap nuts (N). Secure [in order] cover (T), glass (U), and cover (V)
onto the socket (S) by screwing socket ring (W) tight. Install light bulb (not
included) in accordance with the fixture’s specifications. Do not exceed the
recommended wattage. Your installation is now complete. Turn on the power and
test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
Hunter Pro Tip:
- Twist or tape wire ends together to make it easier to pass them through the down rods.
- Threaded post may also be removed for easier wire access.
Notice
In order to use a 12in rod by itself you must first remove the post from the
Gin rod and install it on one of the ends of the 12 in rod.
NOTICE
Drill 9/64″ pilot holes in support structure to aid in securing light fixture.