Simx Lighting LHT0222 Oyster LED Round LED Bulkhead Instruction Manual
- June 1, 2024
- Simx Lighting
Table of Contents
Simx Lighting LHT0222 Oyster LED Round LED Bulkhead Instruction Manual
Thank you for purchasing this Simx Lighting Oyster Led. This luminaire is suitable for outdoor use and requires a 220V-240V AC power supply. Please read this manual thoroughly before installation and retain for future reference.
TECHNICAL SPECIFICATIONS
(!) IMPORTANT
This product is suitable for use only with a supply voltage of 220-240V AC
50/60Hz.
All electrical work must be carried out in accordance with local and national electrical codes as applicable. We strongly recommend that this light fitting is installed by a registered electrician.
Always switch power off prior to installation. A means of mains power isolation must be installed on the circuit for the purpose of safe access for any internal cleaning, recalibration, or maintenance.
This light fitting is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the appliance.
Any changes or modifications made or attempted to this product, without the prior written approval of the manufacturer, will void any and all stated warranties.
BEFORE YOU START
Please read all the instructions prior to installation. This light fitting is rated to IP66 and suitable for permanent outdoor use. Ensure the desired location does not exceed this rating.
INSTALLATION
We strongly recommend this light fitting is installed by a registered
electrician
Switch off the power supply before commencing any electrical work. To remove
the wiring cover, depress the catch on the side and lift it clear of the twin
locators opposite the catch (see Fig. 3). Mark the center of the 75mm diamater
mounting surface. Drill a pilot hole to take the center shaft of a hole
cutter, then cut the required hole. Using the template provided mark the hole
locations on the mouting surface. Drill holes through the template to suit the
mounting screws supplied. Care should be taken to avoid drilling or cutting
into concealed electrical wiring/plumbing. In the same location drill the
power cable entry hole. Firmly secure the fixing brackets to the ceiling with
the screws provided. (Fig. 1)
WIRING
Unclip the front cover and unscrew the white diffuser and locate the mounting holes for the power cable under the hinged section (Fig. 2)
Locate the power cable entry on side of the unit and slowly draw the power cable through the gland on side of the unit.
Wire the cable to the terminal block, ensuring that polarity is maintained (Brown is L and Blue is N). Failure to do this correctly may result in damage to the unit.
Secure the cable into position using the saddle clamp provided, do not over tighten. Tighten external gland and refit the black plastic cable cover.
Secure LED panel and carefully secure the diffuser and cover into position (use locator lug inside cover to align correctly).
Clip luminaire into position on the fixing brackets already installed. (Fig. 3)
Check all work before reconnecting the power supply.
To maintain IP rating, correct cable for gland is round core 6mm twin.
PRODUCT COMPLIANCES
Product complies with
This product conforms to relevant AZ/NZS standards.
MANUFACTURERS EXTENDED WARRANTY
This product is guaranteed by SIMX Ltd and Ventair Pty Ltd for 36 MONTHS from the date of purchase against faulty materials or workmanship which affects its designed ability to detect or switch. During this period if the product has a defect of this nature it will be repaired or replaced free of charge by SIMX with the same item, or a similar one of higher specification. ON CONDITION THAT:
The buyer returns it to the seller from whom it was bought, freight paid.
The product has been bought by the user i.e. a receipt/sales invoice is produced as proof of purchase.
The product has not been misused or handled carelessly, installed in anyway contrary to the installation instructions, or installed in any unusually exposed or harsh environmental conditions.
This guarantee excludes liability for discolouration of paint or plastic, or any user replaceable parts. It does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage.
Our Goods come with guarantees that cannot be excluded under the Australian and New Zealand Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if the Goods fail to be of acceptable quality and the failure does not amount to a major failure.
Distributed in New Zealand by Simx Ltd
Ph: +64 9 259 1660 | Technical Support Ph: +64 9 259 1662
e: sales@simx.co.nz |
www.simx.co.nz
Distributed in Australia by Ventair Pty Ltd.
4 Capital Place, Carrum Downs, 3201 VIC, AUSTRALIA. Technical Support: 1300
665 926
e: info@ventair.com.au |
www.ventair.com.au |
www.simx.com.au
Specifications are subject to change without notice
References
- Ventair Australia - Heating & Ventilation Solutions for Sale
- Ventair Australia - Heating & Ventilation Solutions for Sale
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>