weiwo intelligent G232 4G Smart Watch User Manual

June 1, 2024
weiwo intelligent

G232 4G Smart Watch

Specifications:

  • Product: 4G Smart Watch

  • Features: Quick call key, Back key, Power on and off button,
    Heart rate sensor, SIM card tray, Magnetic charging port

  • Charging: Magnetic charging interface

  • Recommendation: Use SV 1A or higher charger

Product Usage Instructions:

Sim Card Installation:

  1. Ensure the watch is turned off.

  2. Turn the watch to the back.

  3. Remove the screws to access the SIM card tray.

  4. Insert the SIM card following the direction of the SIM card
    notch.

  5. Insert the card tray back into the watch and secure the
    screws.

  6. Check that the card tray is flush to maintain water
    resistance.

Charging Manual:

  1. For the first use, charge the watch.

  2. Connect the magnetic cable to the magnetic charging port.

  3. Connect the cable to a power supply using an SV 1A or higher
    charger.

  4. Once charging is complete, turn off the power or unplug the
    cable.

Operating Instruction:

Refer to the user manual for detailed operating instructions and
tips on using the 4G Smart Watch.

FCC Statement:

The 4G Smart Watch complies with FCC regulations. For more
information, refer to the FCC statement in the user manual.

Frequently Asked Questions (FAQ):

Q: How do I check my heart rate using the watch?

A: To check your heart rate, navigate to the heart rate sensor
function on the watch and follow the on-screen instructions.

Q: Can I swim with the watch on?

A: The watch is water-resistant, but it is recommended to avoid
swimming with it to prevent any damage to the device.

4G Smart Watch
User Manual

Product Introduction
Quick call key Back key Power on and off button

Heart rate sensor SIM card tray
Magnetic charging port

Sim Card Installation

Charging Manual
Please confirm that the watch is turned off first, Turn the watch to the back, take out the screws, pull out the card tray, put in the SIM card in the direction of the SIM card notch, insert the card tray into the watch, and put the screws. Note: After inserting the card tray into the watch, check whether it is flush, if the card tray is inserted and warped, it will affect the water resistance of the watch.

For the first time, please charge the watch; The watch adopts a magnetic charging interface, connect the magnetic cable, and then connect the power supply. It is recommended to use SV lA or higher charger to charge the watch. When charging is complete, turn off the power or unplug the magnet cable.

Operating instruction
Swipe down on the watch face to bring up the status bar, and swipe up to exit the status bar. Swipe left on the watch face interface to bring up the main menu, and swipe right to return to the previous interface or return to the watch face interface. Quick call keys: Tap to enter the call interface. Back key: a. The dial interface rotation button rotates the dial. b. Press to return to the parent menu. Power on and off buttons: a. Short press the watch face interface to turn the screen on or off, and short press 1 time on the other interface to return to the watch face interface. b. Press and hold for 3 seconds to pop up the shutdown and restart interface.

Tips
1. . The charging cable of the wa h is a magnetic thimble contact, confirm that the charger is normal and in good contact when charging, there are no foreign objects and dirt in the position of the magnetic contact, the battery of this product is not removable, due to the loss of the product itself, the product may not be turned on due to the battery being dead after being idle for more than a month, please charge it regularly every week to ensure that the device can work normally. 2. . After the smart watch is pl ed for a long time, if you use the computer USB to charge, it will take more than ten minutes to display the charging icon, please wait patiently, it is recommended to use a 5V 1A charger to charge. 3. . Improper operation may ause the product to crash, you can press and hold the power button for 15 seconds to force restart the watch.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm full interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Specific Absorption Rate (SAR) information: This Device meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: Device has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the device kept 0mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain an 0mm separation distance between the user’s body and the back of the device. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals