altimobility DCS-U3-6K Communication Type Modem Device User Manual

altimobility DCS-U3-6K Communication Type Modem Device

FAQ

• Q: Where should I install the OD310 device?
  • A: The OD310 device should be installed in the rear of the internal fuse box of the driver’s seat with a distance of over 40cm from the human body.
• Q: What is the power source for the OD310 device?
  • A: The power is supplied from the vehicle’s battery by OBD at a voltage of 12V.
• Q: What kind of connectivity options does the OD310 device offer?
  • A: The OD310 device features Bluetooth V4.0 (BLE), UART ports, CAN communication, and a QUECTEL 4G/3G/2G Modem for seamless connectivity.

Overview

Purpose

The OD310 device is a communication-type modem device for vehicles. It allows the door lock/unlock and emergency lights of the vehicle to be controlled by collecting the vehicle data such as the door open, locked, OBD CAN, Battery status, GPS coordinates, and receiving commands from the BLE,MODEM. It recollects vehicle data such as the door open status, locked, OBD CAN, Battery status, GPS coordinates and controls. It also transmits the collected Data to the outside via the modem.

Product Overview

• Dimension: 183mm(W) x 31.3mm(H) x 71mm(D)
• Maximum input voltage: DC +35V
• Operation input voltage: DC+12V
• Consumable current:
  • 140mA@14v on operation
  • 3mA@12V on non-operation
  • 2mA@10V on sleep mode
• Operating temperature range: -20℃ to + 65℃
• Power Resource: Power supplied from vehicle’s battery by OBD (12V)
• Built-in battery: Li-ion Polymer Battery 1850mAh

Installation

• The OD310 device is installed in the rear of the internal fuse box of the driver’s seat. Its distance from the human body is over 40Cm

SPECIFICATION

processor

| Application Processor| STM32 ARM 32-bit Cortex M3
Built-In Memory (ROM)| 512KB
Built-In Memory (RAM)| 128KB

Memory

| FRAM (Reservation data save, Vehicle ID save)| ****

64Kbit

Serial Flash(Firmware update)| 1MByte
Sensor| Acceleration sensor| BMI160
Button| | Reset KEY
Modem| QUECTEL 4G/3G/2G Modem| EG21-G
Bluetooth| Bluetooth V4.0 (BLE)| BDE-BLEM201P

External interface

| UART 2 EA| RFID & Touch keypad
CAN Communication| 1EA
Status check input ports| 4EA
Control output ports| 4EA
Support power supply of external devices| 12V-1A(for Start prevention relay)
Start prevention control| Support

FCC STATEMENT

FCC/IC

• FCC ID: 2BDBU-DCSU36K
• Contains FCC ID: XMR201906EG21G
• IC: 31548-DCSU36K
• Contains IC: 10224A-201906EG21G

FCC Part 15.19

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Part 15.21

Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 40 cm between the radiator and your body.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.

ISED Warning Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED RF Radiation Exposure Statement: This equipment complies with ISED RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 40 cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>