TOSHIBA TMRCD210 Remote Controller User Manual

TOSHIBA TMRCD210 Remote Controller

Specification

• Name: RF 2.4G Remote Controller RF 2.4G USB Dongle
• Model No.: TMRCD210TX (Controller) TMRCD210RX (USB Dongle)
• Function: RF 2.4G Keyboard Version 1.0
• Transmit Rate: 250KHz bps
• Frequency: 2.4GHz
• Power Output: TMRCD210TX – 3.15 dBm / 2 mW,TMRCD210RX – -1.81dBm / 1 mW
• Function: HID-compliant device for both Controller and USB Dongle
• Modulation: GFSK

Product Usage Instructions

Function Description

1. The remote controller transmits an RF signal to the USB receiver dongle.
2. The USB Dongle is defined as a standard HID device. When plugged into a PC USB port, it receives RF signals from the remote controller transmitter.
3. Pairing: Plug the USB dongle into the PC and start pairing within 10 seconds. Power on the Controller and simultaneously press buttons for 3-5 seconds within 10 cm from the USB dongle.

Power Consumption

• Normal Mode: When the user operates the controller, it consumes less than 20mW.
• Sleeping Mode: If the user hasn’t used the controller for 1 second, it enters sleeping mode with a power consumption of less than 0.1mW. Press any button to wake it up.

FAQ

• Q: What should I do if the controller is not pairing with the USB dongle?
• A: Make sure the USB dongle is properly plugged into the PC and within range of the controller. Restart the pairing process by following the pairing instructions provided in the manual.
• Q: How can I conserve power when not using the controller?
• A : The controller automatically enters sleeping mode after 1 second of inactivity, consuming very low power. Press any button to wake it up when needed.
• Q: Can I modify or make changes to the device?
• A : Any modifications not explicitly approved by the manufacturer may void your authority to operate the equipment. Please refer to the manual for operating instructions and compliance.

Product Profile

1. RF2.4G Remote Controller.
2. RF 2.4G USB Dongle for keyboard.

Electrical Characteristic

TMRCD210RX

USB Dongle

| Transmit rate| 250KHz bps
---|---|---
Frequency| 2405.0MHz    –    2476.0MHz
Power out (FCC/MIC)| 3.15 dBm / 2 mW
Function| HID-compliant device,
Modulation| GFSK

TMRCD210TX

Controller

| Transmit rate| 250KHz bps
Frequency| 2405.0MHz    –    2476.0MHz
Power out (FCC/MIC)| -1.81dBm / 1 mW
Function| 2.4G Wireless Transmission
Modulation| GFSK

The key value is default as below:

FUNCTION DESCRIPTION

1. The remote controller transmits an RF signal to the USB receiver dongle.

2. USB Dongle
   The dongle is defined as a standard HID device. When it is plugged into the PC USB port, the USB Dongle will receive an RF signal from the remote controller transmitter.

3. Pair

4. Plug the USB dongle into PC and start pairing in 10 seconds.

5. Power on the Controller, and Simultaneously press ” “ buttons 3~5sec Within 10 cm from the USB dongle

POWER CONSUMPTION

1. Normal mode
   When the User operates the controller, it’s in normal mode; power consumption is less than 20.

2. Sleeping mode
   If the user hasn’t used the controller for 1 SECS, it will enter sleeping mode, power consumption is less than 0.1mW. Users can press any button to wake it up.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. To maintain compliance with FCC exposure compliance requirements, please follow operation instructions as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>