T3 76656 Air Brush User Guide
- June 1, 2024
- T3
Table of Contents
T3 76656 Air Brush
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:
DANGER KEEP AWAY FROM WATER
Electricity and water are a dangerous combination and can cause death by
electric shock. Do not allow electrical cords to come into contact with water
or other liquids.
ELECTRICAL APPLIANCES ARE ELECTRICALLY LIVE WHEN PLUGGED IN, EVEN IF TURNED
OFF. To reduce the risk of death by electric shock:
- Always unplug the appliance immediately after using.
- Do not use while bathing.
- Do not place or store the appliance where it can fall or be pulled into a bath tub or sink.
- Do not place in or drop into water or other liquid.
- If the appliance falls into water, unplug it immediately. Do not reach into the water.
WARNING To reduce the risk of burns, electrocution, fire or injury to persons:
- An appliance should never be left unattended when plugged in.
- Close supervision is necessary when this appliance is used on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water. Return the appliance to a service center for examination and repair.
- Keep the cord away from heated surfaces. Do not wrap the cord around the appliance.
- Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair and the like.
- Never use while sleeping.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Do not use an extension cord with this appliance.
- Do not direct hot air toward eyes or other heat sensitive areas.
- Attachments may be hot during use. Allow them to cool before handling.
- Do not place the appliance, while it is operating, on any surface.
- While using the appliance, keep hair away from the air inlet.
- Do not operate with a voltage converter.
- Do not operate the appliance without an attachment.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- When the blow dry brush is used in a bathroom, unplug it after use since the proximity of water presents a hazard even when the blow dry brush is switched off.
- For additional protection, the installation of a residual current device (RCD) having a rated residual operating current not exceeding 30 mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.
GROUND FAULT CIRCUIT INTERRUPTERS
If you must use your blow dry brush in the bathroom, install a GFCI now! Your
local electrician can help you decide which type is best for you – a portable
unit that plugs into the electrical outlet or a permanent unit installed by
your electrician. The National Electrical Code now requires GFCIs in the
bathroom, garages and outdoor outlets of all new homes.
Why do you need a GFCI?
Electricity and water don’t mix. If your interchangeable blow dry brush
falls into water while the dryer is plugged in, the electric shock can kill
you, EVEN IF THE SWITCH IS “OFF”.
A regular fuse or circuit breaker won’t protect you under these circumstances.
A GFCI offers you far greater protection.
A GFCI can save your life! Compared to that, the price is small! Don’t
wait…Install one now!
- GFCI is a sensitive device which reacts immediately to a small electric current leak by stopping the electricity flow.
OPERATING INSTRUCTIONS
SERVICING OF DOUBLE-INSULATED APPLIANCES
In a double-insulated appliance, two systems of insulation are provided
instead of earthing. No earthing means is provided on a double-insulated
appliance, nor should a means for earthing be added to the appliance.
Servicing a double-insulated appliance requires extreme care and knowledge of
the system, and should be done only by qualified service personnel.
Replacement parts for double-insulated appliances must be identical to the parts they replace. A double-insulated appliance is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”. The symbol (square within a square) may also be marked on the appliance.
This appliance is intended for household use. Use on Alternating Current
(60 Hz) only.
This appliance has a polarized plug (one blade is wider than the other). As a
safety feature, this plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified technician. Do not attempt to defeat this safety
feature.
CHECK ALCI EVERY TIME YOU USE THIS BLOW DRY BRUSH
This blow dry brush is equipped with an Appliance Leakage Circuit Interrupter
(ALCI), a safety feature that renders it inoperable under some abnormal
conditions, such as immersion in water. To make sure the ALCI is functioning
properly and the exclusive water sensing system (ALCI) is working, perform the
following test:
- Plug in the blow dry brush and press the test button on the plug
- The blow dry brush will stop working. There will be an audible click and the reset button will pop out.
- To reset the ALCI with a Reset button: Unplug the unit. Then push the Reset button in, and reinsert the nlus into the outlet
- Be sure to repeat the test every time you use this blow dry brush to confirm the ALCI is operational.
- If the ALCI is not functioning properly, return the blow dry brush to a service center.
- If a water immersion occurs, bring this unit into a service center. Do not try to reset.
Should the dryer go off and the Reset button pop out during use, this could indicate a malfunction in the dryer. Remove the plug from the outlet and allow the dryer to cool. Reset the ALCI. Reinsert the plug into the outlet. The dryer should function normally. If not, return it to a service center for examination and repair.
TEMPERATURE GUIDE
For optimal results, select the right heat setting for your hair type. See temperature guide below to determine your heat setting. We suggest starting at a lower setting and building your way up as needed.
- To adjust heat settings, twist the top half of the DualTwist dial to the right.
- To power on and adjust speed settings, twist the bottom half of the DualTwist dial to the right.
- To power off, turn bottom half of the DualTwist dial all the way to the left.
HOW TO USE
-
For best results, use a towel or allow hair to air-dry until hair is free of any excess moisture.
-
Thoroughly detangle hair, then use clips to divide hair into 3-4″ sections before styling.
Styling Tip: Those with fragile or color-treated hair should take extra care to eliminate excess moisture prior to styling. -
Place brush at the roots of selected hair section and slowly pull through hair while applying tension.
- For smooth, sleek blowouts, place brush close to roots and brush down through the ends.
- For voluminous blowouts, place brush under hair, close to the roots, and roll outward to the ends. For extra lift at the roots, hold the brush under the roots for 2-3 seconds.
- To create bends and curls at the ends, place the brush under the ends of each section, rotate inward or outward, and hold for 2-3 seconds.
-
Finish each section by twisting the DualTwist dial to Cool to apply a burst of cool air and set your style. Repeat until desired result is achieved.
FILTER CLEANING INSTRUCTIONS
For optimal performance, clean your T3 AireBrush filter. Simply brush or wipe
away dust buildup with a soft cloth or small brush. 
MAINTENANCE INSTRUCTIONS
- Make sure that the inlet and outlet grills are clear of dust and lint for proper operating performance.
- Your blow dry brush is virtually maintenance free. No lubrication is needed.
- Always remove the plug from the outlet and allow the dryer to cool before cleaning.
- Use a soft cloth or a small brush to remove dust and lint that may have accumulated on the rear filter of the dryer.
- The blow dry brush exterior may be wiped clean with a damp cloth.
- CAUTION : Never allow the power supply cord to be pulled, twisted or severely bent. Never wrap the cord tightly around the dryer. Damage will occur at the high flex point of entry into the blow dry brush, causing it to rupture and short. Inspect the cord frequently for damage. Stop use immediately if damage is visible, if the unit stops or if it operates intermittently.
- If the cord or blow dry brush is damaged or does not operate properly, return it to a service center for repair.
- This blow dry brush has no user serviceable parts. Do not attempt to repair the appliance yourself.
- Remove hair from the brush after every use. To keep bristles in best condition let unit cool before storing.
STORAGE
When not in use, your blow dry brush should be disconnected and stored in a
safe, dry location, out of reach of children. Do not wrap the cord around the
dryer. Allow the cord to hang or lie loose and straight at the point of entry
into the blow dry brush.
T3 LIMITED WARRANTY TERMS & CONDITIONS
T3 Micro will repair or replace (at our option) T3 products for twenty- four (24) months from the date of purchase if they are defective in workmanship or materials. This limited warranty does not cover (1) damage due to misuse or abuse, such as incorrect voltage supply, dropping, or failure to follow enclosed instructions or (2) tampering, such as repair or attempt to repair. To obtain service under this warranty, please visit www.T3Micro.com/warranty- info to submit a warranty claim, or call us at 866-376-8880 to receive detailed instructions. You will be required to provide proof of purchase.
THIS LIMITED WARRANTY IS ONLY VALID IF THE PRODUCT IS PURCHASED FROM AN AUTHORIZED SELLER OF T3 GOODS AND IF THE ORIGINAL SERIAL NUMBER ON THE PRODUCT HAS NOT BEEN REMOVED OR OTHERWISE TAMPERED WITH.
Any implied warranties, obligations, or liabilities, including but not limited to the implied warranty of merchantability and fitness for a particular purpose, shall be limited in duration to the 24 month duration of this written limited warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
IN NO EVENT SHALL 13 BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED.
Visit www.T3Micro.com/customer-service to complete your warranty registration.
SUPPLIER’S DECLARATION OF CONFORMITY 47 CFR § 2.1077 COMPLIANCE INFORMATION
-
Model Name : T3 AireBrush
-
Model Description: One-step smoothing & volumizing blow dry brush
-
Model Number: 76656, 76658
-
Responsible Party in USA: T3 Micro, Inc.
880 El Segundo Ca 90245
866.376.8880 -
Test Report Number: CN238YFX 001
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
No change or modification to this equipment shall be made without the express written approval of the “responsible party” as defined in the FCC’s rules.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>