T3 77562 Switch Kit User Guide

T3 77562 Switch Kit

Model No: 77562, 77563, 775ATT1, 775ATT2, 775ATT3, 775ATT4, 775ATT5, 775ATT6, 775ATT8, 775ATT9, 775AT10

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING

When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:

DANGER: KEEP AWAY FROM WATER

Electricity and water are a dangerous combination and can cause death by electric shock. Do not allow electrical cords to come into contact with water or other liquids.

ELECTRICAL APPLIANCES ARE ELECTRICALLY LIVE WHEN PLUGGED IN, EVEN IF TURNED OFF.

To reduce the risk of death by electric shock

1. Always unplug the appliance immediately after using.
2. Do not use while bathing.
3. Do not place or store the appliance where it can fall or be pulled into a bath tub or sink.
4. Do not place in or drop into water or other liquid.
5. If the appliance falls into water. unplug it immediately. Do not reach into the water.

WARNING

To reduce the risk of burns, electrocution, fire or injury to persons

1. An appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used on, or near children or individuals with certain disabilities.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or ifit has been dropped, damaged, or dropped into water. Return the appliance to a service center for examination and repair.
5. Keep the cord away from heated surfaces. Do not wrap the cord around the appliance.
6. Never use while sleeping.
7. Never insert any object into the styling iron.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Do not use an extension cord with this appliance.
10. This styling iron is hot when in use. Do not let eyes and bare skin touch the heated surfaces.
11. Do not place the heated styling iron directly on any surface while it is hot or plugged in.
12. Do not use if the plug is loose in the outlet, as there may be risk of fire, electric shock, electrical shortage and burning.
13. Make sure to remove the plug from the wall outlet after use.
14. With the Curl Trio, Wave Trio, and Switch Kit Base use the heat resistant glove included with the tool as recommended during operation to protect against accidental burns in the event your hand comes in contact with the heated barrel.

WARNING: Do not use the appliance near a bath tub, washbasin or other vessel filled with water. Never place the appliance in water or any other liquid.

SAVE THESE INSTRUCTIONS

MAINTENANCE INSTRUCTIONS

1. Your appliance is virtually maintenance-free. It contains no user serviceable parts. and no lubrication is needed.
2. Keep heated surfaces clean and free of dust, dirt and hairspray.
3. If cleaning becomes necessary, disconnect the appliance from the power source and let it cool. Wipe the exterior with a damp cloth.
4. If any malfunction occurs, unplug the appliance, allow it to cool and return it to a service center to repair.
5. Never wrap the cord around the appliance since this will cause the cord to wear prematurely and break. If the cord becomes twisted, untwist it prior to use.
6. Handle the cord carefully for longer life and do not put any stress on the cord where it enters the handle. Avoid jerking, twisting or straining especially at the plug connections. It could cause the cord to fray and possibly break.
7.  Do not attempt to repair the appliance yourself.

STORAGE

When not in use, your styling iron should be disconnected and stored in a safe, dry location, out of reach of children. Do not wrap the cord around the styling iron. Allow the cord to hang or lie loose and straight at the point of entry into the styling iron.

SERVICING OF DOUBLE-INSULATED APPLIANCES

In a double-insulated appliance, two systems of insulation are provided instead of earthing. No earthing means is provided on a double-insulated appliance, nor should a means for earthing be added to the appliance.

Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for double-insulated appliances must be identical to the parts they replace. A double-insulated appliance is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”. The symbol (square within a square) may also be marked on the appliance.

OPERATING INSTRUCTIONS

T3 SWITCH KIT

This appliance is intended for household use. Use on Alternating Current (50/60 Hz) only.

This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

AUTO SHUT-OFF

After approximately one hour, the unit will automatically shut itself off. To reactivate the unit, press and hold the lit Power Button until the iron vibrates, and lights start to cascade up.

AUTO WORLD VOLTAGE

This appliance contains a special electronic circuit that automatically converts it for worldwide usage – from 100 to 240 volts AC 50/60 Hz. Just plug it into the local power outlet and use it as normal; the styler will automatically adjust to the local current. You may need a plug adapter to allow the plug to fit into the local outlets.

_ Note: _Tool heat up time may vary based on country and voltage.

LED BEHAVIOR IF POWER IS ON WITH NO BARREL ATTACHED

1. LED lights 1 – 9 will cascade up once.
2. LED lights 1 – 5 will cascade up for 35 seconds before turning off (with the exception of LED light 2, which stays on).

Note: The iron will not function even if the barrel is installed. To operate, unplug the cord to reset the iron.

LED BEHAVIOR IF BARREL IS PULLED OUT WHILE IN USE

• ULED lights 1 – 9 will cascade up once, then power off.

WAND BARRELS

CAUTION: Avoid skin contact with the heated barrel as burns may occur.

CLIP BARRELS

TEMPERATURE GUIDE

For optimal results, select the right heat setting for your hair type. See temperature guide below to determine your heat setting. We suggest starting at a lower setting and building your way up as needed.

• If your hair is color-treated. reduce temperature by 1-2 heat settings for optimal results.

All T3 Switch Kit Curl Trio and T3 Switch Kit Wave Trio barrels are interchangeable. Barrels sold separately can be used with either Trio or with the T3 Switch Kit Base.

1. To attach a new barrel, unlock the handle by twisting the TightTwist lock from horizontal position to a vertical position.
2. Align the pin on the barrel with the side slot on the handle and insert the barrel firmly into the handle.
3. Rotate the TightTwist lock back to the horizontal position to secure the barrel in place.

Note

• Barrels may be hot to the touch. Wear included protective glove when handling barrels during your styling session.
• All T3 Switch Kit barrels are compatible with the original T3 Convertible Collection Power Base.

1. Press the Power & Temperature Button to turn the iron on. Lights will cascade up, then turn solid when the unit is ready to use.
   • Note: Each time you turn on the iron it will heat up to the last set temperature.
2. To change the temperature, double click the Power & Temperature Button. Then continue to click to cycle through to your exact temperature setting.
3. Release the Power & Temperature Button after selecting your desired temperature. The temperature lights will cascade up or down to your selected temperature. Lights will turn solid when the iron is ready to use.
4. To turn off the iron, press and hold the Power & Temperature Button until the lights turn off.

HOW TO USE YOUR WAND BARRELS

CREATE CURLS AND WAVES

1. Always begin with dry hair. Hold the wand over your head with the tip pointing down. Then, starting from the roots, wrap a 1-2″ section of hair around the barrel.
2. Hold for a few seconds, then slide the wand out to release the curl. For a relaxed finish, gently tug on the curl or lightly brush out the hair.

ENHANCE NATURAL CURLS

1. To enhance natural texture using the 4″ wand barrel, start with completely dry curls. Wrap inconsistent or frizzy curls around the barrel to refresh and define.
   • Note: For optimal results, style in sections that are no larger than 4″.
2. Follow instructions as listed above, repeating until desired look is achieved.
   • Pro tip: Alternate wrapping direction for a more organic look.

CLIP BARRELS

1. Always begin with dry hair. Insert the tip of a 1-2″ section of hair into the clamp and roll the iron upwards toward the scalp.
2. While rolling, make sure the hair does not overlap itself around the barrel. The entire section of hair must be evenly wrapped around the barrel.
3. Hold the iron until the heat has fully penetrated the hair section. Then carefully open the clamp and release the curl.
4. Repeat this for the remaining sections of hair. For a loose wavy curl, tug slightly on the curled section before allowing it to cool.

T3 LIMITED WARRANTY TERMS & CONDITIONS

T3 Micro will repair or replace (at our option) T3 products for twenty-four (24) months from the date of purchase if they are defective in workmanship or materials. This limited warranty does not cover (1) damage due to misuse or abuse, such as incorrect voltage supply, dropping, or failure to follow enclosed instructions or (2) tampering, such as repair or attempt to repair. To obtain service under this warranty, please visit www.T3Micro.com/warranty- info to submit a warranty claim, or call us at 866-376-8880 to receive detailed instructions. You will be required to provide proof of purchase.

THIS LIMITED WARRANTY IS ONLY VALID IF THE PRODUCT IS PURCHASED FROM AN AUTHORIZED SELLER OF T3 GOODS AND IF THE ORIGINAL SERIAL NUMBER ON THE PRODUCT HAS NOT BEEN REMOVED OR OTHERWISE TAMPERED WITH. Any implied warranties, obligations, or liabilities, including but not limited to the implied warranty of merchantability and fitness for a particular purpose, shall be limited in duration to the 24 month duration of this written limited warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

IN NO EVENT SHALL T3 BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED.

Visit www.T3Micro.com/customer-service to complete your warranty registration.

SUPPLIER’S DECLARATION OF CONFORMITY

47 CFR § 2.1077 COMPLIANCE INFORMATION

• Model Name: T3 Switch Kit
• Model Description: Interchangeable styling kit
• Model Number: 77562, 77563, 775ATT1, 775ATT2, 775ATT3, 775ATT4, 775ATT5, 775ATT6, 775ATT8, 775ATT9, 775ATIO
• Responsible Party in USA: T3 Micro, Inc. 880 El Segundo Ca 90245 866.376.8880
• Test Report Number: 220816144GZU-001

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

No change or modification to this equipment shall be made without the express written approval of the “responsible party” as defined in the FCC’s rules.

SPECIFICATIONS

• Operating Voltage: 100-240V, 50/60HZ
• Power consumption: 96W(MAX)

T3 Micro, Inc.
Made in China

WARNING: Do not use the appliance near a shower. bathtub, washbasin or other vessel filled with water. Never place the appliance in water or any other liquid.

0184-77562-C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>