TC S15-1500W Portable Power Station User Manual

S15 Portable Power Station
1500W/300000mAh

1500W
MAX POWER&960WH
POWER STATION

S15-1500W Portable Power Station

Prepared by: ……………….. Checked By: …………………….. Approved by: ……………………
Client acknowledgement:
Signature:
Date:

Product Version Change Description

Versions| Content Description| Modified by| Approver| Effective date
---|---|---|---|---
PD version| V2.03| | | 2022/6/21
BMSversion| Apr 30 2022 15: 36  :03| | | 2022/6/21
INVversion| May 16 202215: 00 :  49| | | 2022/6/21
| | | |
| | | |
| | | |

Product Description

This manual applies to the relevant characteristics of the Sany Smart Portable Mobile Energy Storage Power Supply $15 and is the basis for product design, production and inspection. The design system consists of a lithium iron phosphate 10S1P battery protection board, PD circuit, DC charging circuit, MCU control circuit, bi-directional inverter circuit and LCD screen. Inverter 1500W pure sine wave AC 220-240V 50Hz/60Hz, DC12V/10A, USB QC3.0, TYPE-C PD3.0, suitable for camping, emergency communication, medical rescue, fire rescue, etc. The product is suitable for camping, emergency communication, medical rescue, fire rescue, etc. Translated with www.DeepL.com/Translator (free version)

General Product Specifications

Product Specifications

Switch controlled by keypad
AC IN, AC OUT, SOLAR status (active status icon lit)| AC OUT is switched by key control; AC IN, SOLAR are automatically controlled by input detection
Remaining capacity SOC: percentage,
5 cell power column (20% per cell)| Charging status with ice blue power bar; discharging status with red power bar below 20% and Above 20% power bar ice blue
Time remaining| Minimum display in minutes, maximum display 99 hours 11
Charging and discharging state| (Discharge state: USE; Charge state: )
Warning Message| Over temperature, overload
Fan status| Rotate, stop
Menu functions| Language (Chinese, English, Japanese); AC OUT frequency (50Hz, 60Hz); screen brightness (11 levels of adjustment); charging speed (fast charging 2H, slow charge 5H);| Controlled via a five-way button in the middle of the display panel
Timed shutdown| Execution in non-charging mode after setting, max. 24 hours, min. 1 minute
Power supply software version information| Includes PD, BMS and INV
Power-on static consumption| | 0.8W
Over temperature protection| Over temperature protection| PD 105°C, inverter 95°C
Overtemperature recovery| Iiverter 80°C
Over temperature protection| Discharge| -20°C-60°C±3°C
Charging| 0°C-60°C±3°C

Lithium iron phosphate protection plate battery characteristics

circuit in external circuit
| Short circuit protection release conditions| Disconnecting short-circuit loads
Current consumption| IDD| Internal circuit consumption during operation| 150mA

Product discharge time

1000W
| | |

Product reliability testing

Serial number| Test items| Inspection standards| Test result
---|---|---|---
1| Constant temperature and humidity testing| Put the fully charged power supply into a temperature-controlled box at 40°Ct5°C and relative humidity of 90%-95% for for 12 hours, and after  removing it, place it at an ambient temperature of 25°Ct5°C for 2 hours and then test the performance of the product. The performance of the product is then tested.| OK
2| High temperature test (discharge)| Place the fully charged power supply into a high temperature chamber at an experimental temperature of 55°C: 5°C for 2 hours and then remove Place in ambient temperature of 25°C±5°C for 2 hours and then test the performance of the product.| OK
3| Low temperature test (discharge)| Put the fully charged power supply into the experimental temperature -10°C5°C cryostat, place it for 2 hours and then remove it in ambient temperature of 25°C±5°C for 2 hours and then test the performance of the product.| OK
4| High temperature test (charging)| Place the discharged power supply in a high temperature chamber at 40°C:5°C for 2 hours and then remove it. at an ambient temperature of 25°C5°C for 2 hours and then measure the performance of the product. test.| OK
5| Low temperature test (charging)| Put the discharged power supply into the experimental temperature -10°C±5°C cryostat, place it for 2 hours and then remove it in ambient temperature of 25°C±5°C for 2 hours and then test the performance of the prods| OK
6| Vibration testing| Harmonic vibration at a frequency of 100Hz for not less than 10 minutes for, 10 minutes, followed by experiments Testing of product performance.| OK
7| ( Drop test (box)| The product was dropped from 0.5m height onto a hardwood board with a thickness of 18-20mm (X, V. Z 6 directions respectively), the shell does not crack, and then the product performance is measured after the experiment. After the test, the performance of the product will be tested.| OK
8| ESD Testing| Contact discharge: 3KV for 10 seconds 1 time every 1 second for 10 seconds, then test the product performance after the experiment.| OK

List of standard equipment

List of options

Product Function Description

press downwards to Light up the “SETING” icon in the settings menu. Press inwards to enter the main settings menu. (50Hz, 60Hz), screen brightness (11 levels), charging speed (2H for fast charging, 5H for slow charging), timer Press inwards for 3 seconds to switch off the power supply. 515
(2)| USB-A/C Output control switch| When ON, the indicator light is on, (3), (4) and (5) start working and the (1) and (2) icons are on, when the device is connected The total output power is displayed in real time when the device is plugged in, when it is switched off (OFF), the indicator Light goes off, (3), (4) and (5) stop working and (1) and (2) icons go out
(3)| USB-A 2.0 interface| Supports QC3.0 protocol, 5V/3A, 9V/2A, 12V/1.5A for standalone use 4
(4)| USB-A 3.0 interface| Support QC3.0 protocol, support 5V/3A, 9V/2A, 12V/1.5A when used alone
(Note: (3) and (4) support 5V/2.4A dual output max 24W when used together)
(5)| USB-C interface| Support PD protocol, 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/5A, max output 100W 1
(6)| Car charger with DC 5521
interface Output control switch| When ON, the indicator lights up, (7) and (8) start working and the ® icon lights up, and the total output power is displayed in real time when the device is connected. The total output power is displayed in real time when the device is connected; when it is switched off (OFF), the Indicator light goes off, (7) and (8) stop working and the ® icon goes out
(7)| DC5521 interface| Supports 13.6V/3A 40.8W MAX dual output
(8)| Car charger interface| Supports13.6v/10A 136W MAX output
(9)| Storage compartment switch| The storage compartment can be opened by pressing downwards, with damped positioning for 110 degree opening and angle adjustment. LED auxiliary lighting, open, switch mode, close via VII

Product Function Description

working and the 0 icon lights up, @ shows the total output power in real time when the device is connected. When the device is connected, the total output power is displayed in real time; when it is switched off, the indicator Light goes off, I stops working and the 0 icon goes off J
III| AC charging port| Connected to the grid via the AC connection cable included with the main unit, supports 220V (50Hz/60Hz) 800W MAX charging
IV| Anderson Interface| Supports 10-65V 800W MAX DC charging

comes on and VI lights up at 50% brightness; when the button is pressed again, A lights up at 100% brightness When the key is pressed again, A lights up at 100% brightness and flashes at the ‘SOS frequency% when the key is pressed again, the light turns off and A stops working. When the key is pressed again, the light turns off and A stops working; the key works in this cycle

Product Function Description

in (2) )
(2)| USB-C interface status indication| Switch control via (“Interface keys’ in (2) )
(3)| DC interface status indication| Switch control via (“Interface keys’ in (6))
(4)| Total input power display| Real-time power display when charging the 515
(5)| Fan status display| St 5 is equipped with two fans, the icon lights up when the fan is working and goes out when the fan is off
(6)| Remaining time and usage status display| When charging, with “lightning’ icon, FAST stands for fast charging mode, SLOW stands for slow charging mode, the number represents the time required for full charge, the minimum display unit is minutes, the maximum display unit is hours; when discharging, with When discharging, with “USE”, the number represents the time left to discharge, the minimum display unit is minutes, the maximum display unit is hours
(7)| Setup menu| Can be personalised according to user requirements “!
(8)| 515 temperature alarm| When overtemperature is triggered the icon flashes for 10 seconds, 515 switches off all outputs and resumes them when the temperature returns to normal
(9)| Total output power display| Display of real-time output power

Product Function Description

power, the icon lights up and (4) shows the charging power
(11)| AC OUT interface status indication| The switch is controlled by means of the II in the “interface keys”. The panel display is for the 110V low-voltage version ; the panel display is for the 220V high-voltage version
(12)| AC IN interface status indication| The icon lights up when the IV is connected with electricity and goes out when it is disconnected
(13)| S15 Automatic shutdown execution
time countdown| Can be set via “SETING”
(14)| Power indicator column| 5 cells (20% per cell), charging state, ice blue power bar; discharging state, below 20% power bar red, above 20% power bar ice blue Above 20% power bar ice blue
(15)| AC OUT output frequency display| = Can be set via “SETTING”
(16)| Percentage of power display| Display accuracy 1%
(17)| Overload warning icon| Icon illuminates when the access device of S15 is overloaded or short-circuited I

Product Handling Precautions

1. Please use the $15 within the permissible operating temperature range. Use outside the optimum operating temperature may cause the S15 to exceed its safe and effective operating limits. The $15 may be used outside its safe and effective operating limits.
2. Donot submerge the main unit in water, the $15 is not waterproof. Please take care not to void the terms of the warranty by using it in a waterproof manner.
3. Continuous use of high-powered electrical output may result in over-temperature protection due to the high temperature of the main unit, whichis anormal phenomenon. to 1 hour before discharging or charging.
4. The S15 must be charged with the official charging cable, and we will not be responsible for any consequences caused by charging with non-original accessories. We will not be held responsible for any consequences caused by non-original accessories.
5. When charging, please place the machine on a level surface with no flammable or combustible materials around, and keep an eye on the site while the product is charging to prevent accidents.
6. After continuous full discharge, if the product battery is at a high temperature, it is recommended to wait until the machine has cooled down to room temperature before charging. Otherwise there may be a prohibition on The battery can be charged at an ambient temperature of 0°C to 40°C. The battery can be charged at an ambient temperature of 0°C to 40°C. The ideal ambient temperature for charging (22-28°C) can significantly extend the battery’s The ideal charging temperature (22-28°C) will significantly extend the life of the battery.

Common product troubleshooting

1. The power display jumps when the device is discharged, such as: the power display shows 36% when it is not discharged, and the power drops to 30% instantly when it is discharged, this situation belongs to the device is not executed. Discharge the device to 0% and automatically shut down, then turn on the device and still automatically shut down, then charge the device to If the device is discharged to 0% and turns off automatically, then the device is charged to 100% and the input power is 0, as shown in the figure
   below , the charging icon lights up, as shown in the figure on the right , and can be excluded.

2. Device USB-A, TYPE-C connected to the load output no power, check whether the interface is plugged in place, or there is loose.

3. If the device’s cigarette lighter is connected to a load with no power output, check whether the interface is plugged in place or is loose.

4. Turn on the inverter display or Does not light up , charge the device with AC Does not light up , check the 4P wire in the diagram below for poor contact.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>