RAVAK Galaxy TOSCA LA Shower Trays Instruction Manual
- June 3, 2024
- RAVAK
Table of Contents
RAVAK Galaxy TOSCA LA Shower Trays
Contents of the assembly pack
- Plastic clip 4 pcs.
- Dowel 8 mm 4 pcs.
- Screw 4×40 mm 4 pcs.
- Round base 12/4,3 4 pcs.
ASSEMBLY INSTRUCTIONS
The type LA shower trays are manufactured for building in the floor, or for bricklaying. Both variants must be done by an expert – bricklayer. The shower tray can be used in a niche by itself, or with any compatible shower enclosure manufactured by the RAVAK company. We recommend that you complete the trays by a siphon RAVAK BASIC (PROFESSIONAL) 90.
-
a.b. Remove the top siphon cover using a flat, blunt object and take out the sludge trap. Using the shoulders on the inside diameter, unscrew the siphon. Use a wrench of diameter 90 mm to assemble.
-
a,b. Place the tray provisionally in the required position and mark the location of the siphon on the floor. Next, mark the height of the upper edge of the tray on the wall.
2c. The upper edges should be level. The difference in height (see the picture 2c) between the seat and the edge of the tray has to be about 185 – 190 mm. -
a,b. Make the outlet piping (diameter 40 mm) and prepare the connection to the siphon.
-
a,b. Place the shower tray in its final position again, fit the siphon correctly and mark the position of the pipe joint. Finish the connection of the outlet pipes and bottom part of the siphon.
-
a,bc. The new trays are modified for hanging from the edge to clips on the wall. It is necessary to mark the centre of the clip in a distance 100 mm from the corners of the tray. Drill a hole (diameter 8 mm) 40 mm from the upper edge, space and fit the dowel.
-
Space out the clips (pict. 6), using 2 pcs on the higher corner of the tray (seat). On both sides place them in a distance 100 mm from the corner of the tray. Then mount the angular tray TAURUS in the niche.
-
a,b. Screw on the plastic clip (the shorter claw up – see the picture), check the fixing of the tray.
-
a,b. Prepare the brick bed for the tray to the desired height to fit the entire surface of the tray bottom. Apply a mortar layer to a thickness of 20 – 30 mm to the surface of the bed.
-
a,b. Place the shower tray in the correct position, screw the siphon gently and press the tray into the mortar bed in the correct position. Check and adjust the horizontal position and the height from the floor. It is necessary to apply the silicone to the claw of the clip before the final setting.
-
a,b. Finish the assembly of the siphon.
-
a,b.The final walling-in or tiling cannot be done before the hardening of the bed.
-
a,b. The tiling can be a maximum of 5 mm over the outside edge of the tray.
Notice:
We recommend using a silicone sealing compound to connect the tray with
finished tiling or other surfaces. A better seal for large joints is achieved
if mortar is used first, and then a silicone sealing RAVAK PROFESSIONAL
compound. If using another cement, there is a risk the tray will not be water-
proof. It is suitable to use the “Installation set for KASKADA shower
trays”which is produced by the RAVAK company, to achieve a professional
sealing of trays.
MAINTENANCE
Clean the plastic parts with a cloth and mild detergent. Never use strong cleansing or scouring agents, alcohols, thinners or acetone. The manufacturer accepts no liability for any type of use or care other than those contained in these instructions. The manufacturer reserves the right to introduce technical changes without notice. The guarantee is 12 months from the date of sale. For further information about assembly, use, and care contact your local dealer.
The manufacturer recommends the RAVAK ANTI CALC line of products: RAVAK CLEANER – works to remove old and dried-on debris from glass surfaces, shower frames, enamel and acrylic bathtubs, washbasins and water taps; RAVAK DISINFECTANT – is a special preparation with considerable anti-bacterial and anti-fungal effects.
RAVAK a.s., Obecnická 285, 261 01 Pøíbram 1, ÈR tel.: 318 427 111, 318 427 200
fax: 318 427 269, 318 427 278,
e-mail: smith@ravak.cz
www.ravak.com
RAVAK a.s., Obecnická 285, 261 01 Pøíbram I
tel.: +420 318 427 200, 318 427 111 fax: +420 318 427 269
e-mail: info@ravak.cz,
www.ravak.com
References
- RAVAK COM - Acrylic Bathtubs and Shower Enclosures
- RAVAK a.s. - Když koupelnu, tak RAVAK – české koupelny světového designu!
- RAVAK GmbH - Das Badeerlebnis in Ihrem Badezimmer
- RAVAK a.s. - bañeras y mamparas de baño
- RAVAK Hungary Kft. - ha fürdőszoba akkor RAVAK
- Ravak Polska S.A. - dożywotnia gwarancja na wszystkie wanny. Kompleksowe wyposażenie łazienek.
- Kúpeľňa a zariadenie kúpeľne | RAVAK
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>