tuya H3-WiFi Acess Controller Reader WiFi Version User Manual

tuya H3-WiFi Acess Controller Reader WiFi Version

INTRODUCTION

The device is a single-door multifunction standalone access controller or a Wiegand output reader. It uses Atmel MCU assuring stable performance. The operation is very user-friendly, and the low-power circuit makes it a long service life.

The device supports 1,000 users (990 common users + 10 visitor users), and all user data can be transferred from one to another It supports multi-access modes in card access, PIN access, or multi-card/PIN access. It has extra features including block enrollment, Wiegand input & output interface…etc.

Features

• WiFi 2.4G network
• Touch key
• Waterproof, conforms to IP66
• One relay, 1,000 users (990 common + 10 visitors)
• PIN length: 4-6 digits
• EM card, EM+ Mifare cards optional
• EM card: Wiegand 26~44 bits input & output
• Mifare card: Wiegand 26~44bits, 56bits, 58bits input & output
• Can be used as a Wiegand reader with LED & buzzer output
• Card block enrollment
• Tri-color LED status display
• Pulse mode, Toggle mode
• User data can be transferred
• Built-in light-dependent resistor (LDR) for anti-tamper
• The backlit keypad can set automatic OFF after 20 seconds

Specification

Carton Inventory

INSTALLATION

• Remove the back cover from the unit
• Drill 2 holes(A, C) on the wall for the screws and one hole for the cable
• Knock the supplied rubber bungs to the screw holes(A, C)
• Fix the back cover firmly on the wall with 4 flat-head screws
• Thread the cable through the cable hole(B)
• Attach the unit to the back cover

Wiring

Sound and Light Indication

Basic Configure

Enter and Exit Program Mode

Set Master Code

Set the Working Mode

Notes:
The device has 3 working modes: Standalone Mode, Controller Mode, and Wiegand Reader Mode, choose the mode you use. (Factory default is Standalone Mode/Controller Mode)

STANDALONE MODE

The device can work as a Standalone Access Control for a single door. (Factory default mode) — 7 7 #

Connection Diagram

Common Power Supply

Attention:
Install a 1N4004 or equivalent diode is needed when using a common power supply, or the keypad might be damaged. (1N4004 is included in the packing)

Access Control Power Supply

Programming
Programming will vary depending on access configuration. Follow the instructions according to your access configuration.

• Notes:
  User ID number: Assign a user ID to the access card/ PIN to track it.

  • The Common User ID: 0~989
  • Visitor User ID: 990 ~ 999
    IMPORTANT: User IDs do not have to be proceeded with any leading zeros. Recording of User ID is critical. Modifications to the user require the User ID to be available.

• Proximity Card:

  • Proximity Card: EM card/ EM+ Mifare cards

• PIN: Can be any 4~6 digits

Add Common Users
PIN/ Card user ID: 0~989; PIN length: 4-6

Tips for PIN Security (Only valid for 6 digits PIN):
For higher security we allow you to hide your correct PIN with other numbers up to a max of 9 digits.

Example PIN: 123434
You could use *(123434) or * (123434) (“” can be any number from 0~9)

Add Visitor Users
(User ID number is 990~999; PIN length: 4~6 digits) There are 10 groups of Visitor PIN/cards available, the users can be specified up to 10 times of usage, after a certain number of times, i.e. 5 times, the PIN/card becomes invalid automatically.

Delete Users

Set Relay Configuration
The relay configuration sets the behaviour of the output relay on activation.

Set Access Mode
For Multi-user access mode, the interval time of reading can not exceed 5 seconds, or else, the device will exit to standby automatically.

Set Strike-out Alarm

• The strike-out alarm will engage after 10 failed entry attempts (Factory is OFF).
• It can be set to deny access for 10 minutes after engaging or disengage only after entering a valid card/PIN or Master code/card.

Set Audible and Visual Response

Master Card Usage (Users can add the Master Cards by themselves)

Users Operation & Reset to Factory Default

• Open the door: Read a valid user card or input a valid user PIN #
• Remove Alarm: Enter Master Code # or Master Card or valid user card/PIN

To reset to factory default & Add Master Card:
Power off, press the Exit Button, hold it and power on, there will be two beeps, then release the exit button, the LED light will turn yellow, then read any 125KHz EM card / 13.56MHz Mifare card, the LED will turn into red, means reset to factory default successfully. Of the card reading, it is the Master Card.

Remarks:

• If no Master Card is added, must press the Exit Button for at least 5 seconds before release. (this will make the previously registered Master Card invalid)
• Reset to factory default, the user’s information is still retained.

CONTROLLER MODE

The device can work as a Controller, connected to the external Wiegand reader. (Factory default mode) – 7 7 #

Connection Diagram

Attention:
Install a 1N4004 or equivalent diode is needed when using a common power supply, or the reader might be damaged. (1N4004 is included in the packing)

Set Wiegand Input Formats
Please set the Wiegand input formats according to the Wiegand output format of the external Reader.

Note:
For connecting Wiegand readers with 32, 40, and 56 bits output, need disable parity bits.

Programming

• Basic Programming is the same as Standalone Mode
• There are some exceptions for your attention:

The device is connected to an External Card Reader

• If EM/Mifare card reader: users can be added/deleted on either the device or external reader.
• If HID card reader: users can only be added/deleted on extemal reader.

The device is connected to a Fingerprint Reader

For example:
Connect SF1 as the fingerprint reader to the device.

• Step 1: Add the Fingerprint (A) on SF1 (Please refer to SF1 manual)
• Step 2: Add the same Fingerprint(A) on the device:

The device is connected to the Keypad Reader

• The keypad reader can be 4 Bits, 8 Bits (ASCIl), or 10 Bits output format.
• Choose the below operation according to the PIN output format of your reader.

Remarks:
4 means 4 bits, 8 means 8 bits, 10 means 10 digits virtual number.

• Add PIN Users:
  To add PIN users, after entering into programming mode on the device, PIN(s) can be input/added on either the device or the external Keypad Reader.

• Delete PIN Users: the same way as add users.

WIEGAND READER MODE

The device can work as a Standard Wiegand Reader, connected to the third-party Controller — 78 #

Connection Diagram

Notes:

• When set into Wiegand Reader mode, nearly all settings in Controller Mode will become invalid, and Brown & Yellow wires will be redefined as below:
  • Brown wire: Green LED light control
  • Yellow wire: Buzzer control
• If you need to connect Brown/Yellow wires:
  When the input voltage for LED is low, the LED will turn Green; and when the input voltage for Buzzer is low, it will sound.

Set Wiegand Output Formats
Please set the Wiegand output formats of Reader according to the Wiegand input formats of the Controller.

Note:
For connecting the Wiegand controller with 32, 40, and 56-bit input, need to disable parity bits.

ADVANCED APPLICATION

Collection Card Mode
After this mode is turned on, all cards can open the lock. At the same time, the card is added to the device.

User Information Transfer
The device supports the User Information Transfer function, and the enrolled user (cards, PINs) can be transferred from one (let’s name it Master Unit) to another (let’s name it Accept Unit).

Connection Diagram:

Remarks:

• The Master units and Accept units must be the same series of devices.
• The Master Code of the Master Unit and the Accept Unit must be set to the same.
• Program the transfer operation on the Master Unit only.
• If the Accept Unit is already with the users enrolled, it will be covered after transferring.
• For a full 1000 users enrolled, the transfer takes about 30 seconds.

Set Transferring on Master Unit:

Documents / Resources

| tuya H3-WiFi Acess Controller Reader WiFi Version [pdf] User Manual
ch1-cf1, H3-WiFi, H3-WiFi Acess Controller Reader WiFi Version, H3-WiFi, Acess Controller Reader WiFi Version, Controller Reader WiFi Version, Reader WiFi Version, WiFi Version, Version
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>