LG Electronics TM03LNNAHD0 Telematics Module Device User Manual
- June 6, 2024
- LG Electronics
Table of Contents
LG Electronics TM03LNNAHD0 Telematics Module Device
equipped in the vehicles.
TM03LNNAHD0 as telematics module device equipped in the vehicles. In charge of wireless communications in LTE/WCDMA network Platform for Telematics Virtual Machine (VM) and other VMs based on Hypervisor TM03LNNAHD0 supports WCDMA B2/5, LTE B2/4/5/12network There will be performing some use-case to demonstrate LTE/WCDMA performances targeted
-
High throughput features
-
Low Latency features. below is just for example.
• High throughput features -
Demonstrate high-throughput, high -quality image by hotspot.
Frequency Band
Item| Uplink| Downlink| WCDMA| FDD-LTE
Band2| 1850-1910| 1930-1990| V| V
Band4| 1710-1755| 2110-2155| | V
Band5| 824-849| 869-894| V| V
Band12| 699-716| 729-746| | V
installation
NAD Module as TM03LNNAHD0 Module is mounted with a solder ball on the main TSU
board. The strength of the RF field produced by the wireless module or modules
embedded in the TSU is well within all international RF exposure limits known
at this time. Because the wireless modules embedded in the TSU emit less than
the maximum amount of energy permitted in radio frequency safety standards and
recommendations, the manufacturer believes these modules are safe for use.
Regardless of the power levels, care should be taken to minimize human contact
during normal operations. This module should remain more than 20 cm (8 inches)
from the body when wireless devices are on and transmitting. This transmitter
must not be collocated or operated in conjunction with any other antenna or
transmitter. Operation is subject to the following two conditions: (1) This
module does not cause interference, (2) this module accepts any interference
that may cause undesired operation.
Information for the integrator
The integrator must not provide information to the end-user regarding how to
install or remove this RF module in the user manual of the end product. The
user manual that is provided by the integrator for end-users must include the
following information in a prominent location. To comply with FCC RF and IC
RSS-102 exposure requirements, the antenna used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons
and must not be collocated or operated in conjunction with any other antenna
or transmitter. The label for the end product must include FCC ID:
BEJTM03LNNAHD0 or A RF transmitter inside, IC: 2703H-TM03LNNAHD0.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. The OEM
integrator is responsible for ensuring that the host product which is
installed and operating with the module is compliant with Part 15B
unintentional Radiator requirements, please note that For a Class B digital
device or peripheral, the instructions furnished the user manual of the end-
user product shall include the following or similar statement, placed in a
prominent location in the text of the host product manual:
FCC STATEMENTS
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiating element of this device and the user.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>