WALCOM 9011 Spray Gun Instructions

9011 Spray Gun
INSTRUCTIONS SPRAYGUN

9011 Spray Gun

| 9011 / 9010 / 9010 sp HVLP
9011 / 9010 / 9010 sp HTE
9011 HD
9010 / 9010 sp ECOMIX
9010 sp COLLA
9011 / 9010 sp GEL COAT
---|---
| 6011 / 6010 / 6010 sp HVLP
6011 / 6010 / 6010 sp HTE

www.walmec.com
BORN from TRADITION
Meanings of symbols used

| – Warning
---|---
| – Fire hazard
| – Burn hazard
| – Explosion hazard
| – Mandatory eye protection
| – Mandatory protective gloves
| – Mandatory body protection
| – Mandatory protective shoes
| – Mandatory hearing protection

SAFETY WARNINGS

• Before using the spray gun, carefully read the following warnings, recommendations and instructions for use!
• Keep these documents with the spray gun!

FIRE OR EXPLOSION HAZARD:

•  The spray gun is designed to be used in explosive atmospheres classified as zone 1 and 2 (ATEX Directive). Do not use the spray gun in zone 0!
• Do not use solvents and/or halocarbon based detergents (Ethyl trichloride, Methyl chloride, etc.) since they could rust galvanised parts causing even explosive chemical reactions!
• Do not smoke or produce sparks: this could cause fire!
• Always be sure that the painting equipment is earthed correctly!
•  Use antistatic compressed air tubes to prevent the accumulation of electrostatic loads!

HEALTH EQUIPMENT AND PRECAUTIONS:

• When using and cleaning the spray gun, always wear suitable protective glove and goggles, as well as specific masks with filters!
• When using and cleaning the spray gun, wear suitable and antistatic work clothing to protect the body from contact with toxic vapours, solvents or with the products in use!
• Wear suitable hearing protection when using the air gun since 85 dB(A) acoustic pressure levels may be exceeded!
• Use the spray gun only in well ventilated rooms!
• The use of some paint products containing organic solvents can cause intoxication due to the toxic fumes they emit. In every case, it is necessary to read the technical sheets for the products before use!
• The use of compressors or other pulsating pressure generators may produce vibrations that can cause injuries due to repeated stress, especially when the tube that connects the compressor to the spray gun is not sufficiently long and flexible!

IMPROPER USE RISKS:

• Never direct the jet towards people or animals!
• Never exceed the declared maximum working pressures!
• Never use components or parts that are not Asturomec® originals!
• After cleaning, maintenance and/or repairs and, in any case, before using the spray gun, make sure nuts and bolts are firmly secured in their housings!

RISKS TIED TO SPRAY GUN CLEANING:

• Before disassembly and cleaning, make sure that the spray gun has been disconnected from the supply unit!
• Never use acidic or alkaline substances for cleaning (basics, paint removers, etc.)!
• Submerge the spray gun in detergent for a maximum of one half hour!
• After cleaning, spray the gun, nozzle, cap and tank with compressed air!
• Never use metal or other objects that could damage the holes in the nozzle and cap!

WARNINGS FOR CORRECT CLEANING:
Disconnect the spray gun from the equipment before any disammembly operations!

• Remove any remaining paint by pouring it into another container.
• Disassemble the spray gun making sure to remove the needle before disassembling the nozzle to avoid damage to the housing of the nozzle closure.
• Clean all the paint passages and the nozzle. Clean the other components using a brush soaked in solvent (cleaning kit Ref. 90109/W recommended).
• Reassemble the spray gun and spray a small quantity of solvent to eliminate all the residues in the paint passages.
• Incomplete cleaning could cause function failures and a degradation of the fan form.

SPECIAL CONDITIONS FOR SAFE SPRAY GUN USE:
When using the spray gun, heat hazards may be due to:

• the use of hot compressed air;
• heated primer and finish product application. In these situations, at most, the spray gun surface reaches the compressed air or primer and finish product temperatures. In these conditions, pay ATTENTION to the following:
• the spray gun surface temperature should not exceed the burning limit of 43°C (UNI EN 1953 paragraph 5.4). If this is the case, hand protection must be worn: (for example, heat resistant antistatic gloves);
• the spray gun surface temperature should never exceed 85°C, temperature sufficiently lower than the minimum ignition temperature (TMA) of solvents commonly used for bodywork, woodwork and industrial painting;
• in case of doubt, ask your dealer for information on the solvent TMA.

The list of construction materials used will be provided upon request..

 FAILURES AND REMOVAL OF THEIR CAUSES

– Stuffing box needle worn
– Nozzle not fully tightened
– Nozzle cone ruined| – Tighten the needle stuffing box nut
– Replace the stuffing box needle
– Tighten nozzle
– Replace nozzle
UNEVEN JET| – Air cap holes are dirty or damaged – Central hole on cap is damaged or dirty
– Nozzle is dirty or damaged| – Clean carefully nozzle and cap (with cleaning kit Ref. 90109/W) if problem persists replace them.
AIR BUBBLES IN THE PAINT TANK| – Paint nozzle is loose – Nozzle is worn out| – Firmly tighten the nozzle
– Replace nozzle
PRODUCT LEAKS FROM NOZZLE DURING 1ST PHASE| – Nozzle and needle are clogged with dry paint
– Nozzle or needle is damaged
– Needle pusher spring missing| – Clean carefully needle and nozzle
– Replace needle and nozzle
– Insert the needle spring
AIR LEAKS WITHOUT PULLING THE LEVER| – Rear air stuffing box worn – Shutter worn
– Valve scratched
– OR valve worn| – Replace rear air stuffing box
– Replace shutter
– Replace valve
– Replace OR valve

MOD………………………………………………………………………………..9011 / 9010 / 9010 sp HVLP

TECHNICAL SPECIFICATIONS

• Air fitting: G 1/4” M
• Product delivery fitting (version SP): G 1/4” M
• Maximum air pressure: 5 bar (73 psi)
• Maximum product pressure (SP version): 5 bar (73 psi)

ADJUSTMENTS

• Working pressure: 2 bar (29 psi)
• Fan: Fully open
• Air: Fully open
• Product: 3-3.5 turns

Ø| Feed| Delivery pressure| **Product load| Air consumption at 0.7 bar (10 psi) captest| Fan dimensions at 20 cm (7.9″)
---|---|---|---|---|---
1.0| k SP version| 2 bar (29 psi)| | 220 Lt./min (7.8 CFM)|
1.3
1.5| Gravity Gravity Suction SP version| 218 Gr/min.(7.7 oz/min.)
256 Gr/min.(9 oz/min.)| 220 Lt./min (7.8 CFM)| 20 cm (7.9″)
21 cm (8.9″)
220 Lt./min (7.8 C
220 Lt./min (7.8 CFM)
158 Gr/min.(5.6 oz/min.)| 220 Lt./min (7.8 CFM)| 18 cm (7.1″)
PIMINIIC=Triirrin| 7.8 CFM)|
2.| Gravity Suction SP version| 302 Gr/min.(10.7 oz/min.)
180 Gr/min.(6.4 oz/min.)| 220 Lt./min (7.8 CFM)
220 Lt./min (7.8 CFM)
220 Lt./min (7.8 CFM)| 21 cm (8.9″)
18 cm (7.1″)
2.| Gravity Suction SP version| 326 Gr/min.(11.5 oz/min.)
194 Gr/min.(6.9 oz/min.)| 220 Lt./min (7.8 CFM)
220 Lt./min (7.8 CFM)
220 Lt./min (7.8 CFM)| 22 cm (8.7″)
20 cm (7.9″)
2.| Gravity Suction SP version 1| 378 Gr/min.(13.4 oz/min.)| 220 Lt./min (7.8 CFM)| 22 cm (8.7″)
216 Gr/min.(7.6 oz/min.)| 220 Lt./min (7.8 CFM)
220 Lt./min (7.8 CFM)| 20 cm (7.9″)
3.| Gravity| 482 Gr/min.(17 oz/min.)| 220 Lt./min (7.8 CFM)| 22 cm (8.7″)
Suction SP version| 230 Gr/min.(8.1 oz/min.)| 220 Lt./min (7.8 CFM)
220 Lt./min (7.8 CFM)| 21 cm (8.9″)
|

** Product flow was calculated with water, setting the recommended regulations.

RECOMMENDED AIR PRESSURE DURING USE: 2 bar (29 psi)
At the recommended air pressure the spray gun respects the European and U.S. ecological norms for which the transfer efficiency must be above 65% and /or the air pressure at the exit of the air cap must not be superior to 0.7 bar (10 psi).

USE

Spray guns int the 9000 HVLP series have been designed for the application of finishing colours in all those sectors requiring high quality finishing and low fumes emission.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:

1.  When possible, use an air pipe with a minimum internal section of ø 8 mm (0.3”).
2.  Make sure the compressed air used is perfectly filtered removing all water, oil or other impurities (for example, by installing an Asturomec filter regulator ref. 61131 and Asturomec coalescent microfilter ref. 61201, or by the more complete and efficient
   WALCOM TD3 PRO multifunctional filter and heating unit).

ADVICE FOR CORRECT USE

1. The distance between the spray gun and the surface to be painted must be set between 100 and 150 mm (3.9”- 5.9”). If the spray gun is working at too low a pressure and at too high a distance, il will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in horizontal strokes. Any eventual shift from this position when spraying will result in an uneven application of the paint layer.
3.  Correct viscosity of the paint is between 15 and 25 sec. Coppa Ford n.
4. These values depend on the application in question and the measure of the nozzle in use.

FORM OF THE FAN

| – Air pressure too low
– Product viscosity too high
– Quantity of product too high
---|---
| – Air pressure too high
– Product viscosity too low
– Quantity of product too low
| – Regular jet

Adjust the air pressure, product quantity and spray aperture until obtaining a regular imprint as in fig. C

MOD…………………………………………………………………….9010 ECOMIX – 9010 sp ECOMIX

TECHNICAL SPECIFICATIONS

• Air fitting: G 1/4” M
• Product delivery fitting (version SP): G 1/4” M
• Maximum air pressure: 5 bar (73 psi)
• Maximum product pressure (SP version): 5 bar (73 psi)

ADJUSTMENTS

• Working pressure: 2.5-3.0- bar (36-43 psi)
• Fan: Fully open
• Air: Fully open
• Product: 2.5 turns

Ø| Feed| Delivery
pressure| **Product load| Air consumption| Fan dimensions
at 20 cm (7.9″)
---|---|---|---|---|---
2.| Suction| 2.5-3.0 bar
(36-43 psi)| 1780 Gr/min.(63 oz/min.)| 200-240 Lt./min (7 – 8.5 CFM)| 20 cm (7.9″)
SP version| | 200-240 Lt./min (7 – 8.5 CFM)|
3.| Suction| 1960 Gr/min.(69 oz/min.)| 200-240 Lt./min (7 – 8.5 CFM)| 22 cm (8.7″)
SP version| | 200-240 Lt./min (7 – 8.5 CFM)|
3.0| Suction| 2750 Gr/min.(97 oz/min.)| 200-240 Lt./min (7 – 8.5 CFM)| 25 cm (9.8″)
SP version| 200-240 Lt./min (7 – 8.5 CFM)|

** Product flow was calculated with water, setting the recommended regulations.

USE
The 9010 ECOMIX spray gun has been designed for special applications, especially in the building sector.
Specially indicated for applying Alfatone and wall paints. The instrument is not suitable for the application of products containing acids or any type of petrol.
To obtain the best results, the following instructions must be followed carefully:

1. When possible, use an air pipe with a minimum internal section of ø 8 mm (0.3”).
2. Make sure the compressed air used is perfectly filtered removing all water, oil or other impurities (for example, by installing an Asturomec filter regulator ref. 61131 and Asturomec coalescent microfilter ref. 61201, or by the more complete and efficient WALCOM TD3 PRO multifunctional filter and heating unit).

ADVICE FOR CORRECT USE

1.  The distance between the spray gun and the surface to be painted must be set between 150 e i 200 mm (5.9-7.9”). If the spray gun is working at too low a pressure and at too high a distance, il will not perform to the best of its capacity.
2.  The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in horizontal strokes. Any eventual shift from this position when spraying will result in an application of the paint layer.

MOD………………………………………………………………………………………………………9010 sp COLLA

TECHNICAL SPECIFICATIONS

• Air fitting: G 1/4” M
• Product delivery fitting (version SP): G 1/4” M
• Maximum air pressure: 5 bar (73 psi)
• Maximum product pressure (SP version): 5 bar (73 psi)

ADJUSTMENTS

• Working pressure: 2.5-3.0- bar (36-43 psi)
• Fan: Fully open
• Air: Fully open
• Product: 3 – 3.5 turns

USE
Spray gun 9010 sp COLLA has been designed for special applications. Particularly indicated for the application of liquid glues.
The instrument is not suitable for applying products that may contain acids or petrol of any kind.
The spray gun can be used in connection with a pressurised tank or a specific pump.
To obtain the best results, the following instructions must be followed carefully:

1.  When possible, use an air pipe with a minimum internal section of ø 8 mm (0.3”).
2.  Make sure the compressed air used is perfectly filtered removing all water, oil or other impurities (for example, by installing
   an Asturomec filter regulator ref. 61131 and Asturomec coalescent microfilter ref. 61201, or by the more complete and efficient WALCOM TD3 PRO multifunctional filter and heating unit).

ADVICE FOR CORRECT USE

1.  Set the distance between the spray gun and the surface to be treated between 150 e i 250 mm (5.9-9.8”).
2. The jet from the spray gun must always be perpendicular to the surface being treated and the product must be applied in horizontal strokes. Any eventual shift from this position when spraying will result in an uneven application of the product layer.

MOD………………………………………………………….9011 GEL COAT – 9010 sp GEAL COAT

TECHNICAL SPECIFICATIONS

• Air fitting: G 1/4” M
• Product delivery fitting (version SP): G 1/4” M
• Maximum air pressure: 5 bar (73 psi)
• Maximum product pressure (SP version): 5 bar (73 psi)

ADJUSTMENTS

•  Working pressure: 2.5-3.0- bar (36-43 psi)
• Fan: Fully open
• Air: Fully open
• Product: 2.5-3 turns

Ø| Feed| Delivery pressure| **Product load| Air consumption| Fan dimensions at 20 cm (7.9″)
---|---|---|---|---|---
3.0| Gravity SP version| 2.5-3.0 bar (36-43 psi)| 512 Gr/min.(18 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)
180-240 Lt./min (6.4-8.5 CFM)| 18 cm (7.1″)
4.0| Gravity SP version| 676 Gr/min.(23.9 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)
180-240 Lt./min (6.4-8.5 CFM)| 20 cm (7.9″)
5.0| Gravity SP version| 730 Gr/min.(25.8 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 24 cm (9.4″)
| 180-240 Lt./min (6.4-8.5 CFM)|

** Product flow was calculated with water, setting the recommended regulations.
USE
Spray guns in the Novemila “GEL COAT” series have been designed for applying GEL COAT or dense products generally.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind. To obtain the best results, the following instructions must be followed carefully:

1.  When possible, use an air pipe with a minimum internal section of ø 8 mm (0.3”).
2. Make sure the compressed air used is perfectly filtered removing all water, oil or other impurities (for example, by installing an Asturomec filter regulator ref. 61131 and Asturomec coalescent microfilter ref. 61201, or by the more complete and efficient WALCOM TD 3 PRO multifunctional filter and heating unit).

ADVICE FOR CORRECT USE

1.  The distance between the spray gun and the surface to be painted must be set between 150 and 200 mm (5.9 – 7.9”). If the spray gun is working at too low a pressure and at too high a distance, it will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in horizontal strokes. Any eventual shift from this position when spraying will result in an uneven application of the paint layer.

FORM OF THE FAN

| – Air pressure too low
– Product viscosity too high
– Quantity of product too high
---|---
| – Air pressure too high
– Product viscosity too low
– Quantity of product too low
| – Regular jet

Adjust the air pressure, product quantity and spray aperture until obtaining a regular imprint as in fig. C

MOD………………………………………………………………………………..6011 / 6010 / 6010 sp HVLP

TECHNICAL SPECIFICATIONS

• Air fitting: G 1/4” M
• Product delivery fitting (version SP): G 1/4” M
• Maximum air pressure: 5 bar (73 psi)
• Maximum product pressure (SP version): 5 bar (73 psi)

ADJUSTMENTS

• Working pressure: 2.5-3.0- bar (36-43 psi)
• Fan: Fully open
• Air: Fully open
• Product: 4 turns

Ø| Feed| Delivery pressure| **Product load| Air consumption at 0.7 bar (10 psi) captest| Fan dimensions at 20 cm (7.9″)
---|---|---|---|---|---
1.| Gravity Suction SP version| 2.5 – 3.0 bar
(36-43 psi)| 110 Gr/min.(3.9 oz/min.)
70 Gr/min. (2.5 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 16 cm (6.2″)
15 cm (5.8″)
1.4
1.7| Gravity Suction Gravity Suction SP version| 120 Gr/min.(4.3 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 17 cm (6.6″)
90 Gr/min.(3.2 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)| 16 cm (6.2″)
220-240 Lt./min (7.8-8.5 CFM)
160 Gr/min.(5.7 oz/min.)
110 Gr/min.(3.9 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 19 cm (7.4 )
18 cm (7″)
| 220-240 Lt./min (7.8-8.5 CFM)|
2.| Gravity Suction SP version| 190 Gr/min.(6.8 oz/min.)
130 Gr/min.(4.6 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 20 cm (7.8″)
19 cm (7.4″)
2.| Gravity Suction SP version| 230 Gr/min.(8.2 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 21 cm (8.2 )
160 Gr/min.(5.7 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 20 cm (7.8″)
c
3.| Gravity Suction i SP version r| 280 Gr/min.(9.9 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 23 cm (9″)
180 Gr/min.(6.4 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 21 cm (8.2″)
|
3.0| Gravity| 340 Gr/min.(12 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 25 cm (9.8″)
Suction| 210 Gr/min.(7.5 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)| 23 cm (9″)
SP version| | 220-240 Lt./min (7.8-8.5 CFM)|

** Product flow was calculated with water, setting the recommended regulations.
RECOMMENDED AIR PRESSURE DURING USE: 2.5 – 3.0 bar (36-43 psi)
At the recommended air pressure the spray gun respects the European and U.S. ecological norms for which the transfer efficiency must be above 65% and /or the air pressure at the exit of the air cap must not be superior to 0.7 bar (10 psi).

… USE
Spray guns int the 6000 HVLP series have been designed for the application of finishing colours in all those sectors requiring high quality finishing and low fumes emission.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:

1.  When possible, use an air pipe with a minimum internal section of ø 8 mm (0.3”).
2. Make sure the compressed air used is perfectly filtered removing all water, oil or other impurities (for example, by installing an Asturomec filter regulator ref. 61131 and Asturomec coalescent microfilter ref. 61201, or by the more complete and efficient WALCOM TD 3 PRO multifunctional filter and heating unit).

ADVICE FOR CORRECT USE

1.  The distance between the spray gun and the surface to be painted must be set between 100 and 150 mm (3.9”- 5.9”). If the spray gun is working at too low a pressure and at too high a distance, il will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in horizontal strokes. Any eventual shift from this position when spraying will result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 15 and 25 sec. Coppa Ford n. 4. These values depend on the application in question and the measure of the nozzle in use.

FORM OF THE FAN

| – Air pressure too low
– Product viscosity too high
– Quantity of product too high
---|---
| – Air pressure too high
– Product viscosity too low
– Quantity of product too low
| – Regular jet

Adjust the air pressure, product quantity and spray aperture until obtaining a regular imprint as in fig. C
MOD……………………………………………………………………………………6011 / 6010 / 6010 sp HTE

TECHNICAL SPECIFICATIONS

• Air fitting: G 1/4” M
• Product delivery fitting (version SP): G 1/4” M
• Maximum air pressure: 5 bar (73 psi)
• Maximum product pressure (SP version): 5 bar (73 psi)

ADJUSTMENTS

• Working pressure: 2.5-3.0- bar (36-43 psi)
• Fan: Fully open
• Air: Fully open
• Product: 4 turns

Ø| Feed| Delivery pressure| **Product load| Air consumption| Fan dimensions at 20 cm (7.9″)
---|---|---|---|---|---
1.| Gravity Suction| 2.5 – 3.0 bar (36-43 psi)| 120 Gr/min.(3.9 oz/min.)
80 Gr/min. (2.5 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 16 cm (6.2″)
15 cm (5.8″)
SP version .10
1.| Gravity Suction SP version| 130 Gr/min.(4.3 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 17 cm (6.6″)
100 Gr/min.(3.2 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)| 16 cm (6.2″)
| 220-240 Lt./min (7.8-8.5 CFM)|
1.7
1 .9| Gravity Suction| 170 Gr/min.(5.7 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 19 cm (7.4 )
120 Gr/min.(3.9 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)| 18 cm (7″)
220-240 Lt./min (7.8-8.5 CFM)
Gravity Suction SP version =| 200 Gr/min.(6.8 oz/min.)
140 Gr/min.(4.6 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)
220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 20 cm (7.8″)
19 cm (7.4″) 1
– –| –
2.| Gravity Suction SP version| 245 Gr/min.(8.2 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 21 cm (8.2 )
170 Gr/min.(5.7 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)| 20 cm (7.8″)
| 220-240 Lt./min (7.8-8.5 CFM)|
3.| Gravity Suction SP version| 290 Gr/min.(9.9 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 23 cm (9″)
190 Gr/min.(6.4 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)| 21 cm (8.2″)
| 220-240 Lt./min (7.8-8.5 CFM)|
3.0| Gravity| 340 Gr/min.(12 oz/min.)| 180-220 Lt./min (6.4-7.8 CFM)| 25 cm (9.8 )
Suction SP version| 210 Gr/min.(7.5 oz/min.)| 220-240 Lt./min (7.8-8.5 CFM)
220-240 Lt./min (7.8-8.5 CFM)| 23 cm (9″)

** Product flow was calculated with water, setting the recommended regulations.
RECOMMENDED AIR PRESSURE DURING USE: 2.5 – 3.0 bar (36-43 psi)
At the recommended air pressure the spray gun respects the European and U.S. ecological norms for which the transfer efficiency must be above 65% and /or the air pressure at the exit of the air cap must not be superior to 0.7 bar (10 psi).
USE
Spray guns int the 6000 HTE series have been designed for the application of finishing colours in all those sectors requiring high quality finishing and low fumes emission.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:

1.  When possible, use an air pipe with a minimum internal section of ø 8 mm (0.3”).
2.  Make sure the compressed air used is perfectly filtered removing all water, oil or other impurities (for example, by installing an Asturomec filter regulator ref. 61131 and Asturomec coalescent microfilter ref. 61201, or by the more complete and efficient WALCOM TD 3 PRO multifunctional filter and heating unit).

ADVICE FOR CORRECT USE

1. The distance between the spray gun and the surface to be painted must be set between 100 and 150 mm (3.9”- 5.9”). If the spray gun is working at too low a pressure and at too high a distance, il will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in horizontal strokes. Any eventual shift from this position when spraying will result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 15 and 25 sec. Coppa Ford n. 4. These values depend on the application in question and the measure of the nozzle in use.

FORM OF THE FAN

| – Air pressure too low
– Product viscosity too high
– Quantity of product too high
---|---
| – Air pressure too high
– Product viscosity too low
– Quantity of product too low
| – Regular jet

Adjust the air pressure, product quantity and spray aperture until obtaining a regular imprint as in fig. C

DECLARATION OF CONFORMITY
WALMEC S.p.A., with headquarters in Via Trieste 10, 31025 S. LUCIA DI PIAVE (TV) – Italy, manufacturer of the following Asturomec® spray guns to pulverise and spray primer and finish product:

• series: NOVEMILA; models HVLP, HTE versions S, I, SP, HD
• series: SEIMILA; models HVLP, HTE versions S, I, SP, HD

STATES that the abovementioned devices meet ATEX 94/9/CE Directive and, thus, are suited for use in potentially explosive atmosphere Zones 1 and 2 within the limits of the classified zones and according to the Instructions for use.
These devices were subject to assessment procedures for Internal Manufacturing Control (Directive 94/9/CE – Appendix VIII).
For this purpose, the following harmonised regulations were applied: UNI EN 1127-1 and UNI EN 13462-1.
Furthermore, the manufacturer STATES that the abovementioned devices meet the essential safety requirements sanctioned by Machinery Directive 2006/42/CE and that harmonised regulations UNI EN 12100 parts 1 and 2 and UNI EN 1953 were applied.
S. Lucia di Piave (TV), January 12, 2012

The Sole Director
Paolo Zanetti

WALMEC ITALY
HEADQUARTERS
WALMEC S.p.A.
Via Trieste, 10
31025 S. LUCIA DI PIAVE (TV) ITALY
Tel. +39 0438 6611
Fax +39 0438 661333
e-mail: walmec@walmec.com
Web: www.walmec.com 
WALMEC ITALY
PRODUCTION PLANT
WALMEC S.p.A.
Viale della Vittoria
24054 CALCIO (BG) ITALY

Documents / Resources

| WALCOM 9011 Spray Gun [pdf] Instructions
9011 Spray Gun, 9011, Spray Gun, Gun
---|---

References

• Home | Walmec S.p.A.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>