ZWO ASI585MC Pro Astrophotography DSO Camera Instruction Manual
- June 1, 2024
- ZWO
Table of Contents
- Product Introduction
- STARVIS 2
- Large Full Well Capacity
- Notice for Use
- Getting to Know Your Camera
- Camera Specifications
- Quantum Efficiency & Read Noise
- Read Noise
- Analog to Digital Converter (ADC)
- Two-stage TEC Cooling
- Power Consumption
- High Transmission Speed
- What’s in the Box?
- Structural Dimension Diagram
- Connection Methods
- Warranty
- Servicing
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZWO ASI585MC Pro Astrophotography DSO Camera Instruction Manual
Thank you so much for purchasing ZWO ASI camera! Before using the product, please read this manual carefully. All materials related to this publication are subject to change without notice and its copyright totally belongs to Suzhou ZWO CO.,LTD.
Product Introduction
-
IMX585 Sensor
-
1/1.2″ 11.2×6.3mm
-
Resolution 3840*2160
-
12bit ADC
-
ADC 12bit
-
Read noise 0.7e
-
Cooling Tempe 35°C
-
DDR3 Buffer 512MB
-
USB 3.0
-
47 FPS
-
Full well 40Ke
-
QE 91%
-
Pixel Size 2.9μm
New DSO Camera with High Sensitivity
ASI585MC Pro is a new ZWO deep sky camera based on the 4k SONY CMOS sensor
with a 1/1.2″ format and 2.9μm pixels. It has a super high sensitivity and
large resolution of 3840*2160 (8.29MP in total). It also features high
transmission speeds – In high speed mode, the fast frame rate can reach 47fps
at full resolution! Being an entry-level DSO camera, it offers great
advantages of high cost-effectiveness.
DSO & Planetary Imaging
The STARVIS 2 technology brings ASI585MC Pro more advanced imaging performance
compared to other cooled cameras. Its high frame rate makes it not only
suitable for DSO photography but also solar/lunar/planetary photography.
STARVIS 2
STARVES 2 was developed by SONY and evolved from STARVES. It is the latest
technology with a wider dynamic range and super-high sensitivity beyond the
human eye. Benefiting from it, ASI585MC Pro’s sensitivity and signal-to-noise
ratio is greatly improved.
Large Full Well Capacity
The back-illuminated structure improves the camera’s full well capacity. Even
with unbinned 2.9μmpixels, ASI585MC Pro has a full well capacity of 40ke-, 3
times of that of the last-generation sensor IMX485. Larger full well capacity
gets the camera higher efficiency in collecting light, and can effectively
restrain the highlight area from being overexposed, also can improve the
signal-to-noise ratio.
No Amp Glow
ASI585MC Pro exhibits extremely clean dark frames with zero amp glow! No
matter how long the exposure and how high the gain value is, you can easily
get a clean and smooth astro images!
Notice for Use
Before using the camera, please read this manual carefully.
External power supplies are needed for all ASl cooled cameras. We recommend you use a 12V@3A~5ADCadapter (D5.5×2.1mm, center pole positive) or a lithium battery with 11-14V to power the camera. You can also use ASIAlR to power the cameras. Be aware that using power supply out of this voltage range will probably lead to irreparable damage to the camera.
Note that the camera can only be used and stored under the following conditions. Usages out of the environment limits might lead to damage to the camera.
Storage temperature | -20°C ~ 60°C |
---|---|
Storage humidity | 20% ~ 95% |
Working temperature | -5℃ ~ 50℃ |
Working humidity | 20% ~ 80% |
Please do not use corrosive solutions to clean the camera to avoid corroding
the oxide layer on the surface and
damaging the camera. Meanwhile, please do not keep the camera exposed to the
sun for a long time to avoid
discoloration of the oxide layer on the camera surface.
Getting to Know Your Camera
External View
- Heat sink
- M42 11mm ring: Can be screwed off if needed.
- AR protective window (D32*2mm)
- USB 2.0 Hub
- USB 3.0/USB 2.0 data transmission port
- LED indicator
- DC power port: D5.5×2.1mm, center pole positive. 12V@3A power supply is recommended to use.
- Ultra-quiet magnetic levitation fan: Only runs when cooling is turned on.
The camera can be supported by the ZWO holder ring. There is a 1/4” screw
interface at the base of the ring.
Camera Specifications
Sensor | Sony-IMX585 |
---|---|
Sensor format | Type 1/1.2 |
Diagonal | 12.84mm |
Resolution | 8.29MP (3840 x 2160) |
Pixel size | 2.9μm |
Sensor size | 11.136mm x 6.264mm |
Max frame rate | 47fps |
Shutter | Rolling shutter |
Exp range | 32μs~2000s |
Read noise | 0.7-6.67 e(3.8e@19.8db |
QE peak | 91% |
Full well capacity | 40ke |
ADC | 12bit |
DDR3 buffer | 512MB |
USB port | USB 3.0 Type-B |
Connection adapter | M42 x 0.75 adapter |
Protective window | D32-2 AR |
Camera diagonal | φ78 x 73.5 |
Net weight | 0.47kg |
Back focus distance | 17.5mm (11mm ring included) / 6.5mm |
Cooling | 2-stage TEC cooling |
Delta-T | 30°~35°@ environmental temperature 30°C |
Power consumption (Cooling on) | 12V, Max current 3A |
Supported OS | Windows, Linux & Mac OSX |
Quantum Efficiency & Read Noise
Quantum Efficiency
According to our test results, the QE peak value of ASI585MC Pro is 91%.
Quantum Efficiency
Relative Response
Read Noise
The camera has a built-in HCG mode, which can effectively reduce read noise at high gain and keep the dynamic range at the same level as it does at low gain. At gain 252 and above, the HCG mode is automatically turned on; the dynamic range is close to 11 stops; the read noise can be lower than 0.7e.
Analog to Digital Converter (ADC)
ASI585MC Pro records in 12 bit ADC and 10 bit ADC. You can image at a faster frame rate if you use 10 bit ADC(high speed mode). Or you may also set an ROI if you want even faster frame rates.
Below are the maximum speeds of ASI585MC Pro running at different USB transmission modes.
Resolution | USB 3.0 | USB 2.0 |
---|---|---|
Normal Mode: 12BIT ADC | High-speed Mode: 10BIT ADC | Normal Mode: 12BIT ADC |
High-speed Mode: 10BIT ADC
RAW16| RAW8| RAW8| RAW16| RAW8| RAW8
38402160| 23.7fps| 46.9fps| 46.9fps| 2.61fps| 5.2fps| 5.2fps
19201080| 91.4fps| 91.4fps| 91.4fps| 10.4fps| 20.8fps| 20.8fps
1280720| 133.5fps| 133.5fps| 133.5fps| 23.5fps| 47fps| 47fps
640480| 192.9fps| 192.9fps| 192.9fps| 70.5fps| 141.3fps| 141.3fps
320*240| 347.3fps| 347.3fps| 347.3fps| 283.1fps| 347.3fps| 347.3fps
Two-stage TEC Cooling
Thanks to the two-stage TEC cooling, ASI585MC Pro can lower the CMOS sensor
temperature to more than 35
degrees Celsius below ambient temperature, which can greatly reduce dark
current generation and sensor noise
even during extended exposure times.
*The Delta T 35℃ is tested at 30℃ ambient temperature. It might get down when the cooling systems working for a long time. Also, as the ambient temperature falls, the Delta T would decrease.
Below is the dark current curve of ASI585MC Pro at the temperature from -20℃
to 30℃.
Power Consumption
All ASI cameras have low power consumption. ASI585MC Pro is no exception. When
it’s at non-cooling status, th e max power consumption is only 2.5W.When it’s
at cooling status, the max power consumption is 22.6W.
High Transmission Speed
512M DDR3 buffer: Can ensure a stable date transmission in the long exposure condition, minimising frame drops and also reducing the requirements for the computer hardware.
USB 3.0 Port: Provides 5Gb bandwidth to allow ASI585MC Pro to run at 47fps at 8.29MP full resolution (RAW8 mode).
USB 2.0 HUB : Can be used to connect various kinds of USB devices such as
EFW, guide camera and EAF.
What’s in the Box?
-
Camera body
-
Camera bag
-
Quick guide
-
M42-M48 Adaptor
-
USB 3.0 Cable (2m)
-
USB 2.0 Cable (0.5m) x2
-
M42-M48 Extender (16.5mm)
-
1.25″ Nonspecific
-
M42-1.25″ Adaptor
-
M42 21mm Extender
-
Spacer x4
-
Cover
The 2m USB 3.0 cable and two 0.5m USB 2.0 cables can meet multiple
requirements in different usage scenarios. For example, the 2m long cable can
be used for guiding with a PC. The 0.5m short cables can be used to connect
ASIAIR to the guide camera or EAF.
Spacers x4 : 0.1mm 1; 0.2mm 2; 0.5mm *1
Structural Dimension Diagram
Connection Methods
Connecting to Nikon/Canon Lens
- M43-T2 adapter (optional)
- EOS-T2 adapter (optional)
- 2” filter (optional)
- 1.25” T-mount
- 1.25” filter (optional)
- M42-1.25” adapter
- 11mm T2 extender
- 16.5mm M42-M48 extender
- T2-T2 adapter
- EFW mini
- EOS lens adapter for EFW
Solutions for 55mm best back focus distance
Connecting to external devices
Warranty
-
ZWO provides Users with a warranty period of 2 years for ZWO branded products. The warranty starts from the second day when the customer gets the product.
-
If a User encounters the following Dead on Arrival (DOA) and contacts ZWO within the corresponding time limit to issue the Product purchase invoice and relevant evidence, ZWO will provide door-to-door pick-up service and, as appropriate, after-sale replacement (or partial replacement), repair or return (or partial return) service for the following Products:
-
Product quality problem
Provided that a User detects a quality problem and contacts ZWO within 30 days after receipt of the Products, and ZWO support team confirms that the Products indeed have a quality problem or defect after their inspection, ZWO will provide free replacement service towards such Products; -
Product transportation problem
Provided that a User finds obvious signs of bubbling, serious overstocking, or deformation on the outer package of the Products upon receipt of the Products, and provides ZWO with pictures of the outer package and proof of receipt within 3 days after receipt of such Products, ZWO support team will verify the actual shipper and determine the responsible party for such transportation problem. In the event that ZWO is the actual shipper, ZWO will be responsible for providing the relevant return or replacement service, however, if the Products are directly sold or transported to the User by an agent of ZWO, the agent will be responsible for providing the relevant return or replacement service. -
If the Products are under the following circumstances, they are not within the scope of warranty
service, ZWO may provide maintenance services to the Users: -
The Warranty Period of the Products has expired; or
-
The Products are injected into liquid or affected by moisture or corrosion; or
-
The Products are damaged by an external force (such as the broken of the camera protection
window glass, the deformation of the product shell, the broken of the USB port, etc.); or -
Disassembling, repairing by a third party, refurbishment of the Products (such as downloading
erroneous firmware) without the written authorisation of ZWO; or -
The product system is modified, or the maintenance notice is lost or changed; or
-
Product quality problem caused by installation not following the requirements or instructions for the Products; or
-
Physical damage or failure of the Products caused by the force majeure (such as strong vibration or extrusion such as flood, fire, earthquake, or thunder stroke); or
-
Damage caused by the improper Customer operation during the period of shooting or use, such
as using without the equipment protection or direct shooting of the sun; or -
No valid purchase invoice or warranty certificate; or
-
The Products are second-hand products.
Servicing
For software upgrades, please refer to “Guide & Manuals” on our official
website. https://www.zwoastro.com/guides-and-manuals/
For repairs and consultation, you can visit here: https://support
.astronomy-imaging-camera.com/
Email: info@zwoptical.com
Phone: 0512-65923102
-
For the normal repair or replacement of the Products during the Warranty Period, the User will bear the return cost. When returning the Products, Users shall specify the actual reasons for the damage to the Products, and shall provide the corresponding valid certificates, such as pictures or videos, etc.
For the Products that need to be replaced after being confirmed by ZWO in writing, the User shall return the Products with the complete package, together with all accessories, manuals, etc., to the address designated by ZWO.
By sending back the product to ZWO, the User agrees to pay out-of-warranty fees that may arise during the repair process of the product. ZWO will send back the product after charging. -
For the Products that need to be returned for after-sales service, ZWO will provide the corresponding RMA code for reference. ZWO will not accept any products having no RMA code that have been returned privately without ZWO written confirmation.
-
If a User purchases the ZWO Products from a ZWO agent, the User may contact the ZWO agent directly for the relevant after-sales service.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>