General Pump 2103410 INDUSTRIAL Hose Reel Electric Motor Kit Instruction Manual
- June 1, 2024
- GENERAL PUMP
Table of Contents
General Pump 2103410 INDUSTRIAL Hose Reel Electric Motor Kit
Specifications
| Part Number | Voltage | Max Amps | Working Temperature |
|---|---|---|---|
| DMC12V | 12 VDC | 30 A | -4°F – 104°F |
Safety Precautions
- Make sure incoming pressure does not exceed the rated pressure.
- Use proper eye protection when assembling and using the hose reel.
- Assemble the hose reel on a clean workbench free of debris and moisture.
- Use soap and water when checking for air leaks.
- Keep children away from the work area.
Powered Hose Reel Assembly Instructions
- On the end of the hose reel opposite the lock, assemble the two ring gear halves to the hose reel using carriage bolts, washers, and lock nuts. Torque to 100 in-lbs.
- Assemble the plate motor with bolts, lock washer, and flat washers as shown. Torque to 100 in-lb.
- Slide spur gear onto motor shaft; gear face will hang over with end of motor shaft by about 5 mm (3/16). Apply a drop of medium-strength thread locker to the set screw and thread into gear. Torque set screw to 20 in-lb.
- Attach motor assembly to hose reel frame using carriage bolts, flat washers (bottom two bolts only), flat washers, and locknuts. Finger tight only for now.
- Rotate the hose reel by hand a few revolutions to get the motor assembly and ring gears to align. Torque the motor assembly nuts to 100 in-lb.
FAQ
-
Q: What should I do if I encounter air leaks?
A: Use soap and water to check for air leaks. Ensure all connections are tight and sealed properly. -
Q: Can children operate the hose reel?
A: No, children should be kept away from the work area and should not operate the hose reel. -
Q: What is the maximum amperage supported by this product?
A: The maximum supported amperage is 30A when operating at 12VDC.
ACCESSORIES
DMC12V: 12 Volt DC Variable Speed Controller Rewind Kit
- 30 amp auto-reset circuit breaker
- Heavy duty momentary on/off switch
- Variable speed knob with built in on/off function
- LED power indicator light
- Reversible powder-coated mounting plate for left or right orientation
- Sealed Housing
FEATURES
- Part Number DMC12V
- Voltage 12 VDC
- Max Amps 30 A
- Working Temperature -4⁰F – 104⁰F
SAFETY PRECAUTIONS
- Make sure incoming pressure does not exceed the rated pressure.
- Use proper eye protection when assembling and using the hose reel.
- Assemble the hose reel on a clean workbench free of debris and moisture.
- Use soap and water when checking for air leaks.
- Keep children away from the work area.
WARNING!
Exposure of skin directly to pressurized air or fluids could result in severe
bodily injury!
INDUSTRIAL Hose Reel ElectricMotor Kit
- POWERFUL 12V DC MOTOR
- LONG LASTING HARDENED GEARS
- HOSE REEL SOLD SEPARATELY
- Weight: 21 lbs.
POWERED HOSE REEL ASSEMBLY INSTRUCTIONS
- On the end of the hose reel opposite the lock, assemble the two ring gear halves to the hose reel using carriage bolts, washers and lock nuts. Two alignment pins are supplied to make it easier. Torque to 100 in-lbs.
- Assemble the plate motor with bolts, lock washer and flat washers as shown. Torque to 100 in-lb.
- Slide spur gear onto motor shaft; gear face will hang over with end of motor shaft by about 5 mm (3/16”). Apply a drop of medium-strength thread locker to the set screw and thread into gear. Torque set screw to 20 in-lb
- Attach the motor assembly to hose reel frame using carriage bolts, flatwashers (bottom two bolts only), flat washers, and locknuts. Finger tight only for now.
- Rotate the hose reel by hand a few revolutions to get the motor assembly and ring gears to align. Torque the motor assembly nuts to 100 in-lb.
DIMENSION
General Pump
1174 Northland Drive
Mendota Heights, MN 55120
Phone: 651.686.2199
Fax: 800.535.1745
www.generalpump.com
email: sales@gpcompanies.com
General Pump is a member of The Interpump Group
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>