tuya PST-IR101 Wired Wide Angle PIR Motion Sensor Instruction Manual

tuya PST-IR101 Wired Wide Angle PIR Motion Sensor

Product Information

Specifications

• Operating Voltage: DC 9V-16V
• Current Consumption: 18mA (DC12V)
• Detecting Distance: 12m
• Detecting Angle: 110 degrees
• Self-testing Time: Approximately 60 seconds
• Working Temperature: -10°C to +50°C
• Alarm Indicator: Red LED
• Alarm Output: N.C. or N.O., DC28V, 100mA
• Temperature Output: N.C., DC28V, 100mA
• Range of Coverage: 11m distance, 8m middle, 5m vicinities
• Sensor: Dual element infrared sensor
• Operating Temperature: -10°C to +50°C
• Environment Humidity: 95% RH (no congelation)
• Anti RF Interference: 10MHz-1GHz, 20V/m
• Installation Mode: Wall mounted or hanged in corner
• Installation Height: 1.7m to 2.5m (2.2m proposed)
• Outline Size: 52.5L38.5W89H mm

Product Usage Instructions

Installation

1. Avoid installing the detector outdoors, near pets, air-conditioning units, direct sunlight, heat sources, or rotating objects.
2. The installation surface should be firm and free of vibrations.
3. Install the detector in a location where intruders are likely to pass.

Installation Steps

1. Screw off the detector bottom and open it.
2. Screw off the PCB and remove it.
3. Drill a wire hole in the rear housing.
4. Install the rear housing in a suitable position.
5. Connect the terminal block as indicated.

Operating Instructions

Function Setting

1. Relay Jumper: Choose between NC or NO for alarm output state.
2. Pulse Jumper: Adjust sensitivity and anti RF interference.
3. LED Jumper: Control LED indicator.

Frequently Asked Questions (FAQ)

• Q: Can the detector be used outdoors?
  A: It is recommended to avoid outdoor installations due to potential interference from environmental factors.

• Q: How can I adjust the sensitivity of the detector?
  A: You can adjust the sensitivity by selecting the appropriate Pulse Jumper setting as mentioned in the manual.

• Q: What is the recommended installation height?
  A: The proposed installation height is between 1.7m to 2.5m, with 2.2m being the suggested height for optimal performance.

MANUAL FOR WIDE ANGLE PIR DETECTOR

PRODUCT INTRODUCTION

The product is passive infrared detector with high stability. I t h as adopted advanced technology in signal processing and provided superhigh detection ability and anti error alarm. The detector will detect movement of human automatically when intruder passes through the detection area, and it w ill send out alarm s ignal to alarm host if there is movement. The product is suitable for the safety of residential house, villas, factories, markets, warehouses, office building etc.

PRODUCT PROFILE

1. Wire Exit
2. Terminal Block
3. Anti-dismantle Switch
4. Relay
5. LED Indicator
6. LED Jumper
7. Relay Jumper
8. Dual Element IR Sensor
9. Thermistor Resistance
10. Pulse Jumper
11. PCB

MAIN FEATURE

• Intelligent logic control, anti false alarm efficiently
• Auto temperature compensation
• Pulse count adjustment
• Anti white light interference
• Anti RF interference(20V/m-1GHz)
• Fresnel lens
• Wall/ceiling installation
• SMT design adopted
• Alarm output N.C. / N.O., Anti RF interference

TECHNICAL SPECIFICATION

• Operating voltage: DC 9V 16V
• Current comsuption: 18mA(DC12V)
• Detecting distance: 12m
• Detecting angle: 110
• Self-testing time: 60S or so
• Working temperature: -10 ~+50
• Alarm indicator: red LED
• Alarm output:N.C. or N.O., DC28V,100mA
• Temper output: N.C., DC28V, 100mA
• Range of coverage: 11 distance, 8 middle, 5 vicinities
• Sensor: dual element infrared sensor
• Operating temperature: -10 to +50
• Environment humidity: 95% RH (no congelation)
• Anti RF interference: 10MHz 1GHz 20V/m
• Installation mode: wall mounted or hanged in corner
• Installation height: 1.7 to 2.5m (2.2m is Proposed)
• Outline Size: 52.5L38.5W89H mm

INSTALLATION

1. Installation at the out door,place with pets, air-condition nearby, direct sunshine, heat source and under the rotating objects should be avoided.
2. Surface of installation should be firm with no vibration.
3. Installing the detector in the place where intruder pass easily.

INSTALLATION STEP

1. Screw the detector bottom off, then open the detector.
2. Screw the PCB off and remove the PCB.
3. Drill a wire holein the rear housing.
4. Install the rear housing on the suitable position.
5. Connect the terminal block.(as follows)

TERMINAL BLOCK FIGTURE

• +12V DVANODE
• GND DV CATHODE
• ALARM ALARM OUTPUT PORT
• TAMPER ANTI-TEMPER OUTPUT PORT

OPERATING INSTRUCTION

Function Setting

1. Relay Jumper: Choose NC or NO to set the state of alarm output. You should choose different alarm output in accordance with host.
2. Short 1&2: N.O.
3. Short 2&3: N.C. (Factory-set)
4. Pulse Jumper: You can adjust the sensitivity and anti RF interference by choosing the Pulse Jumper.
5. Short 1&2: class 1 pulse, the sensitivity is highest, adapt to general environment.
6. Short 2&3: class 2 pulse,anti RF interference is high, adapt to the environment with strong RF interference.
7. Shut off: class 3 pulse, the sensitivity is lower, and the anti RF interference is highest, adapt to the environment with exceeding RF interference.
8. LED Jumper: Control LED indicator, without effect of detector normal work.
9. Short 1&2: set LED ON
10. Short 2&3: set LED OFF

LED can be shut off for concealment of the detector after Test

Product testing
Turning on power and LED indicator on, the detector comes into state of self- check, it takes about 60s, after that it is in the state of normal work. Conner should walk parallel with the wall installed detector in the testing area. LED lighting means the detector is in the state of alarm.

NOTICE

1. Please install and use the detector according to this manual, don’t touch the surface of sensor for avoiding affecting the sensitivity of the detector. Please shut off power and then clean the sensor by soft cloth with little alcohol if cleaning needed.
2. The product can reduce accident but may not perform as expected. The user is advised to take all necessary precautions for his/her safety and the protection of his/her property.
3. In order to ensure it can work normally, the power should be kept to supply and get on walking test periodically, once a week is better.

JUMPER SETTING FIGURE

Detecting Area View

Documents / Resources

| tuya PST-IR101 Wired Wide Angle PIR Motion Sensor [pdf] Instruction Manual
PST-IR101 Wired Wide Angle PIR Motion Sensor, PST-IR101, Wired Wide Angle PIR Motion Sensor, Wide Angle PIR Motion Sensor, Angle PIR Motion Sensor, PIR Motion Sensor, Motion Sensor, Sensor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>